VCR REPAIR TIPS PAGE 8
MAKE MODEL CHASSIS SYMPTOM CURE
TOSHIBA M4330 N/A WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA M4330 N/A INT. SPEED SELECT IC501
TOSHIBA M440 N/A NO FF/REW AND TAPE JAMS IN REC/PLAYBACK THIS IS CAUSED BY LOW REEL TORQUE--
TOSHIBA M442 N/A NO PLAYBACK COLOR CHECK/REPLACE C230 (1uF @ 16v)
TOSHIBA M442 N/A SLOW LOADING AND UNLOADING TAPE - DRUM SERVO AND CAPSTAN SERVOS ARE SLUGGISH - 33V SUPPLY TO TUNER LOW CHECK/REPLACE D001 (33v ZENER)
TOSHIBA M442 N/A NO PICTURE OR INTERMITTENT BLUE SCREEN ADD A WIRE FROM GROUND TO PIN 9 OF PV01
TOSHIBA M442 N/A NO PICTURE OR INTERMITTENT BLUE PICTURE CHECK/SOLDER WIRE FROM PIN #9 OF PV01 TO GROUND INSIDE HEAD AMP ASSEMBLY
TOSHIBA M444 N/A DEAD - NO POWER CHECK/REPLACE PW801 (P/N3 BZ680032)
TOSHIBA M447 N/A NO PLAYBACK COLOR CHECK/REPLACE C230 (1uF @ 16v)
TOSHIBA M447 N/A NO PICTURE OR INTERMITTENT BLUE SCREEN ADD A WIRE FROM GROUND TO PIN 9 OF PV01
TOSHIBA M447 N/A NO PICTURE OR INTERMITTENT BLUE PICTURE CHECK/SOLDER WIRE FROM PIN #9 OF PV01 TO GROUND INSIDE HEAD AMP ASSEMBLY
TOSHIBA M447 N/A SLOW LOADING AND UNLOADING TAPE - DRUM SERVO AND CAPSTAN SERVOS ARE SLUGGISH - 33V SUPPLY TO TUNER LOW CHECK/REPLACE D001 (33v ZENER)
TOSHIBA M448 N/A CASSETTE WILL NOT LOAD OR CASSETTE LOADS BUT THEN IS EJECTED OR CASSETTE WILL NOT EJECT REPLACE RIGHT SIDE PLATE (P/N # 70790457) , SHAFT ARM ASSY. (P/N # 70790005) AND EJECT GEAR (P/N # 70790393)
TOSHIBA M448 N/A DEAD WITH OR WITHOUT FUSE BLOWN CHECK/REPLACE Q1,Q2 AND D02 IN POWER SUPPLY
TOSHIBA M448 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA M448 N/A NO POWER - FUSE F1 BLOWN INSTALL PARTS IN THE FOLLOWING KIT (P/N# 70796058)
TOSHIBA M449 N/A NO VIDEO THROUGH INPUT JACKS ON THE FRONT OF UNIT CHECK/REPLACE IC801 (P/N# ECG4053)
TOSHIBA M449 N/A CASSETTE WILL NOT LOAD OR CASSETTE LOADS BUT THEN IS EJECTED OR CASSETTE WILL NOT EJECT REPLACE RIGHT SIDE PLATE (P/N # 70790457) , SHAFT ARM ASSY. (P/N # 70790005) AND EJECT GEAR (P/N # 70790393)
TOSHIBA M449 N/A DEAD OR DISPLAY FLASHES CHECK/REPLACE C04 AND C09
TOSHIBA M449 N/A ONLY RECORDS SNOW ON VIDEO - AUDIO IS RECORDED FINE CHECK/REPLACE R357 (1K @ 1/8w.)
TOSHIBA M45 N/A CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE CAPSTAN MOTOR (REF# B256) (P/N# 70790691)
TOSHIBA M4500 N/A WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA M452 N/A AUDIO IN THE E/E MODE IS LOWER THAN WHEN VCR IS TURNED OFF ADD A 220?1/8w RESISTOR (P/N# 24376221) IN PARALLEL WITH RA01
TOSHIBA M4520 N/A WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA M4530 N/A WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA M456 N/A UNIT TRIES TO LOAD A CASSETTE WITHOUT ONE IN IT - TURNS OFF AFTER A FEW SECONDS CHECK/RESOLDER CONNECTIONS ON S601 AND S602
TOSHIBA M458 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA M458 N/A WHEN REPLACING THE AUDIO/CTRL HEAD WITH A SUBSTITUTE, THE BIAS CURRENT MUST BE RE-ADJUSTED MATSUSHITA TYPE (P/N # 70182066) BIAS CURRENT = 3.4 mV TDK TYPE (P/N # 70182084) BIAS CURRENT = 2.9 mV
TOSHIBA M458 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , R724 & R725 TO SHORT AND C722 TO C-TYPE (P/N # 24285103)
TOSHIBA M458 N/A WILL NOT PLAY DUE TO A LOADING MALFUNCTION CHANGE SOFT BRAKE LEVER WITH NEW TYPE ITEM #K128 (P/N 70363026)
TOSHIBA M458 N/A INTERMITTENT RECORDING OF LINEAR AUDIO - OLD AUDIO NOT BEING ERASED CHANGE C722 TO 0.01uF (P/N# 24287103), SHORT EITHER R724 OR R725, CHANGE R722 TO A 18k (P/N# 24871393)
TOSHIBA M46 N/A AUDIO IN THE E/E MODE IS LOWER THAN WHEN VCR IS TURNED OFF ADD A 220?1/8w RESISTOR (P/N# 24376221) IN PARALLEL WITH RA01
TOSHIBA M461 N/A UNIT TRIES TO LOAD A CASSETTE WITHOUT ONE IN IT - TURNS OFF AFTER A FEW SECONDS CHECK/RESOLDER CONNECTIONS ON S601 AND S602
TOSHIBA M461 N/A INTERMITTENTLY TRIES TO LOAD WITH NO TAPE INSERTED CHECK/RESOLDER CONNECTIONS ON S601 (START SENSOR)
TOSHIBA M462 N/A CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE CAPSTAN MOTOR (REF# B256) (P/N# 70790691)
TOSHIBA M468 N/A WHEN REPLACING THE AUDIO/CTRL HEAD WITH A SUBSTITUTE, THE BIAS CURRENT MUST BE RE-ADJUSTED MATSUSHITA TYPE (P/N # 70182066) BIAS CURRENT = 3.4 mV TDK TYPE (P/N # 70182084) BIAS CURRENT = 2.9 mV
TOSHIBA M468 N/A INTERMITTENT RECORDING OF LINEAR AUDIO - OLD AUDIO NOT BEING ERASED CHANGE C722 TO 0.01uF (P/N# 24287103), SHORT EITHER R724 OR R725, CHANGE R722 TO A 18k (P/N# 24871393)
TOSHIBA M468 N/A WILL NOT PLAY DUE TO A LOADING MALFUNCTION CHANGE SOFT BRAKE LEVER WITH NEW TYPE ITEM #K128 (P/N 70363026)
TOSHIBA M468 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , R724 & R725 TO SHORT AND C722 TO C-TYPE (P/N # 24285103)
TOSHIBA M471 N/A UNIT TRIES TO LOAD A CASSETTE WITHOUT ONE IN IT - TURNS OFF AFTER A FEW SECONDS CHECK/RESOLDER CONNECTIONS ON S601 AND S602
TOSHIBA M472 N/A CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE CAPSTAN MOTOR (REF# B256) (P/N# 70790691)
TOSHIBA M473 N/A AUDIO IN THE E/E MODE IS LOWER THAN WHEN VCR IS TURNED OFF ADD A 220?1/8w RESISTOR (P/N# 24376221) IN PARALLEL WITH RA01
TOSHIBA M5000 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5000 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5000 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5010 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5010 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5010 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5020 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5020 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5020 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5100 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5100 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5100 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5100 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5100 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5100 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5100 N/A INT. SPEED SELECT IC501
TOSHIBA M5100 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5120 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5120 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5120 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5120 N/A INT. SPEED SELECT IC501
TOSHIBA M5120 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5120 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5120 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5120 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5130 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5130 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5130 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5130 N/A INT. SPEED SELECT IC501
TOSHIBA M5130 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5130 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5130 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5130 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5200 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5200 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5200 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5300 N/A DEAD--NO FIP CHECK R817 FOR OPEN
TOSHIBA M5300 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5300 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5300 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5300 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5300 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5300 N/A DRUM/CAPSTAN RUNS CONTINUOUS MICROPROCESSOR IC DEFECTIVE
TOSHIBA M5300 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5300 N/A INT. SPEED SELECT IC501
TOSHIBA M5300 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5300 N/A NO VCR/TV SWITCHING--AFTER LIGHTNING ESPECIALLY Q614 SHORTED--SOMETIMES RF CONVERTER
TOSHIBA M5320 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5320 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5320 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5320 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5320 N/A DEAD--NO FIP CHECK R817 FOR OPEN
TOSHIBA M5320 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5320 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5320 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5320 N/A INT. SPEED SELECT IC501
TOSHIBA M5330 N/A DEAD--NO FIP CHECK R817 FOR OPEN
TOSHIBA M5330 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5330 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5330 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5330 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5330 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5330 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5330 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5330 N/A INT. SPEED SELECT IC501
TOSHIBA M5400 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5400 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5400 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5410 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5410 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5410 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5420 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5420 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5420 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5483 N/A WILL NOT ERASE OLD AUDIO CHECK/REPLACE IC701 AND Q702
TOSHIBA M5487 N/A WILL NOT ERASE OLD AUDIO CHECK/REPLACE IC701 AND Q702
TOSHIBA M5500 N/A INT. SPEED SELECT IC501
TOSHIBA M5500 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5500 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5500 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5500 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5500 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5500 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5520 N/A INT. SPEED SELECT IC501
TOSHIBA M5520 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5520 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5520 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5520 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5520 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5520 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5530 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5530 N/A INT. SPEED SELECT IC501
TOSHIBA M5530 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5530 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5530 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5530 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5530 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5530 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5600 N/A CAPSTAN MOTOR DOESN'T ROTATE REPLACE CAPSTAN MOTOR WITH IMPROVED VERSION #70125183
TOSHIBA M5600 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5600 N/A P.B PIX VERY NOISY WITH EXCESSIVE DROPOUTS CHECK SOLDER CONNECTIONS ON BOTTOM OF UPPER CYL.
TOSHIBA M5900 N/A POWER MAY NOT TURN ON REPL. JP835 W/290 OHM-ADD 100uF>>PIN#15 OF WX02>>GRD.
TOSHIBA M5900 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M5900 N/A PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD REPLACE CAM SWITCH (SJ00251)
TOSHIBA M5900 N/A NO REWIND/FAST FORWARD OR LOW TORQUE IC507,IC603,IC601
TOSHIBA M5900 N/A (INDEXING) ERRORS FINDING THE BEGINNING OF REC. ADD .1uF BETWEEN PIN 1 & 2 OF P704
TOSHIBA M5900 N/A PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M5900 N/A INT. SPEED SELECT IC501
TOSHIBA M5900 N/A HORZ. BAR THUR PIX ABOUT 2' WIDE IC501
TOSHIBA M5900 N/A POWER MAY NOT TURN ON MODIFICATION KIT P/N #70901646
TOSHIBA M5900 N/A FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT. IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA M5900 N/A COLORED VERTICAL NOISE BARS IN PLAY MODE-DARK PX REPLACE THE 1H DELAY LINE X401 (70138064)
TOSHIBA M5900 N/A NO FAST FORWARD OR REWIND THEN POWER SHUTS OFF REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA M6000 N/A WILL RUN FOR 3-4 SECONDS IN F/F THEN EJECTS TAPE CHANGE R628 FROM 120K TO 24K
TOSHIBA M6002 N/A WILL RUN FOR 3-4 SECONDS IN F/F THEN EJECTS TAPE CHANGE R628 FROM 120K TO 24K
TOSHIBA M6003 N/A WILL RUN FOR 3-4 SECONDS IN F/F THEN EJECTS TAPE CHANGE R628 FROM 120K TO 24K
TOSHIBA M6005 N/A WILL RUN FOR 3-4 SECONDS IN F/F THEN EJECTS TAPE CHANGE R628 FROM 120K TO 24K
TOSHIBA M6005 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M6007 N/A WILL RUN FOR 3-4 SECONDS IN F/F THEN EJECTS TAPE CHANGE R628 FROM 120K TO 24K
TOSHIBA M6100 N/A DOES NOT ERASE OR RECORD AUDIO REPLACE Q0501 AND HARD WIRE FULL ERASE HEAD
TOSHIBA M6100 N/A WILL NOT LOAD TAPE--INTERMITTENT CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA M6100 N/A E-E VIDEO IS MUTED--O.S.D. DOES COME ON CHECK C0317 (.0027uF)
TOSHIBA M63 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , SHORT EITHER R724 OR R725 CHANGE C722 TO NEW TYPE (P/N # 24285103)
TOSHIBA M648 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA M648 N/A CASSETTE WILL NOT LOAD OR CASSETTE LOADS BUT THEN IS EJECTED OR CASSETTE WILL NOT EJECT REPLACE RIGHT SIDE PLATE (P/N # 70790457) , SHAFT ARM ASSY. (P/N # 70790005) AND EJECT GEAR (P/N # 70790393)
TOSHIBA M648 N/A NO POWER - FUSE F1 BLOWN INSTALL PARTS IN THE FOLLOWING KIT (P/N# 70796058)
TOSHIBA M649 N/A CASSETTE WILL NOT LOAD OR CASSETTE LOADS BUT THEN IS EJECTED OR CASSETTE WILL NOT EJECT REPLACE RIGHT SIDE PLATE (P/N # 70790457) , SHAFT ARM ASSY. (P/N # 70790005) AND EJECT GEAR (P/N # 70790393)
TOSHIBA M65 N/A CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE CAPSTAN MOTOR (REF# B256) (P/N# 70790691)
TOSHIBA M650 N/A COLOR SHADING IN THE PICTURE (LOOKS LIKE A PURITY PROBLEM) CHECK/REPLACE SHAFT (P/N# 70364004) AND IMPEDANCE ROLLER (P/N# 70346452)
TOSHIBA M650 N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70031431)
TOSHIBA M650 N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v)- REMOVE C802
TOSHIBA M656 N/A UNIT TRIES TO LOAD A CASSETTE WITHOUT ONE IN IT - TURNS OFF AFTER A FEW SECONDS CHECK/RESOLDER CONNECTIONS ON S601 AND S602
TOSHIBA M657 N/A WILL NOT PLAY DUE TO A LOADING MALFUNCTION CHANGE SOFT BRAKE LEVER WITH NEW TYPE ITEM #K128 (P/N 70363026)
TOSHIBA M657 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA M657 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , SHORT EITHER R724 OR R725 TO SHORT, CHANGE C722 TO NEW TYPE (P/N # 24285103)
TOSHIBA M657 N/A WHEN REPLACING THE AUDIO/CTRL HEAD WITH A SUBSTITUTE, THE BIAS CURRENT MUST BE RE-ADJUSTED MATSUSHITA TYPE (P/N # 70182066) BIAS CURRENT = 3.4 mV TDK TYPE (P/N # 70182084) BIAS CURRENT = 2.9 mV
TOSHIBA M658 N/A WILL NOT PLAY DUE TO A LOADING MALFUNCTION CHANGE SOFT BRAKE LEVER WITH NEW TYPE ITEM #K128 (P/N 70363026)
TOSHIBA M658 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , SHORT EITHER R724 OR R725 CHANGE C722 TO NEW TYPE (P/N # 24285103)
TOSHIBA M658 N/A WHEN REPLACING THE AUDIO/CTRL HEAD WITH A SUBSTITUTE, THE BIAS CURRENT MUST BE RE-ADJUSTED MATSUSHITA TYPE (P/N # 70182066) BIAS CURRENT = 3.4 mV TDK TYPE (P/N # 70182084) BIAS CURRENT = 2.9 mV
TOSHIBA M658 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA M659 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , SHORT EITHER R724 OR R725 CHANGE C722 TO NEW TYPE (P/N # 24285103)
TOSHIBA M66 N/A AUDIO IN THE E/E MODE IS LOWER THAN WHEN VCR IS TURNED OFF ADD A 220?1/8w RESISTOR (P/N# 24376221) IN PARALLEL WITH RA01
TOSHIBA M660 N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v) - REMOVE C802
TOSHIBA M660 N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70031431)
TOSHIBA M660 N/A COLOR SHADING IN THE PICTURE (LOOKS LIKE A PURITY PROBLEM) CHECK/REPLACE SHAFT (P/N# 70364004) AND IMPEDANCE ROLLER (P/N# 70346452)
TOSHIBA M661 N/A INTERMITTENTLY TRIES TO LOAD WITH NO TAPE INSERTED CHECK/RESOLDER CONNECTIONS ON S601 (START SENSOR)
TOSHIBA M661 N/A UNIT TRIES TO LOAD A CASSETTE WITHOUT ONE IN IT - TURNS OFF AFTER A FEW SECONDS CHECK/RESOLDER CONNECTIONS ON S601 AND S602
TOSHIBA M662 N/A CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE CAPSTAN MOTOR (REF# B256) (P/N# 70790691)
TOSHIBA M668 N/A WILL NOT PLAY DUE TO A LOADING MALFUNCTION CHANGE SOFT BRAKE LEVER WITH NEW TYPE ITEM #K128 (P/N 70363026)
TOSHIBA M668 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , R724 & R725 TO SHORT AND C722 TO C-TYPE (P/N # 24285103)
TOSHIBA M668 N/A WHEN REPLACING THE AUDIO/CTRL HEAD WITH A SUBSTITUTE, THE BIAS CURRENT MUST BE RE-ADJUSTED MATSUSHITA TYPE (P/N # 70182066) BIAS CURRENT = 3.4 mV TDK TYPE (P/N # 70182084) BIAS CURRENT = 2.9 mV
TOSHIBA M671 N/A NO POWER - DEAD SET CHECK/REPLACE D810 (P/N# 70012564) *** THIS DEVICE SHOULD CHECK OPENAND NOT LIKE A DIODE ***
TOSHIBA M672 N/A CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE CAPSTAN MOTOR (REF# B256) (P/N# 70790691)
TOSHIBA M750 N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v) - REMOVE C802
TOSHIBA M750 N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70031431)
TOSHIBA M750 N/A COLOR SHADING IN THE PICTURE (LOOKS LIKE A PURITY PROBLEM) CHECK/REPLACE SHAFT (P/N# 70364004) AND IMPEDANCE ROLLER (P/N# 70346452)
TOSHIBA M750J N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70324886)
TOSHIBA M750J N/A COLOR SHADING IN THE PICTURE (LOOKS LIKE A PURITY PROBLEM) CHECK/REPLACE SHAFT (P/N# 70364004) AND IMPEDANCE ROLLER (P/N# 70346452)
TOSHIBA M750J N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v) - REMOVE C802
TOSHIBA M750J N/A CASSETTE EJECTS IMMEDIATELY AFTER BEING LOADED CHECK/REPLACE CASSETTE HOLDER (K490) WITH (P/N# 70324886)
TOSHIBA M751 N/A DEAD - NO BLOWN FUSES CHECK/REPLACE D821 SHORTED (P/N# ECG587)
TOSHIBA M758 N/A WILL NOT PLAY DUE TO A LOADING MALFUNCTION CHANGE SOFT BRAKE LEVER WITH NEW TYPE ITEM #K128 (P/N 70363026)
TOSHIBA M758 N/A WHEN REPLACING THE AUDIO/CTRL HEAD WITH A SUBSTITUTE, THE BIAS CURRENT MUST BE RE-ADJUSTED MATSUSHITA TYPE (P/N # 70182066) BIAS CURRENT = 3.4 mV TDK TYPE (P/N # 70182084) BIAS CURRENT = 2.9 mV
TOSHIBA M758 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA M758 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , R724 & R725 TO SHORT AND C722 TO C-TYPE (P/N # 24285103)
TOSHIBA M759 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , R724 & R725 TO SHORT AND C722 TO C-TYPE (P/N # 24285103)
TOSHIBA M760 N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70031431)
TOSHIBA M760 N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v) - REMOVE C802
TOSHIBA M7603 N/A DEAD - NO CLOCK DISPLAY OR ANY FUNCTION - ALSO NO 4MHz CLOCK ON THE TIMER IC CHECK/REPLACE DX20 (ECG177)
TOSHIBA M7607 N/A DEAD - NO CLOCK DISPLAY OR ANY FUNCTION - ALSO NO 4MHz CLOCK ON THE TIMER IC CHECK/REPLACE DX20 (ECG177)
TOSHIBA M760J N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v) - REMOVE C802
TOSHIBA M760J N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70324886)
TOSHIBA M769 N/A INTERMITTENT AUDIO RECORDING CHANGE R722 TO 18k , R724 & R725 TO SHORT AND C722 TO C-TYPE (P/N # 24285103)
TOSHIBA M770 N/A TV PICKS UP POWER SUPPLY SWITCHING INTERFERENCE FROM VCR INSTALL KIT (P/N# 70903925) WHICH HAS C817 (1000pF @ 50v), C819 (100pF @ 1KV), C833/C834 (2200pF @ 125v) - REMOVE C802
TOSHIBA M770 N/A CASSETTE NOT LOADING PROPERLY OR NOT STAYING IN VCR CHECK/REPLACE REF# K490 (P/N# 70031431)
TOSHIBA SVF990 N/A VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA VM411 N/A WON'T LOAD OR UNLOAD-OR NOISY WHILE DOING EITHER REPL. LOADING DRIVE ASSY. (70312151)
TOSHIBA VM411 N/A PIX FINE BUT NO SOUND THRU MODULATOR-AUD. OUT OK REPLACE RF MODULATOR
TOSHIBA VM415 N/A PIX FINE BUT NO SOUND THRU MODULATOR-AUD. OUT OK REPLACE RF MODULATOR
TOSHIBA VM415 N/A WON'T LOAD OR UNLOAD-OR NOISY WHILE DOING EITHER REPL. LOADING DRIVE ASSY. (70312151)
WARDS GEN10525 N/A TAPE PLAYS VERY FAST - ALL SPEEDS ADJUST PINCH ROLLER ASSEMBLY
WARDS GEN10525 N/A TUNER VIDEO/AUDIO IS INTERMITTENT CHECK CONNECTIONS ON AUDIO/VIDEO INPUT JACKS ON THE FRONT PANEL.
WARDS GEN10525 N/A TAPE WILL LOAD/EJECT BUT NO OTHER FUNCTIONS WILL WORK CHECK FOR A BURNED OUT SENSOR LAMP
WARDS GEN10526 N/A TAPE PLAYS VERY FAST - ALL SPEEDS ADJUST PINCH ROLLER ASSEMBLY
WARDS JSJ10550 N/A PLAYBACK LED ON CONTINUOUSLY-NO TUNER OPERATION-NO E-E OR V-V SWITCHING- STUCK IN V-V MODE CHECK/REPLACE IC802 (IR2403)
WARDS JSJ10551 N/A PLAYBACK LED ON CONTINUOUSLY-NO TUNER OPERATION-NO E-E OR V-V SWITCHING- STUCK IN V-V MODE CHECK/REPLACE IC802 (IR2403)
WARDS JSJ10605 N/A FUNCTIONS LOCK UP OR VCR GETS CONFUSED CHECK/REPLACE OR CLEAN MODE SELECT SWITCH
WARDS JSJ10612 N/A BOTH SERVOS OFF - CAPSTAN IS TOO SLOW AND DRUM IS TOO FAST ALSO NO REW OR FAST FORWARD ALTHOUGH INDICATORS APPEAR. CHECK/REPLACE IC701
WARDS JSJ10612 N/A DEAD - WILL NOT POWER UP CHECK R923
WARDS JSJ10612 N/A LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE. CHECK/REPLACE IC801
WARDS JSJ10612 N/A WILL NOT LOAD CASSETTE REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
WARDS JSJ10612 N/A CAPSTAN MOTOR WILL NOT OPERATE REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
WARDS JSJ10612 N/A NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
WARDS JSJ10612 N/A NO AUDIO IN THE RECORD MODE CHECK/REPLACE Q602 (ECG382) ALSO HARDWIRE ERASE HEADS (FULL AND AUDIO)
WARDS JSJ10612 N/A WILL NOT LOAD -- DRUM WILL NOT RUN CHECK R902 FOR OPEN
WARDS JSJ10612 N/A INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
WARDS JSJ10612 N/A VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
WARDS JSJ10612 N/A DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY. CHECK/REPLACE Q812 FOR SHORT OR OPEN
WARDS JSJ10615 N/A LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE. CHECK/REPLACE IC801
WARDS JSJ10615 N/A DEAD - WILL NOT POWER UP CHECK R923
WARDS JSJ10615 N/A VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
WARDS JSJ10615 N/A WILL NOT LOAD CASSETTE REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
WARDS JSJ10615 N/A INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
WARDS JSJ10615 N/A BOTH SERVOS OFF - CAPSTAN IS TOO SLOW AND DRUM IS TOO FAST ALSO NO REW OR FAST FORWARD ALTHOUGH INDICATORS APPEAR. CHECK/REPLACE IC701
WARDS JSJ10615 N/A WILL NOT LOAD -- DRUM WILL NOT RUN CHECK R902 FOR OPEN
WARDS JSJ10615 N/A CAPSTAN MOTOR WILL NOT OPERATE REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
WARDS JSJ10615 N/A NO AUDIO IN THE RECORD MODE CHECK/REPLACE Q602 (ECG382) ALSO HARDWIRE ERASE HEADS (FULL AND AUDIO)
WARDS JSJ10615 N/A DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY. CHECK/REPLACE Q812 FOR SHORT OR OPEN
WARDS JSJ10615 N/A NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
WARDS JSJ10620 N/A UNIT SHUTS OFF - LOAD POST GOES PART OF THE WAY UP THEN STOPS AND VCR RETURNS TO STOP MODE CHECK/REPLACE MODE SELECT SWITCH (P/N# QSW-R0023GEZZ)
WARDS JSJ10622 N/A VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
WARDS JSJ10622 N/A CAPSTAN MOTOR WILL NOT OPERATE REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
WARDS JSJ10622 N/A NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
WARDS JSJ10622 N/A NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
WARDS JSJ10622 N/A CAPSTAN MOTOR WILL NOT OPERATE REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
WARDS JSJ10622 N/A LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE. CHECK/REPLACE IC801
WARDS JSJ10622 N/A LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE. CHECK/REPLACE IC801
WARDS JSJ10622 N/A VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
WARDS JSJ10622 N/A CAPSTAN MOTOR WILL NOT OPERATE REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
WARDS JSJ10625 N/A WILL NOT LOAD -- DRUM WILL NOT RUN CHECK R902 FOR OPEN
WARDS JSJ10625 N/A DEAD - WILL NOT POWER UP CHECK R923
WARDS JSJ10625 N/A INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
WARDS JSJ10625 N/A NO AUDIO IN THE RECORD MODE CHECK/REPLACE Q602 (ECG382) ALSO HARDWIRE ERASE HEADS (FULL AND AUDIO)
WARDS JSJ10625 N/A NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
WARDS JSJ10625 N/A BOTH SERVOS OFF - CAPSTAN IS TOO SLOW AND DRUM IS TOO FAST ALSO NO REW OR FAST FORWARD ALTHOUGH INDICATORS APPEAR. CHECK/REPLACE IC701
WARDS JSJ10625 N/A WILL NOT LOAD CASSETTE REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
WARDS JSJ10625 N/A VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
WARDS JSJ10625 N/A LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE. CHECK/REPLACE IC801
WARDS JSJ10625 N/A CAPSTAN MOTOR WILL NOT OPERATE REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
WARDS JSJ10625 N/A DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY. CHECK/REPLACE Q812 FOR SHORT OR OPEN
WARDS JSJ10658 N/A WILL NOT ERASE AUDIO ON RECORDED TAPES CHECK Q601 AND Q602
WARDS JSJ10660 N/A WILL NOT ERASE AUDIO ON RECORDED TAPES CHECK Q601 AND Q602
WARDS JSJ10660 N/A POOR PIX--LOOKS LIKE ONE HEAD IS MISSING COLD SOLDER JOINT ON LOWER DRUM UNDER VIDEO HEAD
WARDS JSJ10660 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ10660 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ10660 N/A WILL NOT ERASE OLD AUDIO ON A TAPE CHECK Q601 AND Q602 ON THE AUDIO BOARD
WARDS JSJ10662 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ10662 N/A WILL NOT ERASE OLD AUDIO ON A TAPE CHECK Q601 AND Q602 ON THE AUDIO BOARD
WARDS JSJ10662 N/A POOR PIX--LOOKS LIKE ONE HEAD IS MISSING COLD SOLDER JOINT ON LOWER DRUM UNDER VIDEO HEAD
WARDS JSJ10662 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ10664 N/A POOR PIX--LOOKS LIKE ONE HEAD IS MISSING COLD SOLDER JOINT ON LOWER DRUM UNDER VIDEO HEAD
WARDS JSJ10664 N/A WILL NOT ERASE AUDIO ON RECORDED TAPES CHECK Q601 AND Q602
WARDS JSJ10664 N/A WILL NOT ERASE OLD AUDIO ON A TAPE CHECK Q601 AND Q602 ON THE AUDIO BOARD
WARDS JSJ10664 N/A POOR PIX--LOOKS LIKE ONE HEAD IS MISSING COLD SOLDER JOINT ON LOWER DRUM UNDER VIDEO HEAD
WARDS JSJ10664 N/A WILL NOT ERASE OLD AUDIO ON A TAPE CHECK Q601 AND Q602 ON THE AUDIO BOARD
WARDS JSJ10664 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ10664 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ10664 N/A WILL NOT ERASE OLD AUDIO REPLACE Q601,Q602,R602,T601
WARDS JSJ20100 N/A ERRATIC OR INTERMITTENT LOADING/UNLOADING CHECK/REPLACE CAM SWITCH (QSW-R0023GEZZ) - MAY TIMES THIS SWITCH CAN BE OPENED UP AND CLEANED
ZENITH VR1805 N/A ENTERS REWIND FOR A SHORT TIME THEN SHUTS OFF CHECK/REPLACE IC601
ZENITH VR1805 N/A WILL NOT LOAD CASSETTE CHECK CASS DET-2 LEAF SWITCH FOR DIRTY CONTACTS
ZENITH VR1810 N/A INTERMITTENTLY SHUTS OFF OR BLOWS FUSES F2 AND F3 CHECK/REPLACE REEL MOTOR
ZENITH VR1810 N/A TURNS ON BUT POWER LED IS DEAD--FF/REW WORK BUT NO PLAY CHECK/REPLACE IC1 (REGULATOR IC)
ZENITH VR1810 N/A QUIVVER IN SLP AUDIO - SP AND LP ARE NORMAL CHECK/REPLACE IC403
ZENITH VR1810 N/A DEAD-BLOWS FUSES F2 AND F3 WHEN PLAY OR RECORD ARE DEPRESS CHECK/REPLACE LOADING/MODE MOTOR
ZENITH VR1810 N/A CLOCK RESETS INTERMITTENTLY,ESPECIALLY IN THE TIMER MODE. CHECK/REPLACE IC1 (REGULATOR IC)
ZENITH VR1820 N/A QUIVVER IN SLP AUDIO - SP AND LP ARE NORMAL CHECK/REPLACE IC403
ZENITH VR1820 N/A TAPE DAMAGE DUE TO INTERMITTENT CAPSTAN SPEED CHECK/REPLACE C404
ZENITH VR1820 N/A ERRATIC OPERATION,INTERMITTENT FAILURE OF FUSE F3 CHECK CAPACITOR LEAD DRESSING AROUND DELAY LINE
ZENITH VR1820 N/A EATS TAPES CHECK/REPLACE IC604
ZENITH VR1820 N/A INTERMITTENTLY SHUTS OFF OR BLOWS FUSES F2 AND F3 CHECK/REPLACE REEL MOTOR
ZENITH VR1820 N/A TURNS ON BUT POWER LED IS DEAD--FF/REW WORK BUT NO PLAY CHECK/REPLACE IC1 (REGULATOR IC)
ZENITH VR1820 N/A DEAD-BLOWS FUSES F2 AND F3 WHEN PLAY OR RECORD ARE DEPRESS CHECK/REPLACE LOADING/MODE MOTOR
ZENITH VR1820 N/A NO DISPLAY CHECKFOIL CONNECTIONS AT CN1 OF THE MOTHER BOARD BETWEEN CN1 #7 AND CN13 #1 OR CN1 #14 AND CN13 #2
ZENITH VR1820 N/A INTERMITTENT VIDEO RESOLDER CONNECTIONS ON RIBBON CABLE J1
ZENITH VR1820 N/A POWER BUTTON DOESN'T WORK-DRUM WILL NOT RUN REPLACE STK5481 IC
ZENITH VR1825 N/A WILL NOT PLAY-TAPE CAUGHT IN MECHANISM CHECK/REPLACE D606 (SHOULD HAVE A .7V DROP-MAY BE HIGHER IF DEFECTIVE)
ZENITH VR1825 N/A QUIVVER IN SLP AUDIO - SP AND LP ARE NORMAL CHECK/REPLACE IC403
ZENITH VR1830 N/A CHANNEL INDICATOR IS ON,BUT VCR WILL NOT LOAD CASSETTE CHECK D14 (ZENER)
ZENITH VR2000 N/A NO TUNER OPERATION--PLAYS TAPES OK CHECK Q7 ON TUNER/IF BOARD
ZENITH VR2000 N/A PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
ZENITH VR2000 N/A POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP REPLACE CLUTCH ASSEMBLY (861-646-04)
ZENITH VR2100 N/A POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP REPLACE CLUTCH ASSEMBLY (861-646-04)
ZENITH VR2100 N/A PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
ZENITH VR2100 N/A NO DRUM OR CAPSTAN--NO CLOCK DISPLAY CHECK CP1 AND CP2 ON POWER SUPPLY BOARD
ZENITH VR2105 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR2106 N/A UNIT THINKS THERE IS A TAPE IN THE VCR - CARRIAGE TRIES TO LOAD IN/OUT WHEN POWERED UP CHECK/REPLACE S501/S502 (P/N# 921-10046)
ZENITH VR2150 N/A NO TUNER OPERATION--PLAYS TAPES OK CHECK Q7 ON TUNER/IF BOARD
ZENITH VR2150 N/A POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP REPLACE CLUTCH ASSEMBLY (861-646-04)
ZENITH VR2150 N/A PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
ZENITH VR2410 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2410 N/A POOR COLOR - BAD PICTURE - LOOKS LIKE A HUM BAR IN PIX CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2410 N/A ERRATIC OPERATION - GOES TO 'ERR' MODE CLEAN OR REPLACE MODE SELECT SWITCH
ZENITH VR2411 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2412 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2414 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2416 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2420 N/A POOR OR UNSTABLE TRACKING ON SOME RENTAL OR PRE-RECORDED TAPES - SELF RECORDED TAPES USUALLY WORK OK OPEN W2C4 - USE DTC114 XSTR - PUT BASE TO 56 OF IC201,COLL. TO W2C4,EMTR TO GRD., ADD 10K FROM PIN #10 IC201 TO COLL.
ZENITH VR2420 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VR2420HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VR2420HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2421 N/A DISTORTED COLOR ON PLAYBACK CHECK/REPLACE IC101 (6 VOLT REGULATOR)
ZENITH VR2421 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VR2421HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VR2421HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2422 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VR2422 N/A POOR OR UNSTABLE TRACKING ON SOME RENTAL OR PRE-RECORDED TAPES - SELF RECORDED TAPES USUALLY WORK OK OPEN W2C4 - USE DTC114 XSTR - PUT BASE TO 56 OF IC201,COLL. TO W2C4,EMTR TO GRD., ADD 10K FROM PIN #10 IC201 TO COLL.
ZENITH VR2422HF N/A COLOR FADES IN/OUT - HORZ. LINE DISTORTION CHECK/REPLACE IC601 (P/N# HA118019NT)
ZENITH VR2422HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VR2422HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2423 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VR2423HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2423HF N/A COLOR FADES IN/OUT - HORZ. LINE DISTORTION CHECK/REPLACE IC601 (P/N# HA118019NT)
ZENITH VR2423HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VR2424 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VR2424 N/A POOR OR UNSTABLE TRACKING ON SOME RENTAL OR PRE-RECORDED TAPES - SELF RECORDED TAPES USUALLY WORK OK OPEN W2C4 - USE DTC114 XSTR - PUT BASE TO 56 OF IC201,COLL. TO W2C4,EMTR TO GRD., ADD 10K FROM PIN #10 IC201 TO COLL.
ZENITH VR2424HF N/A COLOR FADES IN/OUT - HORZ. LINE DISTORTION CHECK/REPLACE IC601 (P/N# HA118019NT)
ZENITH VR2424HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2424HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VR2426 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VR2426HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VR2426HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VR2426HF N/A COLOR FADES IN/OUT - HORZ. LINE DISTORTION CHECK/REPLACE IC601 (P/N# HA118019NT)
ZENITH VR3000 N/A POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP REPLACE CLUTCH ASSEMBLY (861-646-04)
ZENITH VR3000 N/A NO TUNER OPERATION--PLAYS TAPES OK CHECK Q7 ON TUNER/IF BOARD
ZENITH VR3000 N/A PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
ZENITH VR3010 N/A POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP REPLACE CLUTCH ASSEMBLY (861-646-04)
ZENITH VR3010 N/A NO TUNER OPERATION--PLAYS TAPES OK CHECK Q7 ON TUNER/IF BOARD
ZENITH VR3010 N/A PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
ZENITH VR3020 N/A PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
ZENITH VR3020 N/A NO TUNER OPERATION--PLAYS TAPES OK CHECK Q7 ON TUNER/IF BOARD
ZENITH VR3020 N/A POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP REPLACE CLUTCH ASSEMBLY (861-646-04)
ZENITH VR3200 N/A NO RECORD CHROMA - PLAYBACK CHROMA PERFECT CHECK CONNECTIONS ON R47 - THE GLUE USE TO HOLD DOWN SURROUNDING COMPONENTS MAY HAVE ATE THRU CONNECTIONS.
ZENITH VR3250 N/A NO RECORD CHROMA - PLAYBACK CHROMA PERFECT CHECK CONNECTIONS ON R47 - THE GLUE USE TO HOLD DOWN SURROUNDING COMPONENTS MAY HAVE ATE THRU CONNECTIONS.
ZENITH VR4105 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4106 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4106 N/A UNIT THINKS THERE IS A TAPE IN THE VCR - CARRIAGE TRIES TO LOAD IN/OUT WHEN POWERED UP CHECK/REPLACE S501/S502 (P/N# 921-10046)
ZENITH VR4125 N/A DURING PLAYBACK, THE VCR WILL STOP AND START TO REWIND OR SEARCH AUTOMATICALLY ADD (4) 4.7k?@ 1/6w ON CONNECTOR P9M01 PINS # 12,13,14 AND 15 - THE OPPOSITE END GOES TO GROUND.
ZENITH VR4125 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4126 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4155 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4155 N/A DURING PLAYBACK, THE VCR WILL STOP AND START TO REWIND OR SEARCH AUTOMATICALLY ADD (4) 4.7k?@ 1/6w ON CONNECTOR P9M01 PINS # 12,13,14 AND 15 - THE OPPOSITE END GOES TO GROUND.
ZENITH VR4156 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE R103 (1 meg?
ZENITH VR4175 N/A DURING PLAYBACK, THE VCR WILL STOP AND START TO REWIND OR SEARCH AUTOMATICALLY ADD (4) 4.7k?@ 1/6w ON CONNECTOR P9M01 PINS # 12,13,14 AND 15 - THE OPPOSITE END GOES TO GROUND.
ZENITH VR4175 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4176 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE R103 (1 meg?
ZENITH VR4205HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4206HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4225HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4225HF N/A DURING PLAYBACK, THE VCR WILL STOP AND START TO REWIND OR SEARCH AUTOMATICALLY ADD (4) 4.7k?@ 1/6w ON CONNECTOR P9M01 PINS # 12,13,14 AND 15 - THE OPPOSITE END GOES TO GROUND.
ZENITH VR4226HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4226HF N/A DEAD CHECK/REPLACE RP20 (2.7?@ 2 WATT) AND CP09 (100uF @ 200V)
ZENITH VR4255HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4255HF N/A DURING PLAYBACK, THE VCR WILL STOP AND START TO REWIND OR SEARCH AUTOMATICALLY ADD (4) 4.7k?@ 1/6w ON CONNECTOR P9M01 PINS # 12,13,14 AND 15 - THE OPPOSITE END GOES TO GROUND.
ZENITH VR4256HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE R103 (1 meg?
ZENITH VR4275HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VR4276HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE R103 (1 meg?
ZENITH VR6000 N/A DEAD - NO FUNCTIONS WORK CHECK/REPLACE ICP CP1
ZENITH VRC2105 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC2106 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC2125 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4105 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4125 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4165 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4195 N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4205HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4225HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4265HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRC4275HF N/A DEAD - NO FUSES BLOWN CHECK/REPLACE RP03 (1 meg?
ZENITH VRD100 N/A DEAD - NO +5V OR +12V CHECK/REPLACE IC801
ZENITH VRE150 N/A NO POWER LED - SHOWS THAT A TAPE IS PRESENT WHEN NO TAPE IS INSERTED. +5 OR +12 VOLTS MISSING CHECK/REPLACE REGULATOR IC (STK5474)
ZENITH VRE150 N/A DRUM MOTOR WILL NOT RUN CHECK/REPLACE IC601 (TP602 DRUM ON SHOULD BE HIGH WHEN IN PLAY)
ZENITH VRE150 N/A REEL MOTOR RUNS FOR 5-10 SECONDS THEN POWER GOES OFF CHECK/REPLACE IC602 AND IC604
ZENITH VRE155 N/A NO POWER LED - SHOWS THAT A TAPE IS PRESENT WHEN NO TAPE IS INSERTED. +5 OR +12 VOLTS MISSING CHECK/REPLACE REGULATOR IC (STK5474)
ZENITH VRE155 N/A REEL MOTOR RUNS FOR 5-10 SECONDS THEN POWER GOES OFF CHECK/REPLACE IC602 AND IC604
ZENITH VRE200 N/A DRUM MOTOR OR CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE STK5474 REGULATOR IC
ZENITH VRE205 N/A DRUM MOTOR OR CAPSTAN MOTOR WILL NOT RUN CHECK/REPLACE STK5474 REGULATOR IC
ZENITH VRE510HF N/A TAPE STUCK - NO FUNCTIONS WORK CHECK/REPLACE STK5490 (P/N# 905-1952)
ZENITH VRF250 N/A EATS TAPE OR LEAVES SLACK IN TAPE WHEN GOING TO STOP OR EJECT CLEAN MODEL SELECT SWITCH ON BOTTOM SIDE OF UNIT
ZENITH VRF250 N/A PRESS PLAY,VCR MAY SHOW A NORMAL PICTURE,HALF PICTURE AND HALF SNOW OR ALL SNOW. PRESS STOP THEN PLAY, MAY WORK FINE. CHECK/REPLACE LOWER DRUM OR STATOR UNIT ON DRUM MOTOR
ZENITH VRF250 N/A DISTORTED AUDIO COMING FROM TUNER CHECK/REPLACE CF1 (CERAMIC FILTER)
ZENITH VRG170 N/A WILL NOT TUNE CHANNELS CHECK/REPLACE R20 (P/N# 863-6525)
ZENITH VRG180 N/A WILL NOT TUNE CHANNELS CHECK/REPLACE R20 (P/N# 863-6525)
ZENITH VRG180 N/A WILL NOT TUNE-ONLY SNOW-MAY BE THERMAL CHECK/REPLACE IC1 (M51366SP) ON TUNING BOARD
ZENITH VRG520HF N/A DEAD - POWER SUPPLY CHIRPS OR SQUEALS CHECK/REPLACE C9,C18,C21 AND C33
ZENITH VRG75 N/A WON'T LOAD TAPE OR EJECT TAPE CHECK/REPLACE IC502 (P/N# BA6209)
ZENITH VRJ210 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ210 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ210 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ214 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ214 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ214 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ220 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ220 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ220 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ220HF N/A HI-FI DROPS OUT IN PLAYBACK - SWITCHES FROM HI-FI TO NORMAL AUDIO AND TO HI-FI AGAIN CHANGE R038 TO 47k,C845 TO 2.2uF @ 50v AND R801 TO 3.3k
ZENITH VRJ2410 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRJ2410 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ410 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ410 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ410 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ411 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ411 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ411 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ412 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ412 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ412 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ413 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ413 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ413 N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ415 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ415 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ420 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ420HF N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ420HF N/A HI-FI DROPS OUT IN PLAYBACK - SWITCHES FROM HI-FI TO NORMAL AUDIO AND TO HI-FI AGAIN CHANGE R038 TO 47k,C845 TO 2.2uF @ 50v AND R801 TO 3.3k
ZENITH VRJ420HF N/A NO VIDEO OR OSD ON PLAYBACK OR TUNER - AUDIO IS FINE CHECK/REPLACE Q074 (2SA1015 OR ECG290A)
ZENITH VRJ420HF N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ422 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ422 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ422HF N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ422HF N/A HI-FI DROPS OUT IN PLAYBACK - SWITCHES FROM HI-FI TO NORMAL AUDIO AND TO HI-FI AGAIN CHANGE R038 TO 47k,C845 TO 2.2uF @ 50v AND R801 TO 3.3k
ZENITH VRJ422HF N/A NO VIDEO OR OSD ON PLAYBACK OR TUNER - AUDIO IS FINE CHECK/REPLACE Q074 (2SA1015 OR ECG290A)
ZENITH VRJ424 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ424 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ424HF N/A NO VIDEO OR OSD ON PLAYBACK OR TUNER - AUDIO IS FINE CHECK/REPLACE Q074 (2SA1015 OR ECG290A)
ZENITH VRJ424HF N/A HI-FI DROPS OUT IN PLAYBACK - SWITCHES FROM HI-FI TO NORMAL AUDIO AND TO HI-FI AGAIN CHANGE R038 TO 47k,C845 TO 2.2uF @ 50v AND R801 TO 3.3k
ZENITH VRJ424HF N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ425 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ425 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ428 N/A BLUE SCREEN WHEN USING TUNER - TAPE PLAYS OK - NO TUNER OPERATION CHECK/REPLACE L718
ZENITH VRJ428 N/A EATS TAPES WHILE MACHINE IS UNLOADING TAPE FROM AROUND HEADS AND EJECTING TAPE FROM MACHINE. CHECK/REPLACE BRACKET ASSY. (P/N# 812-02029)
ZENITH VRJ428HF N/A NO VIDEO OR OSD ON PLAYBACK OR TUNER - AUDIO IS FINE CHECK/REPLACE Q074 (2SA1015 OR ECG290A)
ZENITH VRJ428HF N/A UNIT GOES INTO PLAY THEN SHUTS DOWN CHECK/REPLACE C103 (2200 F @ 25v)
ZENITH VRJ428HF N/A HI-FI DROPS OUT IN PLAYBACK - SWITCHES FROM HI-FI TO NORMAL AUDIO AND TO HI-FI AGAIN CHANGE R038 TO 47k,C845 TO 2.2uF @ 50v AND R801 TO 3.3k
ZENITH VRL2110 N/A WILL NOT LOAD OR UNLOAD TAPE CHECK/REPLACE IC503 (P/N# BA6209N OR BA6219)
ZENITH VRL2110 N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL2110 N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL2110 N/A ERRATIC OPERATION - GOES TO 'ERR' MODE CLEAN OR REPLACE MODE SELECT SWITCH
ZENITH VRL2120 N/A WILL NOT LOAD OR UNLOAD TAPE CHECK/REPLACE IC503 (P/N# BA6209N OR BA6219)
ZENITH VRL2130 N/A WILL NOT LOAD OR UNLOAD TAPE CHECK/REPLACE IC503 (P/N# BA6209N OR BA6219)
ZENITH VRL4110 N/A WILL NOT LOAD OR UNLOAD TAPE CHECK/REPLACE IC503 (P/N# BA6209N OR BA6219)
ZENITH VRL4110 N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4110 N/A ERRATIC OPERATION - GOES TO 'ERR' MODE CLEAN OR REPLACE MODE SELECT SWITCH
ZENITH VRL4120 N/A WILL NOT LOAD OR UNLOAD TAPE CHECK/REPLACE IC503 (P/N# BA6209N OR BA6219)
ZENITH VRL4130 N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4130 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4130 N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4130 N/A WILL NOT LOAD OR UNLOAD TAPE CHECK/REPLACE IC503 (P/N# BA6209N OR BA6219)
ZENITH VRL4132 N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4132 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4132 N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4141 N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4141 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4170 N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4170 N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4170 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4210HF N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4230HF N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4230HF N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4230HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4232HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4232HF N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4232HF N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4241HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4241HF N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRL4270 N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRL4270HF N/A AUTO TRACKING DOESN'T WORK PROPERLY ON RENTAL MOVIES WITH ENCODED VASS SIGNAL - SELF RECORDED TAPES ARE OK REMOVE JUMP. W2C4-ADD 921-2134 XSTR-BASE TO PIN 56 OF IC201 EMIT. TO GRD.-COLL. TO PIN 17 IC202-10k FROM W2H5 TO COLL.
ZENITH VRL4270HF N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRM2120 N/A POOR TRACKING ON SOME PRE-RECORDED TAPES - DOES WORK OK WHEN TRACKED MANUALLY CHANGE R222 TO A 470 AND R223 TO A 1meg
ZENITH VRM2120 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4120 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4130 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4150 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4170 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4220 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4250 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRM4270 N/A UNIT WILL NOT ACCEPT A TAPE CHECK/REPLACE Z102 (15v ZENER)
ZENITH VRS426 N/A COLOR IN PLAYBACK FADES IN AND OUT CHECK/REPLACE IC601 (P/N# HA118019NT) IN PRE-AMP
ZENITH VRS426HF N/A PLAYS TAPES IN HIGH SPEED AND WITH NO CHROMA - PICTURE IS FINE IN THE PAUSE MODE CHECK/REPLACE C221 (.1uF @ 50v)
ZENITH VRS426HF N/A DEAD - NO POWER CHECK/REPLACE IC101 REGULATOR IC
ZENITH VRS426HF N/A COLOR FADES IN/OUT - HORZ. LINE DISTORTION CHECK/REPLACE IC601 (P/N# HA118019NT)
LAMSON Digital Electronics
Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines
TEL:00632-2559675  TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810
E-mail:lamsonsm@gmail.com   

YAHOO MESSENGER ID : myrna_q_ng or saishu_ng
SKYPE ID: myrna_q_ng or saishu_ng

(old) Lamson Importers & Exporters Trading

<We will not be using the old address and phone no. in the future. Please be noted when calling us, sending letters, parcels or buying our products>
OLD Address: 681 Carmen Building, Ronquillo St. Quiapo, Manila, Philippines
Phone:00632-7332936 7332940
Fax:00632-7332940 E-mail: