VCR REPAIR TIPS PAGE 7

MAKE	MODEL	CHASSIS	SYMPTOM	CURE
SHARP	VC1106U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC1106U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VC207U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VC2200	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC2200U	N/A	VERT. JITTER OR ROLL IN E-E SIGNAL MODE	ADD 0.1uF ACROSS C005 INSIDE IF PACK
SHARP	VC2200U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC2200U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC2200U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC2208	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC2208U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VC2208U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VC2208U	N/A	ONLY PLAYS SP SPEED-ALL OTHERS ARE TOO FAST	CHECK/REPLACE IC701 (RH-IX0430GEZZ)
SHARP	VC2208U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC2208U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC2208U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC2208U	N/A	WON'T LOAD OR EJECT - MOTORS WILL NOT RUN	CHECK/REPLACE R902
SHARP	VC2210	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC2210U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC2210U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC2210U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC2220	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC2220U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC2220U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC2220U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC2230	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC2230U	N/A	DRUM AND CAPSTAN SPEEDS ARE BOTH TOO SLOW	CHECK/REPLACE R746 OR R747 IN 2.5v REF. CIRCUIT
SHARP	VC2230U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC2230U	N/A	WON'T TAKE OR EJECT A TAPE	CLEAN/REPLACE CAM SWITCH (QSW-R0023GEZZ)
SHARP	VC2230U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC2230U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC3500	N/A	REEL DRIVE MOTOR WILL NOT RUN	CHECK Q8003
SHARP	VC381U	N/A	TAPE PLAYS VERY FAST - ALL SPEEDS	ADJUST PINCH ROLLER ASSEMBLY
SHARP	VC481U	N/A	GOES TO STOP MODE AFTER 5-10 SECONDS IN ALL MODES	CHECK IC802 AND CHANGE R816 TO A 56k
SHARP	VC481U	N/A	PLAYBACK LED ON CONTINUOUSLY-NO TUNER OPERATION-NO E-E OR V-V SWITCHING- STUCK IN V-V MODE	CHECK/REPLACE IC802 (IR2403)
SHARP	VC482U	N/A	CLOCK RUN TOO FAST	CHECK OSC. FREQ. FOR 500KHz.-IF FREQ IS HIGH CHECK TO SEE IF R5006 IS 220 AND R5007 IS 56k
SHARP	VC5206U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC5206U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC5220	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC5220U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC5220U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC581U	N/A	TAPE PLAYS VERY FAST - ALL SPEEDS	ADJUST PINCH ROLLER ASSEMBLY
SHARP	VC582U	N/A	WILL NOT ERASE OLD AUDIO	REPLACE Q601,Q602,R602,T601
SHARP	VC583U	N/A	WILL NOT ERASE AUDIO ON RECORDED TAPES	CHECK Q601 AND Q602
SHARP	VC583U	N/A	WILL NOT ERASE OLD AUDIO	REPLACE Q601,Q602,R602,T601
SHARP	VC583U	N/A	WILL NOT ERASE OLD AUDIO ON A TAPE	CHECK Q601 AND Q602 ON THE AUDIO BOARD
SHARP	VC583UB	N/A	POOR PIX--LOOKS LIKE ONE HEAD IS MISSING	COLD SOLDER JOINT ON LOWER DRUM UNDER VIDEO HEAD
SHARP	VC583UB	N/A	WILL NOT ERASE OLD AUDIO	REPLACE Q601,Q602,R602,T601
SHARP	VC585U	N/A	WILL NOT ERASE OLD AUDIO	REPLACE Q601,Q602,R602,T601
SHARP	VC6608	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6608U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VC6608U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC6608U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VC6608U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC6610	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6610U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC6610U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC6610U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC6630	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6630U	N/A	WON'T TAKE OR EJECT A TAPE	CLEAN/REPLACE CAM SWITCH (QSW-R0023GEZZ)
SHARP	VC6630U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC6630U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VC6630U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VC6730U	N/A	POOR PIX-LOOKS LIKE ONE HEADS NOT WORKING-INTM.	REPLACE DRUM MOTOR--CHECK CONN. WHERE AMP.PLUGS IN
SHARP	VC6730U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC682	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC682U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC682U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC6833	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6833U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC6833U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC683U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC684	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6846	N/A	WILL NOT ACCEPT TAPE	CHECK FOR BROKEN OR BENT LOADING SWITCH
SHARP	VC6846	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6846U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC6846U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC6846UB	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC6846US	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC6847	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6847U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC6847U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC684U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC684U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC685	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC6854U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC685U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC686	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC686U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC687	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC687U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7842U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC7842U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7842U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC7842U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7842U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC7843U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7843U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7844U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC7844U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC7844U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7844U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7844U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC7846U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7846U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC785	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC7854	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC7854U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC7854U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC7854U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC7854U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7855U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7855U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7857	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC7857U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7857U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC7857U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC7857U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC785U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC785U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC785U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC785U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC785U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7864U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC7864U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC7864U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7864U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC7864U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC787	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC787U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC787U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC787U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC787U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC787U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC797	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC7977	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC7977U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC7977U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC7977U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC7977U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC7977U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC797U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC797U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC797U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC797U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC797U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC798	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC798U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC798U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC798U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC798U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC799	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VC7995U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC7995U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VC799U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VC799U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VC799U	N/A	NO VIDEO ON TUNER OR TAPE	CHECK/REPLACE C222 OR D203 FOR SHORT
SHARP	VC799U	N/A	NO PLAYBACK VIDEO (BLACK RASTER) - TUNER VIDEO IS NORMAL	CHECK/REPLACE C409 FOR SHORT
SHARP	VC8870U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA102U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VCA102U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCA102U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA102U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA103U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCA103U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA103U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VCA103U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA105	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA105U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA105U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA105U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA105U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VCA105U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA105U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCA201	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA201U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA201U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA201U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCA201U	N/A	VERT. JITTER OR ROLL IN E-E SIGNAL MODE	ADD 0.1uF ACROSS C005 INSIDE IF PACK
SHARP	VCA201U	N/A	WON'T REWIND OR FAST FORWARD OR PLAY	REPLACE IDLER ASSEMBLY (NPLY0102GEZZ)
SHARP	VCA201U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VCA205	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA205U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA205U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA205U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA206	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA206U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA206U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA206U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA206U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA207	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA207U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA207U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA207U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCA207U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA207U	N/A	WILL NOT LOAD -- DRUM WILL NOT RUN	CHECK R902 FOR OPEN
SHARP	VCA207U	N/A	DEAD - WILL NOT POWER UP	CHECK R923
SHARP	VCA207U	N/A	BOTH SERVOS OFF - CAPSTAN IS TOO SLOW AND DRUM IS TOO FAST ALSO NO REW OR FAST FORWARD ALTHOUGH INDICATORS APPEAR.	CHECK/REPLACE IC701
SHARP	VCA207U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA207U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VCA207U	N/A	NO AUDIO IN THE RECORD MODE	CHECK/REPLACE Q602 (ECG382) ALSO HARDWIRE ERASE HEADS (FULL AND AUDIO)
SHARP	VCA210	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA210U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA210U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA210U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA210U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA220	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA220U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA220U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA220U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA220U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA230	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA230U	N/A	WON'T TAKE OR EJECT A TAPE	CLEAN/REPLACE CAM SWITCH (QSW-R0023GEZZ)
SHARP	VCA230U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA230U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA230U	N/A	DRUM AND CAPSTAN SPEEDS ARE BOTH TOO SLOW	CHECK/REPLACE R746 OR R747 IN 2.5v REF. CIRCUIT
SHARP	VCA230U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA230U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA303U	N/A	REW/FF IS OK BUT UNIT SHUTS OFF IMMEDIATELY AFTER LOADING COMPLETES WHEN GOING TO PLAY MODE	CHECK/REPLACE D906,R903 AND R904
SHARP	VCA323U	N/A	UNIT IS DEAD WITH A BLOWN AC LINE FUSE	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), IC901 (RH-FX0002GEZZ) AND D905 (VHD1SS147//-1)
SHARP	VCA323U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA323U	N/A	DEAD - BLOWS F901	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), AND F901 (QFS-B1625CEZZ)
SHARP	VCA323U	N/A	DEAD - BLOWN FUSE - EXCESSIVE SECONDARY VOLTAGES AFTER REGULATOR AND DUTY CYCLE TRANSISTORS REPLACED	CHECK/REPLACE D907 (LEAKY OR SHORTED) (P/N# VHD1SS147//-1) OR ECG587
SHARP	VCA343U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA353U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCA353U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA353U	N/A	DEAD SET - UNIT BLOWS AC LINE FUSE	CHECK/REPLACE D908 (ECG587), Q901 (2SC4418), F901 (2A GMA)
SHARP	VCA500	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA500U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	CHECK Q602,R629-HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CRKT.ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT
SHARP	VCA500U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCA500U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VCA500U	N/A	DEAD - WILL NOT POWER UP	CHECK D906,D907 AND R912
SHARP	VCA500U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA503U	N/A	REW/FF IS OK BUT UNIT SHUTS OFF IMMEDIATELY AFTER LOADING COMPLETES WHEN GOING TO PLAY MODE	CHECK/REPLACE D906,R903 AND R904
SHARP	VCA504U	N/A	REW/FF IS OK BUT UNIT SHUTS OFF IMMEDIATELY AFTER LOADING COMPLETES WHEN GOING TO PLAY MODE	CHECK/REPLACE D906,R903 AND R904
SHARP	VCA5206	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA5206U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA5210	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA5210U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA5210U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA5220U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA522U	N/A	UNIT IS DEAD WITH A BLOWN AC LINE FUSE	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), IC901 (RH-FX0002GEZZ) AND D905 (VHD1SS147//-1)
SHARP	VCA522U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA522U	N/A	DEAD - BLOWN FUSE - EXCESSIVE SECONDARY VOLTAGES AFTER REGULATOR AND DUTY CYCLE TRANSISTORS REPLACED	CHECK/REPLACE D907 (LEAKY OR SHORTED) (P/N# VHD1SS147//-1) OR ECG587
SHARP	VCA522U	N/A	DEAD - BLOWS F901	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), AND F901 (QFS-B1625CEZZ)
SHARP	VCA5230U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA5230U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA523U	N/A	DEAD - BLOWN FUSE - EXCESSIVE SECONDARY VOLTAGES AFTER REGULATOR AND DUTY CYCLE TRANSISTORS REPLACED	CHECK/REPLACE D907 (LEAKY OR SHORTED) (P/N# VHD1SS147//-1) OR ECG587
SHARP	VCA523U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA523U	N/A	DEAD - BLOWS F901	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), AND F901 (QFS-B1625CEZZ)
SHARP	VCA523U	N/A	UNIT IS DEAD WITH A BLOWN AC LINE FUSE	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), IC901 (RH-FX0002GEZZ) AND D905 (VHD1SS147//-1)
SHARP	VCA524U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA525U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA527U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA542U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA543U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA543U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA544U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA544U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA545U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA545U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA546U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA546U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA548U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA548U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA552U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCA552U	N/A	DEAD SET - UNIT BLOWS AC LINE FUSE	CHECK/REPLACE D908 (ECG587), Q901 (2SC4418), F901 (2A GMA)
SHARP	VCA552U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA554U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCA554U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA554U	N/A	DEAD SET - UNIT BLOWS AC LINE FUSE	CHECK/REPLACE D908 (ECG587), Q901 (2SC4418), F901 (2A GMA)
SHARP	VCA555U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA555U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCA555U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA555U	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1103GEN6)
SHARP	VCA556U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA556U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA556U	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1103GEN6)
SHARP	VCA556U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCA558U	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1103GEN6)
SHARP	VCA558U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCA558U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCA5610	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA5610U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA5610U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA5610U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA5630	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA5630U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA5630U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA5630U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA5640U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA5640U	N/A	WILL NOT REW/FF/PLAY OR EJECT - MANUALLY UNLOADING TAPE AND RE-INSERTING, UNIT WILL PLAY,PRESS STOP-THEN TAPE STUCK	CHECK/REPLACE Q508 (P/N# 2SC2001(LK) )
SHARP	VCA5641U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA5650U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA600U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA600U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCA600U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA600U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VCA601U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCA601U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA601U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA601U	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	VCA607	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA607U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCA607U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA607U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA607U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA607U	N/A	BOTH SERVOS OFF - CAPSTAN IS TOO SLOW AND DRUM IS TOO FAST ALSO NO REW OR FAST FORWARD ALTHOUGH INDICATORS APPEAR.	CHECK/REPLACE IC701
SHARP	VCA607U	N/A	NO AUDIO IN THE RECORD MODE	CHECK/REPLACE Q602 (ECG382) ALSO HARDWIRE ERASE HEADS (FULL AND AUDIO)
SHARP	VCA607U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA607U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VCA610	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA610U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA610U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA610U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA610U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA630	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA630U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA630U	N/A	WON'T TAKE OR EJECT A TAPE	CLEAN/REPLACE CAM SWITCH (QSW-R0023GEZZ)
SHARP	VCA630U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA630U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCA630U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCA670	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA670U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCA670U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA6730	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCA6730U	N/A	LOADING MOTOR WON'T SHUT OFF AFTER TAPE IS LOADED INTO MACHINE.	CHECK/REPLACE IC801
SHARP	VCA6730U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCD75U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCD800U	N/A	WASHED OUT OR WEAK VIDEO	CHECK/REPLACE IC902 (P/N# 95KUCZ0097ZZ)
SHARP	VCG960U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCG960U	N/A	DRUM MOTOR AND CAPSTAN MOTOR WILL NOT RUN ON ANY FUNCTION ALTHOUGH LED DISPLAY SHOWS NORMAL ACTIVITY.	CHECK/REPLACE Q812 FOR SHORT OR OPEN
SHARP	VCG960U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCG960U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCG960U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VCG980U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCG980U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCG980U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VCG980U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCG990U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCH100U	N/A	TAPE WILL NOT LOAD OR UNLOAD PROPERLY	CHECK/REPLACE LOAD GEAR WITH NEW STYLE (P/N# NGERH1227GEZZ)
SHARP	VCH857U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCH857U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCH857U	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	VCH857U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCH860U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCH870U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCH890U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCH903U	N/A	CAPSTAN SPEED IS OFF -- AUTO-TRACKING STAYS ON CONTINUOUS	CHECK/REPLACE SERVO IC (P/N# RH-IX0729GEZZ)
SHARP	VCH922U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH922U	N/A	DEAD - BLOWS F901	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), AND F901 (QFS-B1625CEZZ)
SHARP	VCH922U	N/A	DEAD - BLOWN FUSE - EXCESSIVE SECONDARY VOLTAGES AFTER REGULATOR AND DUTY CYCLE TRANSISTORS REPLACED	CHECK/REPLACE D907 (LEAKY OR SHORTED) (P/N# VHD1SS147//-1) OR ECG587
SHARP	VCH922U	N/A	UNIT IS DEAD WITH A BLOWN AC LINE FUSE	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), IC901 (RH-FX0002GEZZ) AND D905 (VHD1SS147//-1)
SHARP	VCH922U	N/A	TAPE WILL NOT LOAD OR UNLOAD PROPERLY	CHECK/REPLACE LOAD GEAR WITH NEW STYLE (P/N# NGERH1227GEZZ)
SHARP	VCH923U	N/A	DEAD - BLOWS F901	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), AND F901 (QFS-B1625CEZZ)
SHARP	VCH923U	N/A	DEAD - BLOWN FUSE - EXCESSIVE SECONDARY VOLTAGES AFTER REGULATOR AND DUTY CYCLE TRANSISTORS REPLACED	CHECK/REPLACE D907 (LEAKY OR SHORTED) (P/N# VHD1SS147//-1) OR ECG587
SHARP	VCH923U	N/A	TAPE WILL NOT LOAD OR UNLOAD PROPERLY	CHECK/REPLACE LOAD GEAR WITH NEW STYLE (P/N# NGERH1227GEZZ)
SHARP	VCH923U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH923U	N/A	UNIT IS DEAD WITH A BLOWN AC LINE FUSE	CHECK/REPLACE Q901 (VS2SC4273//-1), Q902 (VS2SD2144S/-1), IC901 (RH-FX0002GEZZ) AND D905 (VHD1SS147//-1)
SHARP	VCH925U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH925U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH925U	N/A	TAPE WILL NOT LOAD OR UNLOAD PROPERLY	CHECK/REPLACE LOAD GEAR WITH NEW STYLE (P/N# NGERH1227GEZZ)
SHARP	VCH927U	N/A	TAPE WILL NOT LOAD OR UNLOAD PROPERLY	CHECK/REPLACE LOAD GEAR WITH NEW STYLE (P/N# NGERH1227GEZZ)
SHARP	VCH927U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH934U	N/A	TAPE WILL NOT LOAD OR UNLOAD PROPERLY	CHECK/REPLACE LOAD GEAR WITH NEW STYLE (P/N# NGERH1227GEZZ)
SHARP	VCH942U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH943U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH943U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH944U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH944U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH945U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH945U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH946U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH946U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH948U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH948U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH952U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCH952U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH952U	N/A	DEAD SET - UNIT BLOWS AC LINE FUSE	CHECK/REPLACE D908 (ECG587), Q901 (2SC4418), F901 (2A GMA)
SHARP	VCH953U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCH953U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH953U	N/A	DEAD SET - UNIT BLOWS AC LINE FUSE	CHECK/REPLACE D908 (ECG587), Q901 (2SC4418), F901 (2A GMA)
SHARP	VCH954U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCH954U	N/A	DEAD SET - UNIT BLOWS AC LINE FUSE	CHECK/REPLACE D908 (ECG587), Q901 (2SC4418), F901 (2A GMA)
SHARP	VCH954U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH955U	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1103GEN6)
SHARP	VCH955U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH955U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH955U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCH956U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH956U	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1103GEN6)
SHARP	VCH956U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCH956U	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	VCH958U	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1103GEN6)
SHARP	VCH958U	N/A	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE IC901 (P/N# RH-FX0002GEZZ)
SHARP	VCH958U	N/A	DRUM MOTOR WON'T RUN	CHECK/REPLACE IC951 (LM7809 - 9 VOLT REGULATOR)
SHARP	VCM705	N/A	NO TUNER VIDEO BUT PLAYBACK VIDEO IS OK	CHECK/CLEAN VIDEO INPUT JACK (VIDEO SWITCH)
SHARP	VCM705U	N/A	WILL NOT LOAD CASSETTE	REPLACE START SENSOR AND CASSETTE SWITCH WITH THE NEW PART NUMBER WHICH CONTAINS BOTH PARTS (DUNTK3194HE00)
SHARP	VCM705U	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	VCM705U	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	VCQ77U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	VCT64U	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	XA101	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	XA101	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	XA101	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	XA200	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	XA200	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	XA200	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	XA205	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	XA205	N/A	DRUM SPEED RUN AWAY - PG PULSES GOOD BUT FG PULSES WEAK	CHECK DRUM MOTOR FOR COLD SOLDER JOINTS,ESPECIALLY THE (2) JUMPERS ATTACHING FG COIL TO CIRCUIT BOARD.
SHARP	XA205	N/A	INTERMITTENT AUDIO-WILL NOT ERASE OLD AUDIO	HARD WIRE ALL CONNECTORS IN THE AUDIO BIAS CIRCUIT SUCH FULL ERASE HEAD,AUDIO/CTRL HEAD AND CBA CONNECT.
SHARP	XA300	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	XA300	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	XA300	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	XA305	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	XA305	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	XA305	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	XA310	N/A	CAPSTAN MOTOR WILL NOT OPERATE	REMOVE C6 FROM CAPSTAN MOTOR CBA,CLEAN CBA,REPL. C6 WITH 94SSEE5131713P,ADD JUMPER FROM C6 (+) TO 'MC' PIN #7
SHARP	XA310	N/A	INTERMITTENT DRUM FG SIGNAL--DRUM RUN AWAY THEN SHUTS DOWN	CHECK PIN 6 OF IC701 FOR SINE WAVE-IF MISSING REPL. THE DRUM MOTOR (RMOTP1096GEZZ)
SHARP	XA310	N/A	VIDEO HAS A HUM BAR ROLLING THROUGH THE PIX OF A RECORDING	CHECK/REPLACE THE RECTIFIERS IN THE 9 VOLT SUPPLY.
SHARP	XA605	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1113GEN2)
SHARP	XA605A	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	XA610	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1113GEN2)
SHARP	XA610A	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHARP	XA620	N/A	WHEN USING T60 OR T80 TAPES WITH A SMALL HUB, THE HIGH SPEED REWIND AND FAST FORWARD NOT WORKING	CHECK/REPLACE IC701 (P/N# RH-IX1113GEN2)
SHARP	XA620A	N/A	EXCESSIVE TAPE SLACK AFTER REWINDING OR FAST FORWARDING	CHECK/REPLACE TAKE UP BRAKE PAD (P/N3 MLEVP0280AJZZ)
SHINTOM	VP3550N	N/A	NO SOUND ON PLAYBACK - VIDEO IS FINE	CHECK/REPLACE Q113 OPEN
SONY	EVS3000	N/A	UNIT WILL ACCEPT TAPE BUT INTERMITTENTLY NOT THREAD IT AND THEN POWER WOULD SHUT OFF.	CHECK/RESOLDER CONNECTIONS ON IC405
SONY	EVS3000	N/A	NO REMOTE CONTROL OPERATION	CHECK/REPLACE IC005
SONY	EVS7000	N/A	HIGH TAPE TORQUE OR VCR BREAKS TAPES	CHECK/REPLACE REEL TABLE ASSY. (P/N# X-3942-953-2)
SONY	EVS7000	N/A	BRAKE PADS ON BRAKING LEVERS ARE PEELING OFF	CHECK/REPLACE WITH NEW TYPE (P/N# X-3943-161-2)
SONY	GVM20	N/A	FUSE PS-801 OR PS-802 BLOWS WHEN USING IN A VEHICLE	CHECK/REPLACE WITH A 2A FUSE (P/N# 1-533-282-21)
SONY	GVS50	N/A	FUSE PS-401 OR PS-402 BLOWS WHEN USING IN A VEHICLE	CHECK/REPLACE WITH A 2A FUSE (P/N# 1-533-282-21)
SONY	SLHF2100	N/A	AUDIO BUZZ WHEN CONNECTED TO AN AUDIO/VIDEO TV SYSTEM	REMOVE JW108 AND JW109 ON THE 'PS-253' BOARD - C801 MAY NOT BE INSTALLED, IF NOT ADD 4700uF@25v,TIGHTEN PWR.SUP.GROUNDS
SONY	SLHF2100	N/A	POOR PICTURE ON PLAYBACK - GRAINY WITH CHROMA NOISE	CHECK/REPLACE IC403
SONY	SLHF360	N/A	PICTURE ROLLS IN PLAYBACK	CHECK/REPLACE C057 FOR LEAKAGE
SONY	SLHF840D	N/A	TAPE PARTIALLY LOADS THEN EJECTS	CHECK/REPLACE CAPSTAN MOTOR
SONY	SLV272	N/A	DEW SENSOR COMES ON INTERMITTENT	CHECK/RESOLDER CONNECTIONS ON CONNECTOR CN821 ON MC-3 BOARD
SONY	SLV340	N/A	NO DISPLAY	CHECK/REPLACE L181
SONY	SLV340	N/A	TAPE GOES INTO MACHINE BUT WILL NOT THREAD AROUND HEADS	CHECK/REPLACE LOADING GEAR (P/N# 3-958-485-02) AND MAIN SLIDER (P/N# 3-958-163-04)
SONY	SLV340HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV353	N/A	CAPSTAN TURNS VERY SLOWLY WHEN UNIT SHUTS DOWN	CHECK/REPLACE DEFECTIVE ARM LIMITER ( SEE p.106 IN MANUAL )
SONY	SLV353	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV353UC	N/A	VCR SHUTS OFF DURING PLAYBACK/REVIEW MODE AND LOCKS UP	REPLACE REEL SENSOR PH001,PH002 ON MD-22 BD.-ADD 2 6.2V ZENERS WITH CATHODES TO PIN#4,ANODESS TO PIN#3
SONY	SLV360	N/A	WON'T LOAD/UNLOAD TAPES	CHECK/REPLACE CARRIAGE #151 (P/N# A-6751-496-C) AND FRONT LOAD DRIVE GEAR #262 (P/N3 3-958-156-02)
SONY	SLV373	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV373UC	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV373UC	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLV373UC	N/A	CLOCK RUNS TOO FAST	CHECK/REPLACE TIMER IC WITH NEW TYPE (P/N# 8-752-837-77)
SONY	SLV373UC	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV390	N/A	WON'T LOAD/UNLOAD TAPES	CHECK/REPLACE CARRIAGE #151 (P/N# A-6751-496-C) AND FRONT LOAD DRIVE GEAR #262 (P/N3 3-958-156-02)
SONY	SLV393	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV393	N/A	NO TUNER VIDEO - BLUE SCREEN	CHECK/REPLACE IC102 (P/N# 8-759-927-56)
SONY	SLV393	N/A	EATS TAPES AND CAPSTAN MOTOR RUNS BACKWARDS	CHECK/REPLACE IC004
SONY	SLV393UC	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV393UC	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV393UC	N/A	CLOCK RUNS TOO FAST	CHECK/REPLACE TIMER IC WITH NEW TYPE (P/N# 8-752-837-84) AND SHORT R003 ON THE MF-149 BOARD
SONY	SLV393UC	N/A	POOR VIDEO ON PLAYBACK	CHECK/RESOLDER CONNECTIONS ON CRYSTAL UC-1 ON 'Y/C' BOARD
SONY	SLV400	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV400	N/A	OSD MAY JITTER ON CERTAIN TV SETS	CHANGE IC201 TO (P/N# 8-759-257-69)
SONY	SLV420	N/A	UNIT LOCKS UP IN THE EJECT MODE	ADD 0.047uF ACROSS CASSETTE OUT SWITCH ON THE CARRIAGE (P/N# 1-161-021-00)
SONY	SLV440	N/A	TAPE GOES INTO MACHINE BUT WILL NOT THREAD AROUND HEADS	CHECK/REPLACE LOADING GEAR (P/N# 3-958-485-02) AND MAIN SLIDER (P/N# 3-958-163-04)
SONY	SLV440HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV555	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV555UC	N/A	DEAD SET - POWER SUPPLY FAILURE	CHECK/REPLACE C109 AND D207
SONY	SLV555UC	N/A	VCR SHUTS OFF DURING PLAYBACK/REVIEW MODE AND LOCKS UP	REPLACE REEL SENSOR PH001,PH002 ON MD-22 BD.-ADD 2 6.2V ZENERS WITH CATHODES TO PIN#4,ANODESS TO PIN#3
SONY	SLV575	N/A	TICKING NOISE DURING PLAYBACK	RESET SPRING #213 INTO HOLDER #203
SONY	SLV575	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV575	N/A	UNIT LOADS TAPE BUT NO OTHER FUNCTIONS WORK	CHECK/REPLACE IC501
SONY	SLV575	N/A	NO E-E OR PLAYBACK VIDEO	CHECK/RESOLDER CONNECTIONS ON IC004
SONY	SLV575	N/A	NO VIDEO ON PLAYBACK OR E-E VIDEO - AUDIO IS OK	CHECK/REPLACE IC4 (P/N# BA178M05) ON YC-59 BOARD
SONY	SLV575HF	N/A	SHUTS OFF INTERMITTENTLY ON ALL FUNCTIONS	CHECK/REPLACE PH01/PH02 (P/N# 8-759-144-33) REEL SENSOR
SONY	SLV575UC	N/A	LOSS OF SOUND AFTER ON FOR AWHILE	CHECK/REPLACE IC006
SONY	SLV575UC	N/A	NO VIDEO ON PLAYBACK - AUDIO IS FINE	CHECK/REPLACE IC4 ON 'YC59' BOARD (P/N# BA178M05)
SONY	SLV575UC	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLV575UC	N/A	NO OSD	CHECK/REPLACE IC851 (P/N# M50554-182SP)
SONY	SLV585	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV585	N/A	NO E-E OR PLAYBACK VIDEO	CHECK/RESOLDER CONNECTIONS ON IC004
SONY	SLV585	N/A	UNIT LOADS TAPE BUT NO OTHER FUNCTIONS WORK	CHECK/REPLACE IC501
SONY	SLV585	N/A	TICKING NOISE DURING PLAYBACK	RESET SPRING #213 INTO HOLDER #203
SONY	SLV585HF	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV585HF	N/A	CLOCK RUNS TOO FAST	CHECK/REPLACE TIMER IC WITH NEW TYPE (P/N# 8-752-837-83)
SONY	SLV585HF	N/A	AFTER UNIT WARMS UP, TAPE WOULD STOP AND START - COUNTER KEEPS WORKING	CHECK/REPLACE CAPSTAN MOTOR
SONY	SLV585HF	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLV585HF	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV585HF	N/A	NO COLOR ON SELF RECORDED TAPES OR PICTURE HAS RED TINT ON PRE-RECORDED TAPES	CHECK/REPLACE C048 (0.047uF) (P/N# 1-163-809-11)
SONY	SLV585HF	N/A	ERRATIC OPERATION	CHECK/REPLACE MODE SELECT SWITCH (P/N# 1-692-062-11)
SONY	SLV585HF	N/A	SHUTS OFF INTERMITTENTLY ON ALL FUNCTIONS	CHECK/REPLACE PH01/PH02 (P/N# 8-759-144-33) REEL SENSOR
SONY	SLV585UC	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLV586	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV586HF	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV586HF	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV595	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV595	N/A	AUDIO DROPOUT OR AUDIO POPS	CHECK/REPLACE IC502 (P/N# 8-752-840-30)
SONY	SLV595HF	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV595HF	N/A	RANDOM AUDIO POP OR DROP OUT ON THE PLAYBACK OF RECORDINGS	CHECK/REPLACE IC502 WITH NEW VERSION (P/N# 8-752-840-30)
SONY	SLV595HF	N/A	PLAYS TAPE FINE BUT NO E-E VIDEO FROM TUNER,LINE1 OR LINE2	CHECK/REPLACE IC001 ON YC-114 BOARD
SONY	SLV595HF	N/A	DEAD SET OR EXCESSIVE AUDIO AND VIDEO NOISE IN RECORD MODE	CHECK/REPLACE C203
SONY	SLV595HF	N/A	CLOCK RUNS TOO FAST	CHECK/REPLACE TIMER IC WITH NEW TYPE (P/N# 8-752-837-87)
SONY	SLV595HF	N/A	SHUTS OFF INTERMITTENTLY ON ALL FUNCTIONS	CHECK/REPLACE PH01/PH02 (P/N# 8-759-144-33) REEL SENSOR
SONY	SLV595HF	N/A	AUDIO DROPS OUT OR AUDIO POPS	CHECK/REPLACE IC502 (P/N# 8-752-840-30)
SONY	SLV595HF	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV620	N/A	WON'T LOAD TAPE	CHECK/REPLACE IC501 (P/N# 8-752-854-75)
SONY	SLV640	N/A	TAPE GOES INTO MACHINE BUT WILL NOT THREAD AROUND HEADS	CHECK/REPLACE LOADING GEAR (P/N# 3-958-485-02) AND MAIN SLIDER (P/N# 3-958-163-04)
SONY	SLV640HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV640HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLV660HF	N/A	LOADING PROBLEMS	CHECK/RESOLDER CONNECTIONS ON IC501
SONY	SLV660HF	N/A	WON'T LOAD/UNLOAD TAPES	CHECK/REPLACE CARRIAGE #151 (P/N# A-6751-496-C) AND FRONT LOAD DRIVE GEAR #262 (P/N3 3-958-156-02)
SONY	SLV660HF	N/A	TRACKING PROBLEMS AND NOISY ON FAST FORWARD	CHECK FOR BENT TAKE-UP REEL SHAFT
SONY	SLV660HF	N/A	WON'T RECORD OR PLAYBACK	CHECK/RESOLDER CONNECTIONS ON CN201
SONY	SLV660HF	N/A	POOR RECORDING QUALITY	CHECK/RESOLDER CONNECTIONS ON IC ON THE RP195 BOARD
SONY	SLV676	N/A	TICKING NOISE DURING PLAYBACK	RESET SPRING #213 INTO HOLDER #203
SONY	SLV676	N/A	NO E-E OR PLAYBACK VIDEO	CHECK/RESOLDER CONNECTIONS ON IC004
SONY	SLV676	N/A	UNIT LOADS TAPE BUT NO OTHER FUNCTIONS WORK	CHECK/REPLACE IC501
SONY	SLV676	N/A	NO VIDEO ON PLAYBACK OR E-E VIDEO - AUDIO IS OK	CHECK/REPLACE IC4 (P/N# BA178M05) ON YC-59 BOARD
SONY	SLV676	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV676UC	N/A	NO VIDEO ON PLAYBACK - AUDIO IS FINE	CHECK/REPLACE IC4 ON 'YC59' BOARD (P/N# BA178M05)
SONY	SLV676UC	N/A	INTERMITTENT BLUE SCREEN	CHECK/REPLACE INTERMITTENT X301 CRYSTAL
SONY	SLV676UC	N/A	NO TUNER AUDIO BUT SIMULCAST AUDIO IS PRESENT	CHECK/REPLACE Q807
SONY	SLV676UC	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLV676UC	N/A	NO OSD	CHECK/REPLACE IC851 (P/N# M50554-182SP)
SONY	SLV686	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV686HF	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLV686HF	N/A	SHUTS OFF INTERMITTENTLY ON ALL FUNCTIONS	CHECK/REPLACE PH01/PH02 (P/N# 8-759-144-33) REEL SENSOR
SONY	SLV686HF	N/A	NO COLOR ON SELF RECORDED TAPES OR PICTURE HAS RED TINT ON PRE-RECORDED TAPES	CHECK/REPLACE C048 (0.047uF) (P/N# 1-163-809-11)
SONY	SLV686HF	N/A	CLOCK RUNS TOO FAST	CHECK/REPLACE TIMER IC WITH NEW TYPE (P/N# 8-752-837-83)
SONY	SLV690HF	N/A	WON'T LOAD/UNLOAD TAPES	CHECK/REPLACE CARRIAGE #151 (P/N# A-6751-496-C) AND FRONT LOAD DRIVE GEAR #262 (P/N3 3-958-156-02)
SONY	SLV696	N/A	AUDIO DROPOUT OR AUDIO POPS	CHECK/REPLACE IC502 (P/N# 8-752-840-30)
SONY	SLV696	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV696HF	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV696HF	N/A	CLOCK RUNS TOO FAST	CHECK/REPLACE TIMER IC WITH NEW TYPE (P/N# 8-752-837-87)
SONY	SLV696HF	N/A	AUDIO DROPS OUT INTERMITTENT OR AUDIO POPS	CHECK/REPLACE IC502 WITH NEW TYPE (P/N# 8-752-840-30)
SONY	SLV696HF	N/A	SHUTS OFF INTERMITTENTLY ON ALL FUNCTIONS	CHECK/REPLACE PH01/PH02 (P/N# 8-759-144-33) REEL SENSOR
SONY	SLV696HF	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV696HF	N/A	RANDOM AUDIO POP OR DROP OUT ON THE PLAYBACK OF RECORDINGS	CHECK/REPLACE IC502 WITH NEW VERSION (P/N# 8-752-840-30)
SONY	SLV696HF	N/A	AUDIO DROPS OUT OR AUDIO POPS	CHECK/REPLACE IC502 (P/N# 8-752-840-30)
SONY	SLV696HF	N/A	FRONT PANEL CONTROLS DO NOT FUNCTION BUT REMOTE IS OK	SOLDER A WIRE FROM CN903 PIN4 TO PIN6 OF C906 ON THE 'MF-140' BAORD
SONY	SLV700	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV700	N/A	OSD MAY JITTER ON CERTAIN TV SETS	CHANGE IC201 TO (P/N# 8-759-257-69)
SONY	SLV700HF	N/A	EATS TAPES WHEN EJECTING - CAPSTAN WON'T RUN IN REVERSE	RESEAT CONNECTOR CN401
SONY	SLV720	N/A	UNIT LOCKS UP IN THE EJECT MODE	ADD 0.047uF ACROSS CASSETTE OUT SWITCH ON THE CARRIAGE (P/N# 1-161-021-00)
SONY	SLV740	N/A	TAPE GOES INTO MACHINE BUT WILL NOT THREAD AROUND HEADS	CHECK/REPLACE LOADING GEAR (P/N# 3-958-485-02) AND MAIN SLIDER (P/N# 3-958-163-04)
SONY	SLV740HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV740HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLV741HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLV741HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV750	N/A	OSD MAY JITTER ON CERTAIN TV SETS	CHANGE IC101 TO (P/N# 8-759-259-30)
SONY	SLV750	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV750HF	N/A	DEAD SET	CHECK/REPLACE D102
SONY	SLV750HF	N/A	INTERMITTENT LOSS OF VIDEO FROM TUNER	CHECK/RESOLDER CONNECTIONS ON R811,R838 AND Q803
SONY	SLV750HF	N/A	INTERMITTENT LOSS OF VIDEO OR NO VIDEO	CHECK/RESOLDER CONNECTIONS NEAR TUNER - MAYBE HAIR LINE CRACKS-INSTALL RUBBER CUSHION (P/N# 3-957-967-01) AT JW194
SONY	SLV757	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV757UC	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLV757UC	N/A	VCR SHUTS OFF DURING PLAYBACK/REVIEW MODE AND LOCKS UP	REPLACE REEL SENSOR PH001,PH002 ON MD-22 BD.-ADD 2 6.2V ZENERS WITH CATHODES TO PIN#4,ANODESS TO PIN#3
SONY	SLV757UC	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLV75HF	N/A	NO PICTURE IN PLAYBACK, JUST BLACK AND WHITE LINES	CHECK/REPLACE IC801
SONY	SLV760HF	N/A	NO PICTURE	CHECK/REPLACE Q703
SONY	SLV765HF	N/A	LOADS THE TAPE BUT WON'T PLAY, F/F OR REWIND - DRUM MOTOR WON'T SPIN - ERROR CODES L2 OR L3 COME UP	CHECK/RESOLDER CONNECTIONS ON CN275
SONY	SLV770HF	N/A	TAPE STUCK IN UNIT	CHECK/REPLACE M901 LOADING MOTOR (P/N# X-3733-302-1), IC202 AND PS201 (P/N# 1-532-685-00) FOR OPEN
SONY	SLV770HF	N/A	WON'T GO INTO MONO MODE	CHECK/REPLACE IC401 (P/N# 8-759-268-17)
SONY	SLV780	N/A	TAPE GOES INTO MACHINE BUT WILL NOT THREAD AROUND HEADS	CHECK/REPLACE LOADING GEAR (P/N# 3-958-485-02) AND MAIN SLIDER (P/N# 3-958-163-04)
SONY	SLV780HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLV780HF	N/A	WHITE LINES IN PICTURE ON PLAYBACK	CHECK/REPLACE LOWER DRUM (P/N# 8-848-666-11)
SONY	SLV781HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLV900	N/A	OSD MAY JITTER ON CERTAIN TV SETS	CHANGE IC101 TO (P/N# 8-759-259-30)
SONY	SLV900	N/A	VCR EATS TAPES	LUBRICATE FROZEN HALF LOAD TAPE LEVER
SONY	SLV900HF	N/A	INTERMITTENT LOSS OF VIDEO OR NO VIDEO	CHECK/RESOLDER CONNECTIONS NEAR TUNER - MAYBE HAIR LINE CRACKS-INSTALL RUBBER CUSHION (P/N# 3-957-967-01) AT JW194
SONY	SLV900HF	N/A	POOR VIDEO IN THE PAUSE MODE AND SCAN MODE	CHECK THE TENSION ON THE CAPSTAN BELT FOR TOO TIGHT
SONY	SLV920HF	N/A	WON'T GO INTO MONO MODE	CHECK/REPLACE IC401 (P/N# 8-759-268-17)
SONY	SLV940HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV940HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLV980HF	N/A	NO DISPLAY	CHECK/REPLACE CP102 DC-DC CONVERTER (P/N# 1-467-811-12)
SONY	SLV980HF	N/A	TAPE WON'T EJECT	CHECK/REPLACE CARRIAGE ASSY. (P/N# A-6751-496-C)
SONY	SLVR1000	N/A	OSD MAY JITTER ON CERTAIN TV SETS	CHANGE IC401 TO (P/N# 8-759-255-47)
SONY	SLVR5UC	N/A	INTERMITTENT SNOWY PICTURE LIKE DIRTY HEADS	SOLDER THE SHIELDS OF RP76 TOGETHER
SONY	SLVR5UC	N/A	UNIT STOPS AFTER 2 TO 3 HOURS IN REC/PB ON EP IF CAPSTAN FLYWHEEL HAS A U-26B OR U-26D STAMP THEN PROCEED	CHANGE C1 ON CAPSTAN MOTOR TO (P/N# 1-162-638-11) AND C2, C3,C4 TO A (P/N# 1-163-081-00)
SONY	SLVR5UC	N/A	NO PLAYBACK CONTROL - PICTURE WILL NOT LOCK UP	CHECK/REPLACE IC401 OR IC402
SONY	SLVR5UC	N/A	PLAYBACK PICTURE BENDS AND DISTORTS	CHECK/REPLACE IC001 ON THE 'YC105' BOARD
SONY	SLVR5UC	N/A	NO PLAYBACK VIDEO - AUDIO IS OK	CHECK/REPLACE L001
SONY	SLVR5UC	N/A	COLOR NOISE IN PLAYBACK (BOTTOM HALF OF PICTURE)	CHECK/REPLACE RP112 BOARD
SONY	SLVR5UC	N/A	NOISY AUDIO ON THE RIGHT CHANNEL	FOUND R013 CONNECTED BETWEEN R012 AND C012 INSTEAD OF BETWEEN R012 AND GROUND
SONY	SLVR5UC	N/A	UNIT SHUTS DOWN WHEN POWER IS REMOVED FOR A SHORT PERIOD OF TIME AND WILL NOT RESTART - DEAD AFTER POWER IS RE-APPLIED	ADD 270k PARALLEL ACROSS C105 IN POWER SUPPLY
SYLVANIA	LV227G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYLVANIA	LV426G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYLVANIA	LV428HG	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYLVANIA	LV446G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYLVANIA	LV448HG	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYLVANIA	VC2233	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
SYLVANIA	VC2233	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
SYLVANIA	VC2233	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
SYLVANIA	VC2233	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
SYLVANIA	VC2233	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
SYLVANIA	VC2233	N/A	NO FIP LOADING MOTOR ENGAGES OK	CHECK/REPLACE C1020 C1021 L1005
SYLVANIA	VC2233	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
SYLVANIA	VC2233	N/A	DEW INDICATOR ILLUMINATES AND UNIT SHUTS DOWN	LOOSE CONNECTIONS ONTHE P3 PLUG
SYLVANIA	VC2233	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
SYLVANIA	VC2233	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
SYLVANIA	VC2233	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
SYLVANIA	VC2233	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
SYLVANIA	VC2233	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
SYLVANIA	VC2233	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
SYLVANIA	VC2233	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
SYLVANIA	VC2233	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
SYLVANIA	VC2233	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
SYLVANIA	VC2233	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC2233	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
SYLVANIA	VC2233	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
SYLVANIA	VC2233	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
SYLVANIA	VC2233	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
SYLVANIA	VC2233	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
SYLVANIA	VC2233	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
SYLVANIA	VC2233	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
SYLVANIA	VC2233	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
SYLVANIA	VC2234	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
SYLVANIA	VC2234	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
SYLVANIA	VC2234	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
SYLVANIA	VC2234	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
SYLVANIA	VC2234	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
SYLVANIA	VC2234	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
SYLVANIA	VC2234	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
SYLVANIA	VC2234	N/A	DEW INDICATOR ILLUMINATES AND UNIT SHUTS DOWN	LOOSE CONNECTIONS ONTHE P3 PLUG
SYLVANIA	VC2234	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
SYLVANIA	VC2234	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
SYLVANIA	VC2234	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
SYLVANIA	VC2234	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
SYLVANIA	VC2234	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
SYLVANIA	VC2234	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
SYLVANIA	VC2234	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
SYLVANIA	VC2234	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
SYLVANIA	VC2234	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
SYLVANIA	VC2234	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
SYLVANIA	VC2234	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
SYLVANIA	VC2234	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
SYLVANIA	VC2234	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
SYLVANIA	VC2234	N/A	NO FIP LOADING MOTOR ENGAGES OK	CHECK/REPLACE C1020 C1021 L1005
SYLVANIA	VC2234	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC2234	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
SYLVANIA	VC2234	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
SYLVANIA	VC2234	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
SYLVANIA	VC2970	N/A	NO RF OUTPUT RF CONVERTER OK	REPLACE IC701
SYLVANIA	VC2970	N/A	CASSETTE LOAD/UNLOAD AND EJECT OK NO ATTEMPT RUN	CHECK/REPLACE THE SENSOR LED OR21013
SYLVANIA	VC2970	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
SYLVANIA	VC2970	N/A	PLAYS HALF OF TAPE CAPSTAN DRIVE IC HOT	REPLACE CAPSTAN BEARING ASSEMBLY
SYLVANIA	VC2970	N/A	GARBLED AUDIO IN LP AND SLP	CHECK IC4705,PINCH ROLLER,CLUTCH ASSY.;IDLER
SYLVANIA	VC2970	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
SYLVANIA	VC2970	N/A	SWITCHES FROM STOP-PLAY-STOP BACK AND FORTH	CHECK/CLEAN MODE SELECT SWITCH
SYLVANIA	VC2970	N/A	NO POWER NO DISPLAY FUSE OK	CHECK FOR DEFECTIVE Q3 AND D9 IN THE POWER SUPPLY
SYLVANIA	VC2970	N/A	DEAD WITH NO FIP DISPLAY	CHECK/REPLACE IC2005 AND R2087
SYLVANIA	VC2970	N/A	COMPLETELY DEAD	CHECK R1001,R1034,R1006 FOR OPEN CONDITIONS
SYLVANIA	VC2970	N/A	FIP INDCATES PROPER MODE CAPSTAN FAILS TO RUN	CHECK Q2005
SYLVANIA	VC2970	N/A	CHANGES BACK & FORTH FROM PAUSE TO RECORD	REPLACE Q1013
SYLVANIA	VC2970	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
SYLVANIA	VC2970	N/A	IN THE STOP MODE,RECORDING SPEED CANNOT BE SELECTED AND WHEN IN PLAY MODE FIP DISPLAYS LP MODE	CHECK/REPLACE IC4003 ALSO CHECK CONTINUITY OF SPEED SWITCH
SYLVANIA	VC2970	N/A	ERRATIC FUNCTIONS--PLAY>STOP RESULTS PLAY>REWIND	CHECK FOR DIRTY MODE SELECT SWITCH OR SWITCH TIMING.
SYLVANIA	VC2970	N/A	WILL NOT CHANGE CHANNELS WITH REMOTE/DIRECTACCES	CHECK/REPLACE IC7001 & R7037
SYLVANIA	VC2970	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
SYLVANIA	VC2970	N/A	REWINDS DURING PLAY	CHECK OR REPLACE THE MICROPROCESSOR
SYLVANIA	VC2970	N/A	UNIT LOADS TAPE DOES NOT MOVE	REPLACE IC2601
SYLVANIA	VC2970	N/A	WILL NOT CHANGE CHANNELS WITH REMOTE	CHECK/REPLACE IC6003
SYLVANIA	VC2970	N/A	POWER SHUTS OFF AFTER EJECTING TAPE	CHECK CASSETTE IN SWITCH
SYLVANIA	VC2970	N/A	ERRATIC COUNTER OPERATION	CHECK/CLEAN THE REFLECTIVE SURFACE ON BOTTOM SIDE OF TAKE UP REEL
SYLVANIA	VC2970	N/A	INCORRECT CAPSTAN SPEED	CHECK/REPLACE IC6001
SYLVANIA	VC3145	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
SYLVANIA	VC3145	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
SYLVANIA	VC3145	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
SYLVANIA	VC3145	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
SYLVANIA	VC3145	N/A	DEW INDICATOR ILLUMINATES AND UNIT SHUTS DOWN	LOOSE CONNECTIONS ONTHE P3 PLUG
SYLVANIA	VC3145	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
SYLVANIA	VC3145	N/A	NO FIP LOADING MOTOR ENGAGES OK	CHECK/REPLACE C1020 C1021 L1005
SYLVANIA	VC3145	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
SYLVANIA	VC3145	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
SYLVANIA	VC3145	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
SYLVANIA	VC3145	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
SYLVANIA	VC3145	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
SYLVANIA	VC3145	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC3145	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
SYLVANIA	VC3145	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
SYLVANIA	VC3145	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
SYLVANIA	VC3145	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
SYLVANIA	VC3145	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
SYLVANIA	VC3145	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
SYLVANIA	VC3145	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
SYLVANIA	VC3145	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
SYLVANIA	VC3145	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
SYLVANIA	VC3145	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
SYLVANIA	VC3145	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
SYLVANIA	VC3145	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
SYLVANIA	VC3145	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
SYLVANIA	VC4010	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4010	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4010	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4010	N/A	MULTIPLE SOLENOID FAILURES	REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044
SYLVANIA	VC4020	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4020	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4020	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4020	N/A	MULTIPLE SOLENOID FAILURES	REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044
SYLVANIA	VC4024	N/A	MULTIPLE SOLENOID FAILURES	REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044
SYLVANIA	VC4024	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4024	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4024	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4040	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4040	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4040	N/A	MULTIPLE SOLENOID FAILURES	REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044
SYLVANIA	VC4040	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4044	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4044	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4044	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4044	N/A	MULTIPLE SOLENOID FAILURES	REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044
SYLVANIA	VC4070	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4070	N/A	MULTIPLE SOLENOID FAILURES	REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044
SYLVANIA	VC4070	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4070	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4115	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
SYLVANIA	VC4115	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4115	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
SYLVANIA	VC4115	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4115	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4120	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4120	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4120	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
SYLVANIA	VC4120	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4120	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
SYLVANIA	VC4120	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
SYLVANIA	VC4142	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
SYLVANIA	VC4142	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4142	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4142	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
SYLVANIA	VC4142	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4142	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
SYLVANIA	VC4143	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
SYLVANIA	VC4143	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
SYLVANIA	VC4143	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
SYLVANIA	VC4143	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4143	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4143	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4144	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
SYLVANIA	VC4144	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4144	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4144	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
SYLVANIA	VC4144	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
SYLVANIA	VC4144	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4145	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
SYLVANIA	VC4145	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4145	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4145	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4150	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
SYLVANIA	VC4150	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
SYLVANIA	VC4150	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
SYLVANIA	VC4150	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
SYLVANIA	VC4150	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
SYLVANIA	VC4150	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
SYLVANIA	VC4213	N/A	NO REWIND FUNCTION	CHECK/REPLACE RUBBER BUMPER ON DECK ASSY. (ITEM 41 ON DECK 3 EXPLODED VIEW) P/N# 483546667013
SYLVANIA	VC4223	N/A	NO REWIND FUNCTION	CHECK/REPLACE RUBBER BUMPER ON DECK ASSY. (ITEM 41 ON DECK 3 EXPLODED VIEW) P/N# 483546667013
SYLVANIA	VC4243	N/A	ONLY A BLUE SCREEN IS RECORDED ON A TIMED RECORDING OF A HRC CABLE SIGNAL	CHANGE C667 TO A 2.2uF @ 50V
SYLVANIA	VC4510	N/A	WARBLE IN AUDIO DURING PLAYBACK OF LINEAR AUDIO - CAN BE INTERMITTENT - MOST NOTICED ON STEADY TONES	CHECK/REPLACE CAPSTAN MOTOR ASSY.
SYLVANIA	VC4510	N/A	1 KHz AUDIO SQUEAL IN PLAYBACK AUDIO OF A RECORDING	INSTALL SHIELDING KIT (P/N# 483531057353)
SYLVANIA	VC4510	N/A	WITH AUTOMATIC DAYLIGHT SAVINGS FEATURE TURNED ON, CLOCK WILL LOSE AN HOUR EVERY SUNDAY DURING THE MONTH OF OCTOBER	CHECK/REPLACE IC6001 WITH NEW TYPE (P/N# 483520917458)
SYLVANIA	VC4510	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R10 (82 1watt), D06 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYLVANIA	VC4540	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R10 (82 1watt), D06 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYLVANIA	VC4540	N/A	1 KHz AUDIO SQUEAL IN PLAYBACK AUDIO OF A RECORDING	INSTALL SHIELDING KIT (P/N# 483531057353)
SYLVANIA	VC4540	N/A	WARBLE IN AUDIO DURING PLAYBACK OF LINEAR AUDIO - CAN BE INTERMITTENT - MOST NOTICED ON STEADY TONES	CHECK/REPLACE CAPSTAN MOTOR ASSY.
SYLVANIA	VC4560	N/A	TIMER WILL NOT PERFORM A NEXT DAY UP TO A 1 YEAR PROGRAMMED RECORDING DURING THE MONTHS OF OCT.,NOV., AND DEC.	CHECK/REPLACE IC6K WITH NEW TYPE (P/N# 483520917471)
SYLVANIA	VC8940	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
SYLVANIA	VC8946	N/A	AFTER UNIT RUNS FOR 1/2 TO 1 HOUR, DISPLAY GOES OUT AND VCR LOCKS UP - WON'T TAKE ANY COMMANDS	CHECK/REPLACE IC7502 (MN1280-R) RESET IC
SYLVANIA	VC8952	N/A	AFTER UNIT RUNS FOR 1/2 TO 1 HOUR, DISPLAY GOES OUT AND VCR LOCKS UP - WON'T TAKE ANY COMMANDS	CHECK/REPLACE IC7502 (MN1280-R) RESET IC
SYLVANIA	VC8954	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
SYLVANIA	VC8954	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
SYLVANIA	VC8954	N/A	DD CYL. MOTOR ROTATES VERY SLOW/ROTATE BACK FORT	CHECK OR REPLACE THE DD CYL.
SYLVANIA	VC8954	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC8954	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
SYLVANIA	VC8954	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
SYLVANIA	VC8954	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
SYLVANIA	VC8954	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
SYLVANIA	VC8954	N/A	NO DRUM LOCK - PIX HAS HORZ. LINES	CHECK/REPLACE C2010 AND C2011 FOR LEAKAGE OR A CHANGE IN VALUE.
SYLVANIA	VC8954	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
SYLVANIA	VC8954	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
SYLVANIA	VC8954	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
SYLVANIA	VC8954	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
SYLVANIA	VC8954	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
SYLVANIA	VC8954	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
SYLVANIA	VC8954	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
SYLVANIA	VC8954	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
SYLVANIA	VC8954	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
SYLVANIA	VC8954	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
SYLVANIA	VC8954	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
SYLVANIA	VC8954	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
SYLVANIA	VC8954	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
SYLVANIA	VC8954	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
SYLVANIA	VC8954	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
SYLVANIA	VC8954	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC8960	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
SYLVANIA	VC8960	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC8960	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
SYLVANIA	VC8960	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
SYLVANIA	VC8960	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
SYLVANIA	VC8960	N/A	TUNER VIDEO PRESENT WHILE PLAYING TAPE	REPLACE IC3101
SYLVANIA	VC8960	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
SYLVANIA	VC8960	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
SYLVANIA	VC8960	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
SYLVANIA	VC8960	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
SYLVANIA	VC8960	N/A	TUNES CHANNELS MANUALLY BUT WON'T HOLD CHANNEL MEMORY	CHECK/REPLACE IC7603
SYLVANIA	VC8960	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
SYLVANIA	VC8960	N/A	SNOWY PIX-TUNING DRIFTS-MAY IMPROVE AFTER WARM	CHECK IC701
SYLVANIA	VC8960	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
SYLVANIA	VC8960	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
SYLVANIA	VC8960	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
SYLVANIA	VC8960	N/A	WILL NOT LOAD CARRIAGE MOTOR OR TAPE TRANSPORT MOTOR - POWER SHUTS OFF AFTER 5 SECONDS	CHECK/REPLACE Q1203 FOR SHORT
SYLVANIA	VC8960	N/A	NO VV OR EE VIDEO AUDIO OK BOTH MODES	CHECK FOR OPEN L3101 COIL
SYLVANIA	VC8960	N/A	NO VIDEO IN VCR MODE AUDIO OK LOSS OF VIDEO Bt.	CHECK AND OR REPLACE L3101
SYLVANIA	VC8960	N/A	CASSETTE LOADS OK DD CYLINDER STARTS	REPLACE IC2001
SYLVANIA	VC8960	N/A	INT. GOOD PIX. / SNOW IN PLAYBACK	CHECK IC2003
SYLVANIA	VC8960	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
SYLVANIA	VC8960	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
SYLVANIA	VC8960	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
SYLVANIA	VC8960	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
SYLVANIA	VC8960	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER AND CLUTCH ASSY OR IDLER
SYLVANIA	VC8960	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
SYLVANIA	VC8960	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
SYLVANIA	VC8960	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
SYLVANIA	VC8960	N/A	NO VIDEO IN TUNER MODE WITH RF INPUT AUDIO OK	CHECK D4401 OR D4052
SYLVANIA	VC8960	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
SYLVANIA	VC8960	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
SYLVANIA	VC8960	N/A	WARBLE IN AUDIO ESPECIALLY ON LP AND SLP	CHECK/REPLACE C1018 AND C1019
SYLVANIA	VC8960	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
SYLVANIA	VC8960	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
SYMPHONIC	5300	N/A	INT COLOR AFTER 2-3 HRS. OF PLAY OR RECORD	CHECK/REPLACE HIC101
SYMPHONIC	6460	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	6470	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	6480	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R10 (82 1watt), D06 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	7400A	N/A	BLUE SCREEN ON P.B.- AUDIO NORMAL	DIRTY HEADS OR TRACKING (VIDEO MUTE CONDITION)
SYMPHONIC	7400A	N/A	PLAY AUDIO GOOD-RECORD AUDIO VERY WEAK	DEFECTIVE AUDIO/CTRL HEAD
SYMPHONIC	7400A	N/A	NO SPEED SELECT ON ON PLAYBACK OR RECORD	REPLACE DEFECTIVE IC (BA718) ECG1529
SYMPHONIC	7560	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	7580	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R10 (82 1watt), D06 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	FV2000	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	FV2500	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	SC670	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	SC970	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	SE226	N/A	SAME AS A MAGNAVOX VRU422
SYMPHONIC	SE226D	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE R8,R9,R10 (27?483511057174), D08 ECG519 OR	483513037048),IC01(483513087078),R13/R14(1.5?483511057074) D16 (483513037135), Q01 (483513047139), Q02 (483513047879)
SYMPHONIC	SE226G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SE426G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SE426J	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SE436G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SE436J	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SV206G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SV211E	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE R7,R8,R9 (27?483511057174), D9 ECG519 OR	483513037048), IC01(483513087078), R12(0.82?@ 1w) D15 (483513037135), Q01 (483513047139), Q02 (483513047879)
SYMPHONIC	SV2161D	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE R8,R9,R10 (27?483511057174), D08 ECG519 OR	483513037048),IC01(483513087078),R13/R14(1.5?483511057074) D16 (483513037135), Q01 (483513047139), Q02 (483513047879)
SYMPHONIC	SV2161G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SV221E	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE R7,R8,R9 (27?483511057174), D9 ECG519 OR	483513037048), IC01(483513087078), R12(0.82?@ 1w) D15 (483513037135), Q01 (483513047139), Q02 (483513047879)
SYMPHONIC	SV421E	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE R7,R8,R9 (27?483511057174), D9 ECG519 OR	483513037048), IC01(483513087078), R12(0.82?@ 1w) D15 (483513037135), Q01 (483513047139), Q02 (483513047879)
SYMPHONIC	SV4261G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SV427SG	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SV4361G	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SV447SG	N/A	DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048)	IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879)
SYMPHONIC	SVX1000	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
SYMPHONIC	SVX1200	N/A	DEAD SET	CHECK/REPLACE Q01 (2SC4204),Q02 (2SC4418),R13 (82 1watt), D03 (1N4148), R14 (0.68 1watt), R02 (4.7 2watt)
TATUNG	VRH8300U	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
TATUNG	VRH8300U	N/A	PLAYS IN SP SPEED ONLY	CHECK AND OR REPLACE IC 207
TATUNG	VRH8300U	N/A	SHUTS DOWN FROM PLAY MODE AFTER 10 TO 60 MINUTES	CHECK/REPLACE THE REEL SENSOR
TATUNG	VRH8300U	N/A	AUDIO NORMAL ON TUNER BUT NO VIDEO	CHECK FOR DIRTY CONTACTS ON 'TV-AUX' SWITCH
TATUNG	VRH8300U	N/A	NO CAPSTAN DRIVE IN ANY MODE	CHECK FOR BROKEN SOLDER JOINTS ON Q202 (FOIL SIDE)
TATUNG	VRH8300U	N/A	DEAD	CHECK/REPLACE OPEN CP1 OR CP2 ON POWER SUPPLY
TATUNG	VRH8300U	N/A	NO CAPSTAN OPERATION IN PLAY MODE (INTERMITTENT)	CHECK CONNECTIONS ON CN3
TEKNIKA	VCR905	N/A	WILL NOT ACCEPT TAPE	CHECK IC602
TEKNIKA	VCR905	N/A	1 KHz TONE IN AUDIO ON PLAYBACK	CHECK/REPLACE R401 OR OPEN GROUND TO THE GROUND SIDE OF
TEKNIKA	VCR905	N/A	NO SPEED CONTROL - RUNAWAY ON PLAY	CHECK/REPLACE C247 AND C248
TEKNIKA	VCR985	N/A	WASHED OUT VIDEO-LOW LUMINANCE LEVEL	CHECK IC302 (GOLDSTAR 669-051A)
TEKNIKA	VCR985	N/A	WILL NOT RECORD A CONTROL TRACK ON TAPE - PRE-RECORDED TAPES WOULD PLAYBACK FINE ON ALL SPEEDS	CHECK/REPLACE IC201 (P/N# 668-156A)
TEKNIKA	VCR985	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
TMK	2053	N/A	EATING TAPES	REPLACE IDLER WHEEL
TMK	3033	N/A	]SLOW ON REWIND,FAST FORWARD,EATING TAPES	CHECK IDLER ASSEMBLY
TMK	VCR2030	N/A	NO CLOCK DISPLAY	CHECK R501 (68 OHM) FOR OPEN
TOSHIBA	DX3	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	DX3	N/A	ABNORMAL PIX IN E-E & PLAY MODES,NO COLOR,VIDEO	CHECK PIN#1 OF Z201 FOR PROPER WAVE. REPL. IF MISSING
TOSHIBA	DX7	N/A	(INDEXING) ERRORS FINDING THE BEGINNING OF REC.	ADD .1uF BETWEEN PIN 1 & 2 OF P704
TOSHIBA	DX7	N/A	LOW TORQUE IN PLAY AND RECORD	REMOVE JUMPER JP623,INST. JUMPER Q627(E) TO Q620(E)
TOSHIBA	DX7	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	DX7	N/A	COLORED VERTICAL NOISE BARS IN PLAY MODE-DARK PX	REPLACE THE 1H DELAY LINE X401 (70138064)
TOSHIBA	M120	N/A	NO FF/REW AND TAPE JAMS IN REC/PLAYBACK	THIS IS CAUSED BY LOW REEL TORQUE--
TOSHIBA	M120	N/A	WILL NOT AUTO-REWIND - WILL SOMETIMES BREAK THE TAPE	CHECK/REPLACE C806 IN POWER SUPPLY
TOSHIBA	M1283	N/A	WILL NOT ERASE OLD AUDIO	CHECK/REPLACE IC701 AND Q702
TOSHIBA	M1287	N/A	WILL NOT ERASE OLD AUDIO	CHECK/REPLACE IC701 AND Q702
TOSHIBA	M210	N/A	DEAD - NO FUNCTIONS WORK	CHECK/REPLACE R803
TOSHIBA	M210	N/A	NO FF/REW AND TAPE JAMS IN REC/PLAYBACK	THIS IS CAUSED BY LOW REEL TORQUE--
TOSHIBA	M2100	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2100	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2100	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2100	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2100	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M2100	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2100	N/A	POOR OR NO AUDIO IN RECORD OR IN E-E	REPLACE 4.5MHZ FILTER (Z003)-CHECK C016 FOR BREAKS
TOSHIBA	M2110	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2120	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2120	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2120	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M2120	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2120	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2120	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2130	N/A	FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT.	IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA	M2130	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2130	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2130	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2130	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2130	N/A	PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF	REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA	M2130	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M2130	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M220	N/A	DEAD - NO FUNCTIONS WORK	CHECK/REPLACE R803
TOSHIBA	M220	N/A	NO FF/REW AND TAPE JAMS IN REC/PLAYBACK	THIS IS CAUSED BY LOW REEL TORQUE--
TOSHIBA	M2200	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M2200	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2200	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2200	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2200	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2200	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M221	N/A	CAPSTAN MOTOR WON'T RUN IN PLAY OR RECORD - WORKS FINE IN REWIND AND FAST FORWARD	CHECK/REPLACE D108,D109 AND D110
TOSHIBA	M221	N/A	MISSING 'AL' 6 VOLT SUPPLY	CHECK/REPLACE D1103 AND D1104 (MAY CHECK GOOD)
TOSHIBA	M222	N/A	NO POWER (DEAD)	CHECK/REPLACE D105,D106,D108,D109,D110,D1103,D1104,D112, D113 FOR OPEN
TOSHIBA	M222	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
TOSHIBA	M222	N/A	CAPSTAN MOTOR WILL NOT RUN	CHECK/REPLACE D105,D106,D108,D109,D110,D1103,D1104,D112, D113 FOR OPEN
TOSHIBA	M222	N/A	CYLINDER MOTOR WILL NOT RUN	CHECK/REPLACE D105,D106,D108,D109,D110,D1103,D1104,D112, D113 FOR OPEN
TOSHIBA	M222	N/A	CAPSTAN MOTOR WON'T RUN IN PLAY OR RECORD - WORKS FINE IN REWIND AND FAST FORWARD	CHECK/REPLACE D108,D109 AND D110
TOSHIBA	M2220	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M2220	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2220	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2220	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2220	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2230	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M225	N/A	DEAD - NO FUNCTIONS WORK	CHECK/REPLACE R803
TOSHIBA	M226	N/A	MISSING 'AL' 6 VOLT SUPPLY	CHECK/REPLACE D1103 AND D1104 (MAY CHECK GOOD)
TOSHIBA	M226	N/A	CAPSTAN MOTOR WON'T RUN IN PLAY OR RECORD - WORKS FINE IN REWIND AND FAST FORWARD	CHECK/REPLACE D108,D109 AND D110
TOSHIBA	M227	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
TOSHIBA	M227	N/A	CAPSTAN MOTOR WON'T RUN IN PLAY OR RECORD - WORKS FINE IN REWIND AND FAST FORWARD	CHECK/REPLACE D108,D109 AND D110
TOSHIBA	M228	N/A	VCR GOES INTO PLAY MODE - ALL FUNCTIONS LOOK NORMAL BUT NO PICTURE	CHECK/REPLACE Z681 (ICP) FOR OPEN
TOSHIBA	M228	N/A	CASSETTE WILL NOT LOAD OR CASSETTE LOADS BUT THEN IS EJECTED OR CASSETTE WILL NOT EJECT	REPLACE RIGHT SIDE PLATE (P/N # 70790457) , SHAFT ARM ASSY. (P/N # 70790005) AND EJECT GEAR (P/N # 70790393)
TOSHIBA	M228	N/A	NO POWER - FUSE F1 BLOWN	INSTALL PARTS IN THE FOLLOWING KIT (P/N# 70796058)
TOSHIBA	M2283	N/A	WILL NOT ERASE OLD AUDIO	CHECK/REPLACE IC701 AND Q702
TOSHIBA	M2300	N/A	POOR OR NO AUDIO IN RECORD OR IN E-E	REPLACE 4.5MHZ FILTER (Z003)-CHECK C016 FOR BREAKS
TOSHIBA	M2300	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2300	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2320	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2330	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2330	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2330	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M2330	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2330	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2330	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M240	N/A	NO FF/REW AND TAPE JAMS IN REC/PLAYBACK	THIS IS CAUSED BY LOW REEL TORQUE--
TOSHIBA	M240	N/A	DEAD - NO FUNCTIONS WORK	CHECK/REPLACE R803
TOSHIBA	M2420	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2420	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2420	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2420	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2420	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M2430	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M2430	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M2430	N/A	FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT.	IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA	M2430	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M2430	N/A	PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF	REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA	M2430	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M2430	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M249	N/A	CASSETTE WILL NOT LOAD OR CASSETTE LOADS BUT THEN IS EJECTED OR CASSETTE WILL NOT EJECT	REPLACE RIGHT SIDE PLATE (P/N # 70790457) , SHAFT ARM ASSY. (P/N # 70790005) AND EJECT GEAR (P/N # 70790393)
TOSHIBA	M250	N/A	DEAD - NO POWER	CHECK/REPLACE PW801 (P/N3 BZ680032)
TOSHIBA	M260	N/A	DEAD - NO POWER	CHECK/REPLACE PW801 (P/N3 BZ680032)
TOSHIBA	M261	N/A	UNIT TRIES TO LOAD A CASSETTE WITHOUT ONE IN IT - TURNS OFF AFTER A FEW SECONDS	CHECK/RESOLDER CONNECTIONS ON S601 AND S602
TOSHIBA	M262	N/A	AUDIO IN THE E/E MODE IS LOWER THAN WHEN VCR IS TURNED OFF	ADD A 220?1/8w RESISTOR (P/N# 24376221) IN PARALLEL WITH RA01
TOSHIBA	M2700	N/A	POOR OR NO AUDIO IN RECORD OR IN E-E	REPLACE 4.5MHZ FILTER (Z003)-CHECK C016 FOR BREAKS
TOSHIBA	M2700	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M3400	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4100	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M4100	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M4100	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4100	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M4100	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M4100	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M4120	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4130	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4130	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M4130	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M4130	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M4130	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M4130	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M4200	N/A	NO REWIND/FAST FORWARD OR LOW TORQUE	IC507,IC603,IC601
TOSHIBA	M4200	N/A	PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF	REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA	M4200	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M4200	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)
TOSHIBA	M4200	N/A	HORZ. BAR THUR PIX ABOUT 2' WIDE	IC501
TOSHIBA	M4200	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4200	N/A	INT. SPEED SELECT	IC501
TOSHIBA	M4200	N/A	FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT.	IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA	M4220	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4230	N/A	PLAYBACK,CUE,REVIEW MAY CAUSE UNIT TO SHUT OFF	REPLACE THE CAM SWITCH (70197081) (SJ00251)
TOSHIBA	M4230	N/A	FF/REW NO TAPE COUNTER--PLAY/REC. NO TAPE COUNT.	IC604 DAMAGED BY STATIC--INST.SCREW IN REEL MOTOR!!!
TOSHIBA	M4230	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4230	N/A	LOW AUDIO ON RECORD - PLAYBACK OF PRE-RECORDED TAPE WAS NORMAL.	CHECK/REPLACE AUDIO/CTRL HEAD (70182055)
TOSHIBA	M4230	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M4300	N/A	POOR OR NO AUDIO IN RECORD OR IN E-E	REPLACE 4.5MHZ FILTER (Z003)-CHECK C016 FOR BREAKS
TOSHIBA	M4300	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4300	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M4320	N/A	WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY	ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND
TOSHIBA	M4330	N/A	WILL NOT LOAD TAPE--INTERMITTENT	CHECK BOTH LOADING SWITCHES ON CARRIAGE FOR HIGH
TOSHIBA	M4330	N/A	PRESS PLAY AND IT LOOKS LIKE ITS IN FAST FORWARD	REPLACE CAM SWITCH (SJ00251)

LAMSON Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675  TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:lamsonsm@gmail.com    YAHOO MESSENGER ID : myrna_q_ng or saishu_ng SKYPE ID: myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be using the old address and phone no. in the future. Please be noted when calling us, sending letters, parcels or buying our products> OLD Address: 681 Carmen Building, Ronquillo St. Quiapo, Manila, Philippines Phone:00632-7332936 7332940 Fax:00632-7332940 E-mail: