| MAKE | MODEL | CHASSIS | SYMPTOM | CURE | |
| FISHER | PC6225 | N/A | No Tuner Action | R106-39K open location front right side near power | |
| FISHER | PT800 | N/A | POP IN AUDIO WHEN SET IS TURNED OFF | CHECK/REPLACE C1845 | |
| FUNAI | FT1341 | N/A | DEAD - RELAY CLICKS ON THEN BACK OFF | CHECK/REPLACE R653 (1?@ 1/2w.) | |
| FUNAI | FT1941 | N/A | SET THUMPS WHEN TURNED OFF BUT WORKS NORMALLY OTHERWISE | CHECK/REPLACE D602 (P/N# ECG125) | |
| FUNAI | FTV13TD | N/A | DEAD - RELAY CLICKS ON THEN BACK OFF | CHECK/REPLACE R653 (1?@ 1/2w.) | |
| FUNAI | FTV13TE | N/A | DEAD - RELAY CLICKS ON THEN BACK OFF | CHECK/REPLACE R653 (1?@ 1/2w.) | |
| FUNAI | T20M | L5100U2 | DEAD - STANDBY POWER LIGHT LIT AND RELAY CLICKS | CHECK/REPLACE C16 IN POWER SUPPLY (NEAR FRONT RIGHT CORNER) | |
| GE | N/A | 10AB | INTM. COLOR,POWER,VERT,HORZ | CHECK/RESOLDER CONNECTIONS ON ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 10AB | DEAD SET | CHECK/RESOLDER CONNECTIONS ON ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 10AB | NO VERT.SWEEP | CHECK/REPLACE R611 (330k) ALSO ALL GRIPLET CONNECTIONS ON THE MAIN BOARD. | |
| GE | N/A | 10AB | RETRACE LINES IN PIX | CHECK/REPLACE 4.7 OHM RESISTOR NEAR YOKE PLUG | |
| GE | N/A | 10AC | NO VERT.SWEEP | CHECK/REPLACE R611 (330k) ALSO ALL GRIPLET CONNECTIONS ON THE MAIN BOARD. | |
| GE | N/A | 10AC | RETRACE LINES IN PIX | CHECK/REPLACE 4.7 OHM RESISTOR NEAR YOKE PLUG | |
| GE | N/A | 10AC | INTM. COLOR,POWER,VERT,HORZ | CHECK/RESOLDER CONNECTIONS ON ALL GRIPLETS | |
| GE | N/A | 10AC | DEAD SET | CHECK/RESOLDER CONNECTIONS ON ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 13AB | RETRACE LINES IN PIX | CHECK/REPLACE 4.7 OHM RESISTOR NEAR YOKE PLUG | |
| GE | N/A | 13AB | DEAD SET | RESOLDER ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 13AB | INTERMITTENT COLOR,POWER,VERT,HORZ | CHECK/RESOLDER CONNECTIONS ON GRIPLETS | |
| GE | N/A | 13AB | NO VERT.SWEEP | CHECK/REPLACE R611 (330k) ALSO ALL GRIPLET CONNECTIONS ON THE MAIN BOARD. | |
| GE | N/A | 13AC | RETRACE LINES IN PIX | CHECK/REPLACE 4.7 OHM RESISTOR NEAR YOKE PLUG | |
| GE | N/A | 13AC | INTM. COLOR,POWER,VERT,HORZ | RESOLDER ALL GRIPLET CONNECTIONS | |
| GE | N/A | 13AC | NO VERT.SWEEP | CHECK/REPLACE R611 (330k) ALSO ALL GRIPLET CONNECTIONS ON THE MAIN BOARD. | |
| GE | N/A | 13AC | DEAD SET | RESOLDER ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 13PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | N/A | 17AB | RETRACE LINES IN PIX | 4.7 OHM RESISTOR NEAR YOKE PLUG | |
| GE | N/A | 17AB | DEAD SET | RESOLDER ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 17AB | INTM. COLOR,POWER,VERT,HORZ | RESOLDER ALL GRIPLET CONNECTIONS | |
| GE | N/A | 17AB | NO VERT.SWEEP | CHECK/REPLACE R611 (330k) ALSO ALL GRIPLET CONNECTIONS ON THE MAIN BOARD. | |
| GE | N/A | 17AC | DEAD SET | RESOLDER ALL GRIPLETS ON MAIN BOARD | |
| GE | N/A | 17AC | NO VERT.SWEEP | CHECK/REPLACE R611 (330k) ALSO ALL GRIPLET CONNECTIONS ON THE MAIN BOARD. | |
| GE | N/A | 17AC | INTM. COLOR,POWER,VERT,HORZ | RESOLDER ALL GRIPLET CONNECTIONS | |
| GE | N/A | 17AC | RETRACE LINES IN PIX | 4.7 OHM RESISTOR NEAR YOKE PLUG | |
| GE | N/A | 19EC | INSUFFICIENT HEIGHT OF PIX | CHECK R606 | |
| GE | N/A | 19EC | NO RASTER BUT HAS SOUND AND HV | CHECK JOINTS AT 37A AND 37B (GRIPLETS) | |
| GE | N/A | 19EC | INTERMITTENT COLOR SATURATION | CHECK C366 | |
| GE | N/A | 19EC | NO RASTER BUT HAS SOUND AND HIGH VOLTAGE | CHECK Q212 | |
| GE | N/A | 19EC | INTERMITTENT SOUND W/ LOSS OF 15V SUPPLY | CHECK GRIPLET AT Q905(E) AND RL-35 #6 ON EP93X295 BD. | |
| GE | N/A | 19EC | ERRATIC HORZ. DRIVE | CHECK C523 | |
| GE | N/A | 19PM | F903 OPEN AND Q901 SHORTED | CHECK/REPLACE R916 (110k),Q901,Y913,Y914 AND F903 | |
| GE | N/A | 19PM | NUISANCE SHUTDOWN | ADD A 1.5k IN SERIES WITH A 5.6v ZENER - INSTALL ACROSS R222 WITH ANODE OF ZENER AT JUNCTION OF R221 AND R222 | |
| GE | N/A | 25PC | VERTICAL JITTER WITH A VCR | JUMPER R602 (SHORT IT) | |
| GE | N/A | 25PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C614 | |
| GE | N/A | 25PC | WEAK HORZ. SYNC - SET MAY LOOSE COLOR SYNC | CHANGE R516 TO 150k (CAN BE AS LOW AS 75k) | |
| GE | N/A | 25PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | N/A | 25PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | N/A | 25PC | SHORT VERT SWEEP | CHECK C621 FOR OPEN OR VALUE CHANGE | |
| GE | N/A | 25PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C619 | |
| GE | N/A | 25PM | NUISANCE SHUTDOWN | ADD A 1.5k IN SERIES WITH A 5.6v ZENER - INSTALL ACROSS R222 WITH ANODE OF ZENER AT JUNCTION OF R221 AND R222 | |
| GE | N/A | 25PM | F903 OPEN AND Q901 SHORTED | CHECK/REPLACE R916 (110k),Q901,Y913,Y914 AND F903 | |
| GE | N/A | 26PM | NUISANCE SHUTDOWN | ADD A 1.5k IN SERIES WITH A 5.6v ZENER - INSTALL ACROSS R222 WITH ANODE OF ZENER AT JUNCTION OF R221 AND R222 | |
| GE | N/A | 26PM | F903 OPEN AND Q901 SHORTED | CHECK/REPLACE R916 (110k),Q901,Y913,Y914 AND F903 | |
| GE | 13GP203 | TX81 | DEAD SET | CHECK/REPLACE DP12 FOR SHORT | |
| GE | 13GP203 | TX81 | DEAD SET WITH TIC-TIC | CHECK/REPLACE TP11 FOR SHORT | |
| GE | 13GP203 | TX81 | NO BRIGHTNESS | CHECK/REPLACE CV14 FOR SHORT | |
| GE | 13GP203 | TX81 | DEAD SET | CHECK/REPLACE FP01,TP10 AND SHORTED LP04 | |
| GE | 13GP234 | TX81 | HIGHLY INTERMITTENT SHUTDOWN WITH MOTORBOAT IN AUDIO | CHECK/REPLACE INTERMITTENT DP01 | |
| GE | 13GP234 | TX81 | DEAD WITH LINE FUSE OPEN,TP10 SHORTED AND CP22 BULGED - 150 VOLT LINE UP TO 350 VOLTS | CHECK/RESOLDER CONNECTIONS ON CP17 | |
| GE | 13GP234 | TX81 | DEAD SET WITH OPEN FUSE | CHECK/REPLACE FP01,TP10 AND CP08 | |
| GE | 13GP235 | TX82 | WON'T TNER CHANNEL 3, 16, 17 O CABLE - ALL OTHER CHANNELS TUNE OK | CHECK/REPLACE CP47 | |
| GE | 13GP235 | TX82 | DEAD SET | CHECK/REPLACE CP15,FP01,TP05,TP06,TP10,DP32,RP50 | |
| GE | 13GP235C01 | TX82T | DEAD SET WITH TIC-TIC | CHECK/REPLACE TP11 FOR SHORT | |
| GE | 13GP235C01 | TX82T | DEAD SET | CHECK/REPLACE DP12 FOR SHORT | |
| GE | 13GP237 | TX82 | DEAD SET - PULSES | CHECK/REPLACE DP18 LEAKY (MAY CHECK OK OUT OF CIRCUIT) | |
| GE | 13GP237 | TX82 | DEAD SET | CHECK/REPLACE CR14 | |
| GE | 13GP237 | TX82 | DEAD SET | CHECK/REPLACE CP15,FP01,TP05,TP06,TP10,DP32,RP50 | |
| GE | 13GP237 | TX82 | NO PICTURE - SOUND OK - MISSING CRT FILAMENTS | CHECK/REPLACE RP50 | |
| GE | 13GP237 | TX82 | DEAD SET | CHECK/REPLACE CP01 (100uF @ 35v) | |
| GE | 13GP239 | TX826 | DEAD SET | CHECK/REPLACE DP06 (4.7v ZENER - ECG5009A) | |
| GE | 13GP300 | CN150 | CLOCK RESETS WHEN SLEEP TIMER IS USED | INSTALL KIT (P/N# 212122) | |
| GE | 13GP300 | CN150 | DEAD SET - NO 5 VOLTS OR LOW 5 VOLTS ON PIN #20 OF MICROPROCESSOR IC | CHECK/REPLACE D710 (ECG125) (P/N# 210227) | |
| GE | 13GP301 | CN150 | CLOCK RESETS WHEN SLEEP TIMER IS USED | INSTALL KIT (P/N# 212122) | |
| GE | 13GP410 | CTC135 | INTERMITTENT START-UP | CHECK/REPLACE CR931 (27v ZENER) | |
| GE | 13GP410 | CTC135 | DEAD SET AND MAKES A TIC-TIC SOUND | CHECK/REPLACE R112 | |
| GE | 13GP430 | CTC145 | LOW AUDIO DISTORTION | CHECK/REPLACE Q1201 | |
| GE | 13GP430 | CTC145 | LOW BRIGHTNESS - RAISING G2 CAUSES RETRACE LINES | CHECK/REPLACE R2715 | |
| GE | 13GP430 | CTC145 | NO VIDEO OR OSD | CHECK/REPLACE Q2706 | |
| GE | 13GP430 | CTC145 | TV CYCLES ON/OFF WHEN POWER BUTTON PRESSED | CHECK/REPLACE C3126 FOR LEAKAGE | |
| GE | 13PF6500 | NF | SHORT VERT SWEEP AND PIX ROLLS | CHECK/REPLACE R443 FOR INCREASE IN VALUE | |
| GE | 17AC2642W | 17AC | BRIGHT SCREEN WITH RETRACE LINES - SCREEN CTRLS. WILL NOT CORRECT HIGH BRIGHTNESS. | CHECK R756 AND R757 FOR OPEN | |
| GE | 19GT300 | CN150 | CLOCK RESETS WHEN SLEEP TIMER IS USED | INSTALL KIT (P/N# 212122) | |
| GE | 19GT300 | CN150 | DEAD SET - NO 5 VOLTS OR LOW 5 VOLTS ON PIN #20 OF MICROPROCESSOR IC | CHECK/REPLACE D710 (ECG125) (P/N# 210227) | |
| GE | 19PC3704W | 19PC | WEAK HORZ. SYNC - SET MAY LOOSE COLOR SYNC | CHANGE R516 TO 150k (CAN BE AS LOW AS 75k) | |
| GE | 19PC3704W | 19PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C619 | |
| GE | 19PC3704W | 19PC | VERTICAL JITTER WITH A VCR | JUMPER R602 (SHORT IT) | |
| GE | 19PC3704W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC3704W | 19PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C614 | |
| GE | 19PC3704W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC3704W | 19PC | SHORT VERT SWEEP | CHECK C621 FOR OPEN OR VALUE CHANGE | |
| GE | 19PC3704W | 19PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | 19PC3734W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC3734W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC3734W | 19PC | WEAK HORZ. SYNC - SET MAY LOOSE COLOR SYNC | CHANGE R516 TO 150k (CAN BE AS LOW AS 75k) | |
| GE | 19PC3734W | 19PC | SHORT VERT SWEEP | CHECK C621 FOR OPEN OR VALUE CHANGE | |
| GE | 19PC3734W | 19PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | 19PC3734W | 19PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C619 | |
| GE | 19PC3734W | 19PC | SHORT VERT SWEEP | CHECK C621 FOR OPEN OR VALUE CHANGE | |
| GE | 19PC3734W | 19PC | VERTICAL JITTER WITH A VCR | JUMPER R602 (SHORT IT) | |
| GE | 19PC3734W | 19PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | 19PC5730W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC5730W | 19PC | VERTICAL JITTER WITH A VCR | JUMPER R602 (SHORT IT) | |
| GE | 19PC5730W | 19PC | WEAK HORZ. SYNC - SET MAY LOOSE COLOR SYNC | CHANGE R516 TO 150k (CAN BE AS LOW AS 75k) | |
| GE | 19PC5730W | 19PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | 19PC5730W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC5730W | 19PC | NARROW HORZ. SWEEP AND SET BURNS UP R192 | CHECK/REPLACE C904,R192 (200 ohm) AND R1903 (HORIZONTAL CENTERING CONTROL) | |
| GE | 19PC5730W | 19PC | SHORT VERT SWEEP | CHECK C621 FOR OPEN OR VALUE CHANGE | |
| GE | 19PC5730W | 19PC | SHORT VERT SWEEP | CHECK C621 FOR OPEN OR VALUE CHANGE | |
| GE | 19PC5730W | 19PC | HORZ. CENTERING CONTROL SMOKES | CHECK/REPLACE C904 (100uF @ 160v) | |
| GE | 19PC5730W | 19PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C619 | |
| GE | 19PF3742 | 19PC | BRIGHT SCREEN WITH RETRACE LINES AND DOES HAVE WASHED OUT VIDEO | CHECK/REPLACE C939 FOR OPEN | |
| GE | 20GT309A03 | CTC146D | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT309A03 | CTC146D | IMMEDIATE SHUTDOWN | CHECK/REPLACE CR3104 | |
| GE | 20GT309A03 | CTC146D | FRONT BUTTONS BROKEN | CHECK/REPLACE BUTTON ASSY. (P/N# 206815) | |
| GE | 20GT309A03 | CTC146D | NO VIDEO - LOOKS LIKE A AGC PROBLEM | CHECK/REPLACE R2727 (3.9k) FOR OPEN | |
| GE | 20GT309A03 | CTC146D | NO SOUND BUT PICTURE AND COLOR OK | CHECK/REPLACE R1211,R1209,R1210,Q1203 AND Q1202 | |
| GE | 20GT311N02 | CTC146D | FRONT BUTTONS BROKEN | CHECK/REPLACE BUTTON ASSY. (P/N# 206815) | |
| GE | 20GT320TX2 | CTC175A2 | INTERMITTENT VERTICAL SWEEP OR SET TRIES TO COLLAPSE AT THE TOP | CHECK/RESOLDER CONNECTIONS ON U1001 PINS 15,16,17 AND 18 AND ALL PINS ON U4501 | |
| GE | 20GT320TX2 | CTC175A2 | CHROMA BAR AT THE TOP OF THE PICTURE DURING PLAYBACK OF A VIDEO TAPE | CHECK/REPLACE U1001 (P/N# 215524) | |
| GE | 20GT320TX2 | CTC175A2 | NO STEREO - OSD STEREO INDICATOR NEVER COMES ON | CHECK/REPLACE C1707 (P/N# 205230) | |
| GE | 20GT320TX2 | CTC175A2 | DEAD SET WITH NO SOUND OR PICTURE BUT HAS HIGH VOLTAGE | CHECK/REPLACE CR4704 (P/N# 207878),R4702 (3.3 P/N# 217315) AND R4517 (24 P/N# 217314) | |
| GE | 20GT320TX2 | CTC175A2 | TUNER LOCAL OSCILLATOR DROPS OUT ON BAND TWO | CHANGE C7311 TO NEW PART (P/N# 194906) - BANDS ONE AND TWO OF TUNER MUST BE REALIGNED | |
| GE | 20GT320TX2 | CTC175A2 | UNABLE TO TUNE ABOVE CHANNEL 4 OR INTERMITTENT SHUTDOWN | CHECK/RESOLDER CONNECTIONS ON ALL GROUND SHIELDS AROUND TUNER AND SYSCON IC | |
| GE | 20GT320TX2 | CTC175A2 | POOR REGULATION - B+ RUNNING ABOUT 120v | CHECK/REPLACE Q4153 FOR LEAKAGE - MAY CHECK FINE OUT OF CIRCUIT | |
| GE | 20GT360FB1 | CTC166A | WHEN POWER BUTTON IS PUSHED, SET PULSES ON AND OFF TWICE THEN REMAINS OFF | CHECK/REPLACE R4175 | |
| GE | 20GT360FB1 | CTC166A | VERY INTERMITTENT LOSS OF SYNC | CHECK/REPLACE U1001 | |
| GE | 20GT370NB1 | CTC166B | VERY INTERMITTENT LOSS OF SYNC | CHECK/REPLACE U1001 | |
| GE | 20GT370NB1 | CTC166B | WHITE RASTER WITH RETRACE - NO SOUND | CHECK/REPLACE CR4118 (ECG125) (MAY CHECK GOOD) | |
| GE | 20GT406 | CTC146H | NO VIDEO AND NO COLOR SYNC | CHECK/REPLACE R2728 FOR OPEN | |
| GE | 20GT406 | CTC146H | NO PICTURE - OSD AND AUDIO OK | CHECK/REPLACE R2602 | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | NO OSD | CHECK Q4501 FOR LEAKAGE | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | SET COMES ON AND SHUTS DOWN IMMEDIATELY | CHECK/RESOLDER CONNECTIONS ON T4401 | |
| GE | 20GT420 | CTC146 | NO PIX-SOUND OK-MISSING G1,G2 AND FOCUS VOLTAGES | CHECK/REPLACE FLYBACK TRANSFORMER | |
| GE | 20GT420 | CTC146 | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT420 | CTC146 | NO COLOR BUT ON-SCREEN COLOR INDICATOR DOES CHANGE | CHECK/REPLACE C2810,C2811 AND C2812 FOR LEAKY OR A CHANGE IN VALUE. | |
| GE | 20GT420 | CTC146 | HORIZONTAL RUNNING OFF FREQUENCY | CHECK/REPLACE C4405 FOR LEAKAGE | |
| GE | 20GT420 | CTC146 | POOR REGULATION ALSO NARROW WIDTH | CHECK/REPLACE Q4102 (P/N# 193057) AND R4106 (P/N# 193068) | |
| GE | 20GT420 | CTC146 | FRONT BUTTONS BROKEN | CHECK/REPLACE BUTTON ASSY. (P/N# 206815) | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | MAKES CLICKING SOUND - NO SOUND AND NO PICTURE | CHECK/REPLACE CR4118 | |
| GE | 20GT420 | CTC146 | IMMEDIATE SHUTDOWN | CHECK/REPLACE CR3104 | |
| GE | 20GT420 | CTC146 | TV CYCLES ON/OFF WHEN POWER BUTTON PRESSED | CHECK/REPLACE C3126 FOR LEAKAGE | |
| GE | 20GT420 | CTC146 | NO LUMINANCE OR DARK PICTURE | CHECK/REPLACE R2727,R2728 OR R2729 | |
| GE | 20GT420 | CTC146 | NO AUTO-PROGRAMMING - WILL NOT RECEIVE CHANNELS 7-13 BUT CAN MANUALLY SELECT CHANNELS 2-6 | CHECK/REPAIR OPEN TRACE BETWEEN R4128 AND JW26 | |
| GE | 20GT420 | CTC146 | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | NO AUTO-PROGRAMMING | CHECK/REPLACE L2312 FOR OPEN | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | DEAD - RELAY DOES CLICK | CHECK/RESOLDER CONNECTIONS ON T401 | |
| GE | 20GT420 | CTC146 | MAKES CLICKING SOUND - NO SOUND AND NO PICTURE | CHECK/REPLACE CR4118 | |
| GE | 20GT420 | CTC146 | HORIZONTAL OFF FREQUENCY - NO WAVEFORM PRESENT AT U1001 PIN #59 | CHECK/REPAIR OPEN TRACE AT PIN 2 OF FLYBACK | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | NO PIX BUT AUDIO IS NORMAL | CHECK/REPLACE DL2701 FOR SHORT TO GROUND | |
| GE | 20GT420 | CTC146 | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT420 | CTC146 | NO OSD (MISSING 7MHz OSC) | CHECK/REPLACE L3301,C3330,C3331 AND U3300 | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | MECHANICAL BUZZ INTERMITTENT | CHECK/REPLACE YOKE ASSEMBLY | |
| GE | 20GT420 | CTC146 | DEAD SET - TRIES TO START BUT ONLY TICKS | CHECK/REPLACE Q4402 AND R4101 | |
| GE | 20GT420 | CTC146 | NO PIX-SOUND OK-MISSING G1,G2 AND FOCUS VOLTAGES | CHECK/REPLACE FLYBACK TRANSFORMER | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | DEAD SET WITH NO CLICK OR ANYTHING - ALSO WEAK CLOCK PULSES ON PINS 38 & 39 OF IC U3100 | CHECK/REPLACE Y3301 (182839) FOR WEAK OUTPUT | |
| GE | 20GT420 | CTC146 | JAIL BARS OR RINGING ON THE LEFT SIDE OF THE SCREEN | CHECK/REPLACE C5001 FOR OPEN | |
| GE | 20GT420 | CTC146 | IMMEDIATE SHUTDOWN | CHECK/REPLACE CR3104 | |
| GE | 20GT420 | CTC146 | VERY LOW VOLUME AT MAXIMUM SETTING AND VERY LITTLE BASS. | CHECK/REPLACE U3300 | |
| GE | 20GT420 | CTC146 | TURN ON AND IMMEDIATE SHUT DOWN | CHECK/REPLACE CR4118 LEAKY | |
| GE | 20GT420 | CTC146 | HORZ OFF FREQ. AND HORZ. OUTPUTS KEEP SHORTING-- HORZ COLLASPE AND HORZ. OUTPUT IS RUNNING HOT | CHECK C4405 FOR LEAKAGE | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | ALL FUNCTIONS/CONTROLS ARE FROZEN | CHECK/REPLACE C3104 LEAKY | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | DEAD SET AFTER POWER SURGE BUT WORKS OK IF DEGAUSSING COIL IS UNPLUGGED - STANDBY VOLTAGES A LITTLE LOW | CHECK/REPLACE C3132 | |
| GE | 20GT420 | CTC146 | WILL NOT TUNE OR AUTOPROGRAM - MANUALLY SCANNING THROUGH CHANNELS LOOKS LIKE AFT OR TUNING PROBLEM. | CHECK/REPLACE IC U1001 | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420 | CTC146 | NO PICTURE - OSD AND AUDIO OK | CHECK/REPLACE R2602 | |
| GE | 20GT420 | CTC146 | WILL NOT AUTO-PROGRAM OR WILL NOT ADD TO CHANNEL MEMORY | CHECK/REPLACE C3302 (SMD) FOR LEAKAGE | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (177795) | |
| GE | 20GT420 | CTC146 | NO VERTICAL SWEEP OR INTERMITTENT VERTICAL SWEEP | CHECK/REPLACE Q4502 FOR LEAKY | |
| GE | 20GT420 | CTC146 | POOR REGULATION ALSO NARROW WIDTH | CHECK/REPLACE Q4102 (P/N# 193057) AND R4106 (P/N# 193068) | |
| GE | 20GT420 | CTC146 | AFTER WARM-UP PICTURE WOULD TURN GREENISH WITH RETRACE AND DEPRESSING 'DISPLAY' BUTTON WOULD CORRECT PROBLEM | CHECK/REPLACE C3118 (SMD) FOR LEAKAGE | |
| GE | 20GT420 | CTC146 | LOW REMOTE CTRL RANGE (APPROX 2 FEET) | CHECK IR WINDOW AND REPLACE IF YOU CANNOT SEE THROUGH | |
| GE | 20GT420 | CTC146 | TUNER FADING IN AND OUT - AFT DRIFTING | CHECK/RESOLDER CONNECTIONS ON JC17 | |
| GE | 20GT420 | CTC146 | SET WOULD TURN ON BUT WOULDN'T TURN OFF | CHECK/REPLACE C3127 FOR LEAKY | |
| GE | 20GT420 | CTC146 | DISTORTED AUDIO ON SOME CHANNELS-BLACK RASTER BUT A NEGATIVE PIX WILL SOMETIMES FLASH ON SCREEN. | CHECK R4106 FOR OPEN | |
| GE | 20GT420 | CTC146 | POWERS UP THEN SHUTS DOWN OR INTERMITTENT SHUTDOWN | CHECK CR4118 FOR OPEN | |
| GE | 20GT420 | CTC146 | LOW AUDIO DISTORTION | CHECK/REPLACE Q1201 | |
| GE | 20GT420 | CTC146 | IMMEDIATE SHUTDOWN | CHECK/REPLACE CR3104 | |
| GE | 20GT420 | CTC146 | NO VIDEO | CHECK/REPLACE Q2706 FOR SHORT | |
| GE | 20GT420 | CTC146 | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420 | CTC146 | FRONT BUTTONS BROKEN | CHECK/REPLACE BUTTON ASSY. (P/N# 206815) | |
| GE | 20GT420A01 | CTC146C | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A01 | CTC146C | MAKES CLICKING SOUND - NO SOUND AND NO PICTURE | CHECK/REPLACE CR4118 | |
| GE | 20GT420A01 | CTC146C | NO BRIGHTNESS CONTROL AND CONTRAST CONTROL SEEMS TO BRIGHTEN PICTURE. | CHECK/REPLACE R2715 AND R2728 | |
| GE | 20GT420A01 | CTC146C | INTERMITTENT VERTICAL SWEEP AND VERTICAL JITTER. | CHECK/REPLACE C4503 | |
| GE | 20GT420A01 | CTC146C | IMMEDIATE SHUTDOWN | CHECK/REPLACE CR3104 | |
| GE | 20GT420A01 | CTC146C | NO OSD | CHECK/REPLACE CR4124 FOR OPEN | |
| GE | 20GT420A01 | CTC146C | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT420A01 | CTC146C | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420A01 | CTC146C | NO REMOTE CONTROL FUNCTIONS | CHECK/REPLACE C3111 FOR LEAKAGE | |
| GE | 20GT420A01 | CTC146C | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A01 | CTC146C | AFTER WARM-UP PICTURE WOULD TURN GREENISH WITH RETRACE AND DEPRESSING 'DISPLAY' BUTTON WOULD CORRECT PROBLEM | CHECK/REPLACE C3118 (SMD) FOR LEAKAGE | |
| GE | 20GT420A01 | CTC146C | POOR CONTRAST AND VIDEO STREAKING,FLASHING OR SMEARED | CHECK/REPLACE DL2701 FOR LEAKAGE TO GROUND | |
| GE | 20GT420A01 | CTC146C | FRONT BUTTONS BROKEN | CHECK/REPLACE BUTTON ASSY. (P/N# 206815) | |
| GE | 20GT420A01 | CTC146C | PICTURE GOES DARK AFTER SET PLAY FOR A FEW MINUTES | CHECK/REPLACE R2602 | |
| GE | 20GT420A01 | CTC146C | NO PIX | CHECK/REPLACE Q2706 FOR LEAKAGE | |
| GE | 20GT420A01 | CTC146C | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420A01 | CTC146C | DARK RASTER | CHECK/REPLACE C3321 FOR LEAKAGE | |
| GE | 20GT420A01 | CTC146C | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420A01 | CTC146C | NO RASTER - CRT CUTOFF | CHECK/REPLACE Q2706 FOR LEAKY | |
| GE | 20GT420A01 | CTC146C | NO BRIGHTNESS CONTROL AND CONTRAST CONTROL SEEMS TO BRIGHTEN PICTURE. | CHECK/REPLACE R2715 AND R2728 | |
| GE | 20GT420A01 | CTC146C | WILL START TO AUTO PROGRAM THEN STOP ON CHANNEL 14 -- NO RECEPTION ON CHANNELS 7-13 | CHECK FOR OPEN TRACE BETWEEN R4128 AND JW26 | |
| GE | 20GT420A01 | CTC146C | BRIGHTNESS NORMAL AT TURN ON BUT THEN FADES OUT | CHECK/REPLACE R2715 | |
| GE | 20GT420A01 | CTC146C | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A01 | CTC146C | SOUND BUT NO RASTER - NO SCREEN VOLTAGE AT CRT | CHECK/REPLACE FOCUS/SCREEN CONTROL | |
| GE | 20GT420A04 | CTC146E | NO OSD | CHECK/REPLACE Q4501 FOR LEAKY | |
| GE | 20GT420A04 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420A04 | CTC146E | WILL TURN ON BUT WILL NOT TURN OFF-OSD MISSING-SOUND IS MISSING AND PIX IS MISSING | CHECK C3127 FOR LEAKAGE | |
| GE | 20GT420A04 | CTC146E | NO SOUND BUT PICTURE AND COLOR OK | CHECK/REPLACE R1211,R1209,R1210,Q1203 AND Q1202 | |
| GE | 20GT420A04 | CTC146E | NO OSD COLOR,JUST AN OUTLINE | CHEK/REPLACE C3318 FOR LEAKY | |
| GE | 20GT420A04 | CTC146E | HORIZONTAL BARS AT HIGH BRIGHTNESS | CHECK/REPLACE C2715 OR CONNECTIONS | |
| GE | 20GT420A04 | CTC146E | CHANNELS DRIFT OR WON'T TUNE PROPERLY | CHECK/REPLACE U3300 AND R3609 | |
| GE | 20GT420A04 | CTC146E | VERTICAL COMPRESSION AND FOLDED OVER AT THE TOP | CHECK/REPLACE IC U4501 | |
| GE | 20GT420A04 | CTC146E | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT420A04 | CTC146E | NO PICTURE - OSD AND AUDIO OK | CHECK/REPLACE R2602 | |
| GE | 20GT420A04 | CTC146E | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | NO SOUND BUT PICTURE AND COLOR OK | CHECK/REPLACE R1211,R1209,R1210,Q1203 AND Q1202 | |
| GE | 20GT420A04 | CTC146E | FRONT PANEL CONTROLS DO NOT WORK - REMOTE WORKS FINE | CHECK/REPLACE R3435 AND R3436 | |
| GE | 20GT420A04 | CTC146E | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | NO VIDEO - LOOKS LIKE A AGC PROBLEM | CHECK/REPLACE R2727 (3.9k) FOR OPEN | |
| GE | 20GT420A04 | CTC146E | AFTER WARM-UP PICTURE WOULD TURN GREENISH WITH RETRACE AND DEPRESSING 'DISPLAY' BUTTON WOULD CORRECT PROBLEM | CHECK/REPLACE C3118 (SMD) FOR LEAKAGE | |
| GE | 20GT420A04 | CTC146E | NO BRIGHTNESS CONTROL AND CONTRAST CONTROL SEEMS TO BRIGHTEN PICTURE. | CHECK/REPLACE R2715 AND R2728 | |
| GE | 20GT420A04 | CTC146E | NO VIDEO OR OSD | CHECK/REPLACE Q2706 | |
| GE | 20GT420A04 | CTC146E | NO PIX-SOUND OK-MISSING G1,G2 AND FOCUS VOLTAGES | CHECK/REPLACE FLYBACK TRANSFORMER | |
| GE | 20GT420A04 | CTC146E | ALL FUNCTIONS/CONTROLS ARE FROZEN | CHECK/REPLACE C3104 LEAKY | |
| GE | 20GT420A04 | CTC146E | DEAD SET OR INTERMITTENTLY SHUTS OFF | CHECK/REPLACE Q4102 | |
| GE | 20GT420A04 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420A04 | CTC146E | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | INTERMITTENTLY GOES OFF - RELAY CYCLES ON/OFF | CHECK/REPLACE CR4118 AND CR4121 | |
| GE | 20GT420A04 | CTC146E | INTERMITTENT SHUTDOWN OR SHUTSDOWN AT TURN ON | CHECK/REPLACE CR4118 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | WON'T TUNE PROPERLY-APPEARS TO BE A AFT PROBLEM | CHECK R3609 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | INTERMITTENTLY GOES OFF - RELAY CYCLES ON/OFF | CHECK/REPLACE CR4118 AND CR4121 | |
| GE | 20GT420A04 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420A04 | CTC146E | WILL NOT TUNE AND HAS REDUCED VERT AND LOW BRIGHTNESS | CHECK Q4106 - MAY CHECK GOOD OUT OF CIRCUIT | |
| GE | 20GT420A04 | CTC146E | BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE R4120 | |
| GE | 20GT420A04 | CTC146E | BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE R4120 | |
| GE | 20GT420A04 | CTC146E | DEAD SET WITH NO ATTEMPT TO START | CHECK/REPLACE Q3101 | |
| GE | 20GT420A04 | CTC146E | PICTURE GOES DARK AFTER SET PLAY FOR A FEW MINUTES | CHECK/REPLACE R2602 | |
| GE | 20GT420A04 | CTC146E | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | NO AUTO-PROGRAM | CHECK/RE-ADJUST R2323 FOR 5.9V AT PIN 42 OF U1001 | |
| GE | 20GT420A04 | CTC146E | AUTO PROGRAMMING STOPS AT 5,6 AND 7-13 -- HIGH CHANNELS ARE ALL OK | CHECK/REPLACE R126 (10 1/4w) | |
| GE | 20GT420A04 | CTC146E | OSD IS MISSING | CHECK Q4501 FOR LEAKAGE | |
| GE | 20GT420A04 | CTC146E | SET WILL START UP THEN SHUT DOWN | CHECK/REPLACE Q4102 | |
| GE | 20GT420A04 | CTC146E | SET COMES ON AND SHUTS DOWN IMMEDIATELY | CHECK/RESOLDER CONNECTIONS ON T4401 | |
| GE | 20GT420A04 | CTC146E | PICTURE GOES DARK AFTER SET PLAY FOR A FEW MINUTES | CHECK/REPLACE R2602 | |
| GE | 20GT420A04 | CTC146E | NO VIDEO AND NO COLOR SYNC | CHECK/REPLACE R2728 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420A04 | CTC146E | NO KEYBOARD FUNCTIONS - REMOTE CONTROL OPERATION NORMAL. | CHECK/REPLACE R3436 FOR OPEN | |
| GE | 20GT420N02 | CTC146E | WHEN A CHANNEL IS SELECTED IT IS NORMAL BUT THEN IT DRIFTS OFF - AUTO PROGRAM FEATURE WAS WORKING FINE. | CHECK/REPLACE U3300 | |
| GE | 20GT420N02 | CTC146E | DEAD SET | CHECK/REPLACE CR3102 FOR SHORTS | |
| GE | 20GT420N02 | CTC146E | VERTICAL FOLDOVER 1/3 WAY DOWN FROM THE TOP AND BOTTOM WAS PULLED UP - TOP STRETCHED | CHECK/REPLACE C4505 | |
| GE | 20GT420N02 | CTC146E | OSD MISSING - ONLY A BLACK BOX SHOWS UP | CHECK/REPLACE Q2903 FOR SHORT | |
| GE | 20GT420N02 | CTC146E | TURN ON AND IMMEDIATE SHUT DOWN | CHECK/REPLACE CR4118 LEAKY | |
| GE | 20GT420N02 | CTC146E | NO VERTICAL DEFLECTION | CHECK/REPLACE R4513,R4515 AND U4501 | |
| GE | 20GT420N02 | CTC146E | DEAD SET | CHECK/REPLACE LEAKY POWER SWITCH WHICH COULD BE ATTENUATING SCAN PULSES TO MICROPROCESSOR. | |
| GE | 20GT420N02 | CTC146E | WHEN SET WAS PLUGGED INTO AC IT WOULD COME ON AND WOULD NOT RESPOND TO ANY KEYS. | CHECK/REPLACE C3101 FOR LEAKY | |
| GE | 20GT420N02 | CTC146E | JAIL BARS ON THE LEFT SIDE OF PICTURE | CHECK/REPLACE C5001 ON THE CRT BOARD | |
| GE | 20GT420N02 | CTC146E | TURN ON AND IMMEDIATE SHUT DOWN | CHECK/REPLACE CR4118 LEAKY | |
| GE | 20GT420N02 | CTC146E | NO VERTICAL DEFLECTION | CHECK/REPLACE R4513,R4515 AND U4501 | |
| GE | 20GT420N02 | CTC146E | BLACK SCREEN--BRIGHTNESS CTRL. HAS NO EFFECT | CHECK R2715 FOR OPEN | |
| GE | 20GT420N02 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420N02 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420N02 | CTC146E | ALL FUNCTIONS ON THE TUNER CONTROL WERE REVERSED SUCH AS CHANNEL UP CAUSED CHANNEL DOWN TO ACTIVATE. | CHECK/REPLACE R3436 (100 ohms) FOR OPEN | |
| GE | 20GT420N04 | CTC146E | NO VERTICAL DEFLECTION | CHECK/REPLACE R4513,R4515 AND U4501 | |
| GE | 20GT420N04 | CTC146E | NO ON SCREEN DISPLAY (OSD) | CHECK/REPLACE CR4124 FOR OPEN | |
| GE | 20GT420N04 | CTC146E | NO PIX-SOUND OK-MISSING G1,G2 AND FOCUS VOLTAGES | CHECK/REPLACE FLYBACK TRANSFORMER | |
| GE | 20GT420N04 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420N04 | CTC146E | NO VHF OR UHF CHANNELS | CHECK/REPLACE CR4122 AND R4125 | |
| GE | 20GT420N04 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420N04 | CTC146E | ALL FUNCTIONS/CONTROLS ARE FROZEN | CHECK/REPLACE C3104 LEAKY | |
| GE | 20GT420N04 | CTC146E | PIX COMPRESSED AT THE TOP WITH RETRACE LINES - VERTICAL STRETCHED AT BOTTOM OF PIX. | CHECK/REPLACE CR4503 FOR LEAKY | |
| GE | 20GT420N04 | CTC146E | DEAD SET | CHECK/REPLACE Q4402 AND R4101 | |
| GE | 20GT420N04 | CTC146E | BLACK RASTER BUT OCCASIONALLY WOULD SHOW NEGATIVE VIDEO | CHECK/REPLACE R4106 FOR OPEN | |
| GE | 20GT420N04 | CTC146E | DEAD SET | CHECK/REPLACE CR3104,CR3102 | |
| GE | 20GT420N04 | CTC146E | NO PIX-NO OSD-HV OK AND SOUND OK | CHECK FOR DEFECTIVE SCREEN/FOCUS CONTROL | |
| GE | 20GT420N04 | CTC146E | NO VIDEO AND NO COLOR SYNC | CHECK/REPLACE R2728 FOR OPEN | |
| GE | 20GT420N04 | CTC146E | NO SOUND BUT PICTURE AND COLOR OK | CHECK/REPLACE R1211,R1209,R1210,Q1203 AND Q1202 | |
| GE | 20GT420N04 | CTC146E | NO AUTO-PROGRAMMING | ADJUST R2323 (AFT) FOR 5.9V AT PIN 42 OF U1001) | |
| GE | 20GT420N04 | CTC146E | NO PIX BUT HIGH VOLTAGE AND AUDIO ARE BOTH OK | CHECK/REPLACE R2727 FOR OPEN | |
| GE | 20GT425 | CTC146 | WILL NOT TURN ON AND 5v STAND-BY SOURCE WAS VERY LOW | CHECK/REPLACE U3300 SHORTED (PINS 4 & 29 OF U3300 WERE 20 ohms TO GROUND) | |
| GE | 20GT425 | CTC146 | IMMEDIATE SHUTDOWN | CHECK/REPLACE CR3104 | |
| GE | 20GT600 | CTC156 | NO AUTO-PROGRAMMING OF CHANNELS | CHECK/REPLACE CR4705 AND L4702 | |
| GE | 20GT604N01 | CTC156C | CHIRPING OR SQUEALING FROM POWER SUPPLY-PIX HAS WIGGLES OR SMALL HORZ. TEARING. | CHECK/REPLACE C4171 FOR BROKEN | |
| GE | 20GT604N01 | CTC156C | NO COLOR BUT ON-SCREEN COLOR INDICATOR DOES CHANGE | CHECK/REPLACE C2810,C2811 AND C2812 FOR LEAKY OR A CHANGE IN VALUE. | |
| GE | 20XT9006 | CTC168 | AUDIO HISS/AUDIO POP/NON-LINEAR VOLUME CONTROL | CHECK/REPLACE AUDIO CIRCUIT BOARD (205999) AND U3101 (206395) | |
| GE | 25GC701 | CTC157H | CHIRPING OR SQUEALING FROM POWER SUPPLY-PIX HAS WIGGLES OR SMALL HORZ. TEARING. | CHECK/REPLACE C4171 FOR BROKEN | |
| GE | 25GC703 | CTC167 | NO VERTICAL SWEEP | CHECK/REPLACE CR4501 | |
| GE | 25GC724 | CTC157 | POWER TURNS ON/OFF CONTINUOUSLY - SET WILL RUN AT 80 V AC | CHECK/REPLACE CR4160 IF 5V SUPPLY IS OVER 5 VOLTS | |
| GE | 25GC732 | CTC177 | SHUTS OFF INTERMITTENTLY | CHECK/REPLACE ON FLYBACK PINS, ESPECIALLY 1,2,8,10 | |
| GE | 25GT320 | CTC130A | DEAD - OPEN FUSE | CHECK/REPLACE C425 SHORTED | |
| GE | 25GT506 | CTC177 | DEAD SET | CHECK/REPLACE R4104 (1.5m @ 1/2w) | |
| GE | 25GT522 | CTC177 | DEAD SET - NO ATTEMPT TO START-UP | CHECK/REPLACE R4104 (1.5meg ) | |
| GE | 25GT536 | CTC177 | NO STEREO - OSD STEREO INDICATOR NEVER COMES ON | CHECK/REPLACE C1707 (P/N# 205230) | |
| GE | 25PC5843K | 25PC | SHORT VERTICAL SWEEP | CHECK/REPLACE C614 | |
| GE | 26GC100 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC100 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC100 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC100 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC100 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC100 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC100 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC100 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC100 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC100 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC100 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC100 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC100 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC100 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC100 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC100 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC100 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC100 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC100 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC100 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC100 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC100 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC100 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC100 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC100 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC100 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC100 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC100 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC100 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC100 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC100 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC100 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC100 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC100 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC100 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC100 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC400 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC400 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC400 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC400 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC400 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC400 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC400 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC400 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC400 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC400 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC400 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC400 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC400 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC400 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC400 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC400 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC400 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC400 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC400 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC400 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC400 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC400 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC400 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC400 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC400 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC400 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC400 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC400 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC400 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC400 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC400 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC400 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC400 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC400 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC400 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC400 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC400 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC400 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC400 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC401 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC401 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC401 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC401 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC401 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC401 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC401 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC401 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC401 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC401 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC401 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC401 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC401 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC401 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC401 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC401 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC401 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC401 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC401 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC401 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC401 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC401 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC401 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC401 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC401 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC401 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC401 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC401 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC401 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC401 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC401 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC401 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC480 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC480 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC480 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC480 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC480 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC480 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC480 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC480 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC480 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC480 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC480 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC480 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC480 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC480 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC480 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC480 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC480 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC480 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC480 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC480 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC480 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC480 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC480 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC480 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC480 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC480 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC480 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC480 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC480 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC480 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC480 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC480 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC480 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC480 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC480 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC480 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC480 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC480 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC480 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC480 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC480 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC480 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC480 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC480 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC480 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC481 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC481 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC481 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC481 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC481 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC481 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC481 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC481 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC481 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC481 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC481 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC481 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC481 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC481 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC481 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC481 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC481 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC481 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC481 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC481 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC481 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC481 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC481 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC481 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC481 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC481 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC481 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC481 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC481 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC481 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC481 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC481 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC481 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC481 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC481 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC482 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC482 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC482 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC482 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC482 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC482 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC482 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC482 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC482 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC482 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC482 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC482 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC482 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC482 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC482 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC482 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC482 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC482 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC482 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC482 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC482 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC482 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC482 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC482 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC482 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC482 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC482 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC482 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC482 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC482 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC482 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC482 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC482 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC482 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC482 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC482 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC482 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC482 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC482 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC482 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC482 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC482 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | EXCESSIVE COLOR WITH NO CONTROL | CHECK/REPLACE U1001 | |
| GE | 26GC640 | CTC149 | NO VIDEO - INTERMITTENT VIDEO OR POOR VIDEO - AUDIO OK | CHECK/REPLACE DL2701 DELAY LINE (153674) | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC640 | CTC149 | FUSE BLOWS INTERMITTENTLY | CHECK/REPLACE C4403 FOR INTERMITTENT SHORT | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE U4101 | |
| GE | 26GC640 | CTC149 | INTERMITTENT START-UP AT NORMAL LINE VOLTAGE | CHECK/REPLACE C4302 AND Q4301 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC640 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC640 | CTC149 | DEAD SET WITH Q4401 SHORTED | CHECK/REPLACE Q4401 AND CONNECTIONS ON Q4601 | |
| GE | 26GC640 | CTC149 | NO CONTROL OF BRIGHTNESS - HIGH BRIHGTNESS | CHECK/REPLACE C2703 FOR LEAKAGE | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | OSD HAS STRANGE GRAPHIC CHARACTERS | CHECK/REPLACE U3300 | |
| GE | 26GC640 | CTC149 | VERTICAL LINES OR RINGING ON THE LEFT SIDE OF SCREEN | CHECK/REPLACE R4403 | |
| GE | 26GC640 | CTC149 | NO VERTICAL DEFLECTION OR SHORT SWEEP | CHECK/REPLACE R4510,R4512 AND Q3108 | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC640 | CTC149 | RANDOM FAILURES OF HORZ. OUTPUT XSTR. | CHECK/REPLACE C4316 FOR OPEN | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | SET TURNS ON INTERMITTENT AND OSD HAS SEVERAL LINES OF SCRAMBLED LETTERS. | CHECK/RESOLDER CONNECTIONS ON R3123 | |
| GE | 26GC640 | CTC149 | DEAD SET - STANDBY VOLTAGES ARE LOW | CHECK/REPLACE U4101 | |
| GE | 26GC640 | CTC149 | DEAD SET - WEAK OR NO SIGNAL | CHECK/REPLACE C4302 FOR OPEN | |
| GE | 26GC640 | CTC149 | SET COMES ON BUT NO OSD OR PICTURE - AUDIO OF ONE CHANNEL CAN BE HEARD | CHECK/REPLACE CR4703 AND L4703 | |
| GE | 26GC640 | CTC149 | VERTICAL BLANKING BAR WOULD OCCASSIONALLY ROLL THRU PICTURE | CHECK/REPLACE U1001 | |
| GE | 26GC640 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC640 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC640 | CTC149 | DEAD SET - NO ATTEMPT TO START UP | CHECK/REPLACE Q4301 OPEN | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | SYSTEM CONTROL PROBLEMS - NO CONTROL OF VOLUME AND KEYBOARD LOCKS UP. | CHECK/REPLACE Q3103 | |
| GE | 26GC640 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | VERT. LINES,JAIL BARS OR RINGING ON LEFT SIDE OF PIX | CHECK/REPLACE R4403 FOR OPEN | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORTS | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC640 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | OSD HAS NORMAL CHARACTERS AS WELL AS TRASH | CHECK/REPLACE U3300 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC640 | CTC149 | DEAD SET AND WILL NOT START AT NORMAL LINE VOLTAGE | CHECK/REPLACE CR4708 AND CR3104 | |
| GE | 26GC640 | CTC149 | HORZ. OUTPUT FAILS FOR NO APPARENT REASON | CHECK/REPLACE C4316 FOR OPEN OR INTERMITTENT | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORTS | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | LINES AT TOP AND BOTTOM OF THE PIX | CHECK/REPLACE Q4401 FOR LEAKAGE | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | DEAD SET AND BLOWING F4001 | CHECK/REPLACE C4403 FOR SHORTS | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | SET PULSES FOR 3 TO 5 SECONDS THEN SHUTSDOWN | CHECK/REPLACE CR4704 FOR SHORT | |
| GE | 26GC640 | CTC149 | NO COLOR | CHECK/REPLACE C2804 FOR SHORT | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | ERRATIC LINES AT TOP AND BOTTOM OF PIX AFTER WARM-UP | CHECK/REPLACE Q4401 | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | WILL NOT AUTO PROGRAM CHANNELS - WHEN MANUALLY SELECTING CHANNELS WITH REMOTE,LOOKS LIKE AFT IS WAY OFF | CHECK/REPLACE IC U1001 (193082) | |
| GE | 26GC640 | CTC149 | VERTICAL FOLDOVER | CHECK/REPLACE R4511 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE IMMEDIATELY | CHECK/REPLACE Q4401 AND T4401 FOR SHORT | |
| GE | 26GC640 | CTC149 | NO AUDIO OR VERY LOW AUDIO | CHECK/REPLACE C1925 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | DEAD SET WITH F4001 OPEN | CHECK/REPLACE C4403 FOR SHORT | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | WILL NOT TURN ON OR OFF | CHECK/RESOLDER CONNECTIONS ON R3121 (MISSING 60Hz TO PIN 37 OF U3100) | |
| GE | 26GC640 | CTC149 | AUDIO BUZZES ON SOME CHANNELS OR DISTORTED | CHECK CF FILTER ON PIN 35 OF U1001 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC640 | CTC149 | NO AUTOPROGRAMMING-CHANNELS WOULD TUNE WITH THE REMOTE BUT WERE SLOW TO LOCK IN. | CHECK/ADJUST L2306 | |
| GE | 26GC640 | CTC149 | INTERMITTENT AUDIO | CHECK/RESOLDER CONNECTIONS BETWEEN R2338 AND JC18 | |
| GE | 26GC640 | CTC149 | AUDIO IS DISTORTED ON SOME CHANNELS | CHECK/REPLACE CF1201 | |
| GE | 26GC640 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC640 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC640 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC640 | CTC149 | INTERMITTENT SOUND FAILURE WITH SET COLD | CHECK/REPLACE R1 IN AUDIO POWER SUPPLY | |
| GE | 26GC640 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC640 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC640 | CTC149 | NO COLOR | CHECK/REPLACE C2808 AND C2817 | |
| GE | 26GC641 | CTC149 | VERTICAL COLLASPE INTERMITTENT WHEN CHANGING CHANNELS | CHECK/REPLACE R3133 (SMD) | |
| GE | 26GC641 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC641 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC641 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC641 | CTC149 | WON'T PROGRAM OR TUNE LOWER CHANNELS EVEN WITH HAND UNIT | CHECK/REPLACE U3300 | |
| GE | 26GC641 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC641 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC641 | CTC149 | WHEN COLD, SET HAS POOR REGULATION AND HORZ. TEARING OR PIE CRUSTING | CHECK/REPLACE CR4709 FOR INTERMITTENT | |
| GE | 26GC641 | CTC149 | NO START UP ON NORMAL AC LINE VOLTAGE (COULD BE INTERMIT.) | CHECK/REPLACE CR4302 FOR OPEN | |
| GE | 26GC641 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC641 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC641 | CTC149 | SHORT VERTICAL SWEEP OR NO VERTICAL SWEEP | CHECK/REPLACE L4703,R4506 AND U4501 | |
| GE | 26GC641 | CTC149 | SET SHUTS DOWN AFTER ABOUT 5 SECONDS | CHECK/REPLACE CR4704 FOR SHORTS | |
| GE | 26GC641 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 | |
| GE | 26GC641 | CTC149 | WILL NOT AUTO-PROGRAM ALL CHANNELS-MAY SKIP ONE OR MORE CHANNELS OR MAY INTERMITTENTLY CHANGE CHANNELS | CHECK/REPLACE U3300 | |
| GE | 26GC641 | CTC149 | DEAD SET | CHECK/REPLACE CR4301 AND Q4301 | |
| GE | 26GC641 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC641 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC641 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC641 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC641 | CTC149 | INTERFERENCE IN THE RASTER AND HORZ. OUTPUT SHORTS - SET HAD INTERMITTENT FLAGGING ABOUT 1/2 WAY DOWN SCREEN | CHECK/REPLACE U4101 | |
| GE | 26GC641 | CTC149 | CLOCK RUNS TOO FAST | CHECK/REPLACE C3112 FOR OPEN OR MISSING | |
| GE | 26GC641 | CTC149 | DEAD SET | CHECK/REPLACE SCR4101 | |
| GE | 26GC641 | CTC149 | BRIGHTNESS TOO HIGH WITH RETRACE LINES | CHECK/REPLACE CR5001 FOR LEAKAGE | |
| GE | 26GC641 | CTC149 | BLOWS FUSE QUICK-LOW RESISTANCE ON HORZ. TO GRD. | CHECK FOR SHORTED C403 | |
| GE | 26GC641 | CTC149 | DEAD SET | CHECK/REPLACE CR4102 FOR SHORT | |
| GE | 26GC641 | CTC149 | SOUND IS OK BUT NO VIDEO | CHECK IC U1001 |
|
LAMSON
Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675 TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:lamsonsm@gmail.com
YAHOO MESSENGER ID : myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be
using the old address and phone no. in the future. Please be
noted when calling us, sending letters, parcels or buying our products>
|
