TV REPAIR TIPS PAGE 13

MAKE	MODEL	CHASSIS	SYMPTOM	CURE
PHILIPS	N/A	13C5	HUM BAR BUT WITHOUT SHADING - WORSE AT HIGH BRIGHTNESS	CHECK/REPLACE D425 FOR LEAKAGE
PHILIPS	N/A	13C5	VERY LITTLE SOUND AND NO PICTURE-BRIGHT RASTER W/RETRACE	CHECK/REPLACE D408 AND R408
PHILIPS	N/A	13C5	NO START UP VOLTAGE	D461 OPEN OR LEAKY
PHILIPS	N/A	13C5	DARK SCREEN NO VIDEO	CHANGED C425
PHILIPS	N/A	13C5	B+ ABOUT 100V-WILL ADJUST BUT NOT TO 130V	CHECK D581 (5.6V ZENER) FOR LEAKAGE
PHILIPS	N/A	13C5	DELAYS LOCKING ONTO CHANNEL AND LOOKS LIKE TUNER	CHECK/REPLACE IC340 (ALSO CHECK FOR COINCIDENCE PULSE AT PIN #13 OF IC340)
PHILIPS	N/A	13C5	NO VIDEO OR BRIGHT. UNLESS MASTER SCRN. RAISED	CHECK C425
PHILIPS	N/A	13C5	DEAD SET-NO REG B+	CHECK IC340 FOR SQR.WAVE @ PIN#11--REPLACE IF MISSING
PHILIPS	N/A	13D5	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	13D5	INTERMITTENT OR MISSING ONE PRIMARY COLOR	CHECK/REPLACE Q21,Q22 OR Q23 ON CRT BOARD - MAY BE LABELED AS Q1,Q2,Q3 (P/N# 483513047059)
PHILIPS	N/A	13D5	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	13P5	VIDEO SMEARS ON BRIGHT OBJECTS	ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND
PHILIPS	N/A	13Y1	NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE	CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831)
PHILIPS	N/A	13Y1	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	15C3	VERTICAL COMPRESSION AND SLIGHT STRETCH IN THE CENTER WHEN CHANNELS ARE CHANGED AND BOUNCE ON SCENE CHANGES.	CHECK/REPLACE C510
PHILIPS	N/A	15C3	DEAD SET	CHECK FOR OPEN R417,R418
PHILIPS	N/A	15C3	INTERM, PIX-CHANNEL INDIC. BLINKS OFF/ON	CHECK FOR DEFECTIVE C474
PHILIPS	N/A	15C3	DEAD SET	CHECK/RESOLDER CONNECTION ON R466
PHILIPS	N/A	15C3	VERTICAL IS COMPRESSED BUT SLIGHTLY STRETCHED IN THE MIDDLE	CHECK/REPLACE C510
PHILIPS	N/A	15C3	SOFT VERT. BOUNCE	CHECK C510
PHILIPS	N/A	15C3	DEAD SET	CHECK/RESOLDER CONNECTIONS ON R466
PHILIPS	N/A	19C4	SET SHUTSDOWN	CHECK/REPLACE C506,R522 OR R516
PHILIPS	N/A	19C4	GOES OFF FOR NO APPARENT REASON	CHECK/RESOLDER CONNECTIONS ON T601,T700 AND HORZ. OUTPUT SOCKET
PHILIPS	N/A	19C5	NO START UP VOLTAGE	D461 OPEN OR LEAKY
PHILIPS	N/A	19C5	DEAD SET-NO REGULATOR B+	CHECK IC340 FOR SQR.WAVE AT PIN #11-REPL. IF MISSING
PHILIPS	N/A	19C5	NO BLUE	CHECK/REPLACE R245,R233,IC150
PHILIPS	N/A	19C5	VERY LITTLE SOUND AND NO PICTURE-BRIGHT RASTER W/RETRACE	CHECK/REPLACE D408 AND R408
PHILIPS	N/A	19C5	DEAD SET	CHECK/REPLACE Q401,Q464,T408,T453,IC340,IC331,C338,C470, D404,D461,D459,IC469,Q463,Q457,Z481,Q470,Q471,Q494,R339
PHILIPS	N/A	19C5	NO HORZ.SYNC	CHECK/REPLACE R50 AND L405
PHILIPS	N/A	19C5	NO VERTICAL SYNC	CHECK/REPLACE IC340
PHILIPS	N/A	19C5	VERTICAL FOLDOVER,JITTER OR NO SWEEP	CHECK/REPLACE C321,Z481,IC331,IC340,R420,D420C322,L414,R328
PHILIPS	N/A	19C5	DARK SCREEN-NO VIDEO--SOUND AND HIGH VOLTS OK	CHECK C425
PHILIPS	N/A	19C5	NO VIDEO	CHECK/REPLACE IC331,IC340,IC51,Q158,R408,R414,R410
PHILIPS	N/A	19C5	SHORT VERTICAL SWEEP	CHECK/REPLACE R420 (MAY CHECK GOOD OUT OF CIRCUIT)
PHILIPS	N/A	19C5	SET SHUTS OFF WITH AC BELOW 110 VOLTS	CHECK/REPLACE C458
PHILIPS	N/A	19C5	DELAYS LOCKING ONTO CHANNEL AND LOOKS LIKE TUNER	CHECK/REPLACE IC340 (ALSO CHECK FOR COINCIDENCE PULSE AT PIN #13 OF IC340)
PHILIPS	N/A	19C5	NO VIDEO OR BRIGHT. UNLESS MASTER SCRN. RAISED	CHECK C425
PHILIPS	N/A	19C5	NO SOUND AND POOR PICTURE - APPEARS TO HAVE ARCING IN THE PICTURE	CHECK/REPLACE D408 AND R408
PHILIPS	N/A	19C5	SET SHUTS DOWN ON LOW AC LINE VOLTAGE	CHECK/REPLACE C458
PHILIPS	N/A	19C5	DEAD SET (USUALLY AFTER A STORM)	CHECK/REPLACE IC1000
PHILIPS	N/A	19C5	RINGING IN THE PIX	CHECK/REPLACE Q156,Y151,Z481,SF38
PHILIPS	N/A	19C5	ARCING IN THE PICTURE OR POOR FOCUS	CHECK/REPLACE R255 AND T408
PHILIPS	N/A	19C5	HUM BAR BUT WITHOUT SHADING - WORSE AT HIGH BRIGHTNESS	CHECK/REPLACE D425 FOR LEAKAGE
PHILIPS	N/A	19C5	HORIZONTAL BENDING	CHECK/REPLACE D425
PHILIPS	N/A	19C5	NO RED OR HAS RED RASTER	CHECK/REPLACE IC150
PHILIPS	N/A	19C5	B+ ABOUT 100V-WILL ADJUST BUT NOT TO 130V	CHECK D581 (5.6V ZENER) FOR LEAKAGE
PHILIPS	N/A	19C5	NO SOUND OR PIX	CHECK D461 FOR LEAKAGE (MAY CHECK GOOD FRONT TO BACK)
PHILIPS	N/A	19C5	NO COLOR OR NO COLOR SYNC	CHECK/REPLACE IC150,Y194,SF38,C182,C185,C174,Q35,C180
PHILIPS	N/A	19C5	RETRACE LINES IN THE PICTURE	CHECK/REPLACE IC150,Q226,Q240
PHILIPS	N/A	19C6	DEAD SET	REPLACED Q321,Z370
PHILIPS	N/A	19C6	RETRACE LINES IN PIX	CHECK/REPLACE C303,R56,IC50,IC320,IC300,Q11,Q31,Q51
PHILIPS	N/A	19C6	INTERMITTENT OR COMPLETE SHUTDOWN	CHECK/RESOLDER CONNECTIONS ON C550
PHILIPS	N/A	19C6	DEAD SET	CHECK/REPLACE Q400,D400,D401,D402,D403,Q401,R420,R408, IC403,D430,Z407,R402,R403,C411,Z436,R431
PHILIPS	N/A	19C6	NO RASTER	REPLACED CRT
PHILIPS	N/A	19C6	NO HIGH VOLTAGE	CHECK/REPLACE D461,Q464,Q463,T465,T460,IC320,R434,R435, R337,R464,R428,Q461,D462
PHILIPS	N/A	19C6	MISSING ONE COLORS	CHECK/REPLACE IC50,Q11,Q31,Q51
PHILIPS	N/A	19C6	DEAD SET	REPLACED R434,D433
PHILIPS	N/A	19C6	Q501 OVERHEATS/SHORTS--APPEARS FLYBACK SHORTED	CHECK R503 (47 OHM) FOR OPEN OR HIGH RESISTANCE
PHILIPS	N/A	19C6	HUM IN AUDIO	REPLACED D170
PHILIPS	N/A	19C6	DEAD SET OR INTERMITTENT POWER	CHECK T400 CONNECTIONS
PHILIPS	N/A	19C6	DISTORTED VERTICAL AT TOP AND BOTTOM	CHECK/REPLACE RESISTOR LOCATED ON THE ANODE SIDE OF D1 ON THE PINCUSHION MODULE.
PHILIPS	N/A	19C6	VOLUME AND CHANNELS CHANGE BY THEMSELVES	REPLACE 4.0MHz CRYSTAL
PHILIPS	N/A	19C6	DEAD SET-NO REG B+	CHECK IC340 FOR SQR.WAVE @ PIN#11--REPLACE IF MISSING
PHILIPS	N/A	19C6	DEAD SET-GRD. BASE OF Q402 AND SET COMES ON	CHECK/REPLACE IC403
PHILIPS	N/A	19C6	NO VIDEO	CHECK/REPLACE IC601,R434,R435,IC50,Q54,IC10,R56
PHILIPS	N/A	19C6	ARCING IN CRT OR IN VIDEO	CHECK/REPLACE T465
PHILIPS	N/A	19C6	DEAD SET	REPLACED C466,AND IC1200
PHILIPS	N/A	19C6	JAPANESE CHARACTERS AFTER REPLACING IC1200	CHECK/REPLACE IC1200 - MAKE SURE NUMBER ON IC IS MN1277B
PHILIPS	N/A	19C6	ON MODELS WITH 10 WATT AMP, A LOUD THUMP IS HEARD WHEN TURNING SET ON.	CHECK/REPLACE D170 AND CHANGE C163 FROM 330uF TO 1000uF
PHILIPS	N/A	19C6	NO COLOR	CHECK/REPLACE IC50,Y50,IC10,R50,R435,C66,IC320,R56
PHILIPS	N/A	19C6	PICTURE OVER SCANS VERTICALLY AND HORIZONTALLY	CHECK Q464 FOR SHORTS -- ESPECIALLY IF SAFTEY CAP.
PHILIPS	N/A	19C7	INTERMITTENT SHUTDOWN	CHECK/REPLACE FLYBACK XFRM. - POSSIBILITY OF STATIC BUILD UP IN THE FLYBACK CORE.
PHILIPS	N/A	19C7	INTERMITTENT SHUTDOWN	CHECK/REPLACE FLYBACK TRANSFORMER FOR STATIC BUILD UP INSIDE THE CORE. ARCING CAN BE HEARD FAINTLY
PHILIPS	N/A	19C7	COLOR TINT SHIFT AT TOP OF BARS	CHECK Q601 FOR SHORTS
PHILIPS	N/A	19C7	WILL NOT TURN OFF IN THE CABLE MODE BUT NORMAL MODE IS OK- CHANNELS WILL NOT CHANGE BUT LED'S BLINK	CHECK/REPLACE D308 FOR SHORT
PHILIPS	N/A	19C8	LOUD WHISTLE WHEN SET IS OFF-OTHERWISE NORMAL	CHECK R430 (56 OHM) FOR OPEN
PHILIPS	N/A	19C8	DEAD SET	CHECK/REPLACE Q406
PHILIPS	N/A	19C8	INTERMITTENT SOUND OR FULL VOLUME WITH NO CONTROL	CHECK/RESOLDER ALL CONNECTIONS ON THE BOTTOM OF THE 'IF' CAGE TO THE PCB.
PHILIPS	N/A	19C8	SHUTDOWN,130V NOT REGULATING OR NOT HIGH ENOUGH	CHECK IC201,IC580,Q400,SCR401,Q402,Q403,Q406,Q407,
PHILIPS	N/A	19C8	DEAD SET	CHECK/REPLACE T500 (HORZ. DRIVER XFRM)
PHILIPS	N/A	19C8	DEAD SET	CHECK R434 FOR OPEN
PHILIPS	N/A	19C8	HERRINGBONE,VERT.JITTER,INT.COLOR,DOUBLE IMAGE	CHECK/REPLACE IC201
PHILIPS	N/A	19C8	DEAD SET BUT POWER LED COMES ON WHEN POWER BUTTON IS PUSHED	CHECK/REPLACE Z408 FOR SHORT
PHILIPS	N/A	19C8	POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT	CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068)
PHILIPS	N/A	19C8	DEAD SET	CHECK/REPLACE D414,D416,Q406 AND Q407
PHILIPS	N/A	19C8	INTERMITTENT LOSS OF HORZ. HOLD AND PIX SHRINKS HORZ.	CHECK R505 FOR CONNECTIONS PROBLEMS
PHILIPS	N/A	19C8	NO STANDBY VOLTAGES	REPLACED R407/INDUCTOR L402
PHILIPS	N/A	19C8	BRIGHT SCREEN W/RETRACE - SHORT VERT. - AUDIO IS NORMAL	CHECK R510 FOR OPEN
PHILIPS	N/A	19C8	PIX SHIFTED TO RIGHT,4' BLACK BAR ON LEFT SIDE	CHECK R508 FOR BREAKING DOWN UNDER LOAD
PHILIPS	N/A	19C8	DARK PIX. IN LEFT SIDE	REPLACED C508
PHILIPS	N/A	19C8	NO PIX-RASTER AND SOUND OK	CHECK C642 SHORTED
PHILIPS	N/A	19C8	WHITE SMOOTH RASTER (NO VIDEO) - SOUND OK	CHECK/REPLACE C631 AND IC640
PHILIPS	N/A	19C8	INTERMITTENT PIX-BLACKS OUT-AUDIO LEVEL DROPS	CHECK ALL CONNECTIONS ON T500
PHILIPS	N/A	19C8	DEAD SET-NO REG B+	CHECK IC340 FOR SQR. WAVE @ PIN #11--IF MISSING REPL.
PHILIPS	N/A	19C8	DEAD SET - STANDBY VOLTAGE IS TOO HIGH AND FULL POWER IS SLIGHTLY HIGH (132 VOLTS)	CHECK/REPLACE Q500
PHILIPS	N/A	19C8	BRIGHT RASTER WITH RETRACE AND DIM VIDEO	CHECK/REPLACE R25 (CRT BOARD)
PHILIPS	N/A	19C8	POOR SOUND FROM LEFT SPEAKER WITH EXPANDED SOUND SWITCH ON.	CHECK/REPLACE IC400 ON THE STEREO DECODER BOARD.
PHILIPS	N/A	19C8	DEAD SET-POWER SUPPLY IS OK-NO HORZ. DRIVE	CHECK IC201 AND Q500
PHILIPS	N/A	19C8	POOR SOUND FROM LEFT SPKR WITH SOUND EXPAND ON	REPLACE IC400 ON THE SAP BOARD
PHILIPS	N/A	19C8	VOLUME AT FULL MVOL THE TUNER BEGINS CHANNEL SER	REPLACE IC280
PHILIPS	N/A	19C8	DEAD SET--NO HORZ. DRIVE	CHECK Q500
PHILIPS	N/A	19C8	PICTURE SIZE VARIES BOTH HORZ. AND VERT.	CHECK/REPLACE C421
PHILIPS	N/A	19C8	NO SOUND - AFTER REPLACING IC280 IT RUNS VERY WARM	CHECK/REPLACE IC280,R284 AND C287
PHILIPS	N/A	19C8	DEAD SET AFTER INSTALLATION OF IC404	CHECK FOR PROPER ORIENTATION OF IC404 - SOME BOARDS WERE MARKED WRONG WITH RESPECT TO PIN#1 OF THE IC.
PHILIPS	N/A	19C8	INTERMITTENT BRIGHTNESS VARIATIONS	CHECK/REPLACE R25 ON CRT BOARD
PHILIPS	N/A	19C8	PIX BREAKS UP,BLOOMS,AND VERT SIZE DECREASES	CHECK Q406,Q407 AND Z436 FOR SHORTS
PHILIPS	N/A	19C8	WHEN BRIGHTNESS INCREASES,PIX SHRINKS VERTICALLY	CHECK D416 FOR OPEN (OUT OF CIRCUIT)
PHILIPS	N/A	19C8	DEAD SET - PIN#26 OF IC201 IS SHORTED TO GROUND.	CHECK/REPLACE Z436
PHILIPS	N/A	19C8	NO VOLUME CTRL.--DOESN'T MUTE ON CHANNEL CHANGE	CHECK IC280
PHILIPS	N/A	19C8	GARBLED SOUND AND POSSIBLY ONLY ON CERTAIN CHANNELS	CHECK/REPLACE Y201 SAW FILTER (P/N 483515497069)
PHILIPS	N/A	19C8	BLANK RASTER OR SLICK RASTER-SOUND OK	CHECK/REPLACE IC580 (VERT OUTPUT)
PHILIPS	N/A	19C8	TUNER CONT TO SEARCH AFTER THE CHANNEL IS SELECT	RESOLDERED IC309
PHILIPS	N/A	19C8	BRIGHT SCREEN WITH NO VIDEO - OSD LOOKS LIKE THE HORZ. PHASE IS OFF AS GRAPHICS ARE SHIFTED	CHECK/REPLACE R501 OR R502 FOR OPEN
PHILIPS	N/A	19C8	PICTURE IS SHIFTED 8 TO 10 INCHES TO THE RIGHT - HORZ. BLANKING BAR IS IN THE CENTER OF THE SCREEN	CHECK/REPLACE R501 AND R502 FOR OPEN
PHILIPS	N/A	19C8	Q501 OVERHEATS/SHORTS--APPEARS FLYBACK SHORTED	CHECK R503 (47 OHM) FOR OPEN OR HIGH RESISTANCE
PHILIPS	N/A	19C8	NO VIDEO OR LUMINANCE	CHECK/REPLACE LEAKY HORZ.DRIVER XSTR.
PHILIPS	N/A	19C8	NO VIDEO WITH RETRACE LINES	CHECK D500 FOR LEAKAGE (WILL CHECK GOOD)
PHILIPS	N/A	19C9	DEAD SET BUT POWER LED COMES ON WHEN POWER BUTTON IS PUSHED	CHECK/REPLACE Z408 FOR SHORT
PHILIPS	N/A	19C9	POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT	CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068)
PHILIPS	N/A	19C9	POOR PICTURE RECEPTION	CHECK/REPLACE Y200 (SAW FILTER)
PHILIPS	N/A	19F1	NO VIDEO	CHECK/REPLACE D640
PHILIPS	N/A	19F1	NO COLOR	CHECK/REPLACE Q640
PHILIPS	N/A	19F1	NO VIDEO	CHECK/REPLACE Y609
PHILIPS	N/A	19F1	NO COLOR	CHECK/REPLACE R638
PHILIPS	N/A	19F1	SNOWY RASTER AND AUDIO FROM ONE CHANNEL IS ALL THAT CAN BE HEARD - CHANNEL NUMBER DOES CHANGE	CHECK/REPLACE TUNER OR PRESCALER IC INSIDE TUNER IC - (P/N# 483520987893)
PHILIPS	N/A	19F1	HORZ. FREQUENCY DRIFTS	CHECK/REPLACE R247
PHILIPS	N/A	19G6	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE F401 (P/N# 483525397031) AND Q501 (P/N# 483513067001)
PHILIPS	N/A	19G6	DEAD SET	CHECK/REPLACE Q410 (P/N# 483513047051) AND IC410 (P/N# 483520947056)
PHILIPS	N/A	19G6	TV IS STUCK IN THE DEMONSTRATION MODE	PRESS VOLUME UP/VOLUME DOWN AT THE SAME TIME TO END DEMO
PHILIPS	N/A	19G6	LOW AUDIO BUZZ OR HUM WITH VOLUME SET TO MINIMUM	INSTALL JUMPERS AT B-31 AND B-22
PHILIPS	N/A	19G6	REMOTE NOT WORKING	CHECK/REPLACE IR91 (P/N# 483521947267)
PHILIPS	N/A	19G6	OSD IS SHIFTED TO THE LEFT	CHECK/REPLACE IC346 (P/N# 483520988108)
PHILIPS	N/A	19G6	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	ADD 1.2m?(P/N# 483511057204) FROM PIN #11 TO PIN #16 OF IC270
PHILIPS	N/A	19G6	SET WON'T TURN ON	CHECK/REPLACE Q402 (P/N# 483513047059)
PHILIPS	N/A	19G6	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19G6	NO AUDIO	CHECK/REPLACE IC230 (P/N# 483520947005)
PHILIPS	N/A	19G6	NO PICTURE - BLANK RASTER	CHECK/REPLACE IC550 AND R460 (P/N# 483511687082)
PHILIPS	N/A	19G6	REPEATED HORZ. OUTPUT FAILURE	CHANGE Q501 WITH (483513041782), R502 W/2k (483511657409), INSTALL C509 (483512247008) & DIODE/RES. KIT (483521957539)
PHILIPS	N/A	19G6	NO PICTURE	CHECK/REPLACE Z461 (P/N# 483513037068)
PHILIPS	N/A	19G6	VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL	CHECK/REPLACE R222 OPEN (12k? (P/N# 483511657397)
PHILIPS	N/A	19G6	INTERMITTENTLY REMOTE DOESN'T WORK OR SET LOCKS UP	CHECK/REPLACE MICROPROC. W/NEW TYPE IC (P/N# 483520988291)
PHILIPS	N/A	19G6	SET WON'T TURN OFF	CHECK/REPLACE IC410 (P/N# 483520947056)
PHILIPS	N/A	19G6	NO PICTURE AND NO HIGH VOLTAGE	CHK/REPL. Q501 (P/N# 483513047073),Q502 (P/N# 483513067001) ALSO CHECK CONNECTIONS ON FLYBACK AND HORZ. DRIVER XFRM.
PHILIPS	N/A	19G6	WILL NOT TUNE ANY CHANNELS	CHECK/REPLACE R360/R361 (15k 1/2w.) AND Z361 (33v ZENER)
PHILIPS	N/A	19G6	DEAD SET	CHECK/REPLACE R403 (P/N# 483511237024) AND D401-D404 (P/N# 482213041275), R501 (P/N# 483511657408)
PHILIPS	N/A	19J4	WASHED OUT VIDEO - COLORS SMEAR WHEN ADJUSTING THE CUTOFF CONTROLS	CHECK/REPLACE Q641,Q642 AND Q643 FOR E-B SHORT
PHILIPS	N/A	19J4	AUD. OUT FAILURE--C211 TO 1uF C206 TO 470pF	PARALLEL R202 W/470pF R207 10 OHM R213,214 130 OHM
PHILIPS	N/A	19L1	DEAD SET	CHECK Y320 (4MHz XTAL)
PHILIPS	N/A	19L1	SET TURNS ON BY ITSELF OR CANNOT BE TURNED OFF	CHECK/REPLACE D414 FOR LEAKAGE USE 483513037048)
PHILIPS	N/A	19L1	BRIGHT SCREEN WITH RETRACE LINES - G1 WILL NOT CORRECT	CHECK/REPLACE R460,D460 AND C461
PHILIPS	N/A	19L1	MAY NOT START AT LOW AC	PARALLEL R421 WITH A 15k,3 WATT OR R421 TO 3.9k 5W
PHILIPS	N/A	19L1	SET GOES INTO SHUTDOWN WHEN COLD--LATER ATTEMPTS TO TURN- ON MAY BE SUCCESSFUL.	CHANGE Q422 TO P/N(483513047056)-Z422 (483513037086) ADD 330pF(483512247058)PARALLEL C506 IF C505 4700pF
PHILIPS	N/A	19L1	ROLLING OR NO VERTICAL SYNC	CHECK/REPLACE C2515
PHILIPS	N/A	19L1	NUISANCE SHUTDOWN	CHNG. R520 TO 1.8k R523 TO 130k
PHILIPS	N/A	19L1	DARK PICTURE OR NO PICTURE	CHECK/REPLACE C2 FOR SHORT ON CRT BOARD
PHILIPS	N/A	19L1	SLUGGISH TRANSMITTER RESPONSE	REPLACE MICROPROCESSOR WITH UPDATED VERSION
PHILIPS	N/A	19L1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19L1	NO PIX - WHEN G1 WAS INCREASED,THEN THERE WAS NO VERT. SWEEP.	CHECK/REPLACE FLYBACK IF PINS #2 & #3 ARE OPEN.
PHILIPS	N/A	19L1	FLYBACK CHATTERS - NO SOUND OR PIX - ALL SCAN SUPPLIES LOW	CHECK/REPLACE Q421,Q422 OR Z422 FOR LEAKAGE OR BREAKING DOWN UNDER LOAD
PHILIPS	N/A	19L1	SET GOES INTO SHUTDOWN ON CHANNEL OR SCENE CHANGES	CHANGE R520 TO 1.8k AND R523 TO 130k - READJUST THE HORZ. FREQ. AFTER MODIFICATION
PHILIPS	N/A	19L1	BLACK BAR IN PIX AND VERTICAL STRETCHED	CHECK/REPLACE IC450 (REGULATOR)
PHILIPS	N/A	19L1	HORZ. TEARING -- SET TRIES TO FOLDOVER IN THE CENTER	CHECK/REPLACE R502 (47k)
PHILIPS	N/A	19L1	HIGH VOLUME WITH NO CONTROL--SHORT VERT SWEEP	CHECK/REPLACE IC450 (12V REGULATOR)
PHILIPS	N/A	19L1	DEAD SET -RELAY CHATTERS DUE TO OVER-VOLTAGE SHUTDOWN	CHECK/REPLACE IC430
PHILIPS	N/A	19L1	ERRATIC CUSTOMER ADJUSTMENTS	CHECK/REPLACE IC350
PHILIPS	N/A	19L1	DEAD SET-HORZ DRIVE TO BASE OF Q501 BUT NOTHING ON COLLECT.	CHECK R502 FOR OPEN (47K)
PHILIPS	N/A	19L1	STAND-BY AND RESET VOLTAGES MISSING	CHECK/REPLACE Q531 (OVER-VOLTAGE SHUT-DOWN LATCH)
PHILIPS	N/A	19L1	STANDBY AND RESET VOLTAGES ARE MISSING	CHECK/REPLACE Q531 FOR E-C LEAKAGE
PHILIPS	N/A	19L1	TV COMES ON BY ITSELF-WON'T TURN OFF-NO RECEPTION OR DISPLAY.	CHECK/REPLACE Z410 FOR LEAKY (SHOULD BE 4.9V)
PHILIPS	N/A	19L1	NO COLOR WHEN SET IS COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19L1	DEAD SET	CHECK/REPLACE IC401 ANF F401
PHILIPS	N/A	19L1	NO AUDIO	CHECK/REPLACE R231 (15 1/4w)
PHILIPS	N/A	19L1	RELAY CLICKS - SET HAS HIGH VOLTAGE BUT NO SOUND OR VERTICAL SWEEP	CHECK/REPLACE IC450 FOR OPEN
PHILIPS	N/A	19L1	DEAD SET BUT DOES TICK A FEW SECONDS WHEN PLUGGED IN	CHECK D413 FOR SHORTS
PHILIPS	N/A	19L1	BLACK VERTICAL BAR ON SCREEN	CHECK/REPLACE R512 FOR OPEN
PHILIPS	N/A	19L1	NUISANCE BLOWN FUSES FOR NO APPARENT REASON	INCREASE FUSE VALUE BY .5 AMPS TO A 2AMP
PHILIPS	N/A	19L1	FLAGGING ON VCR	CHNG.R523 TO 82k
PHILIPS	N/A	19L1	NO PICTURE,VOLUME IS AT MAXIMUM AND RELAY CHATTERS	CHECK/REPLACE IC430
PHILIPS	N/A	19L1	CANNOT CHANGE TINT,COLOR,BRIGHTNESS OR PICTURE CONTROLS	CHECK/REPLACE IC350
PHILIPS	N/A	19L1	LOSS OF THE HOTEL-MOTEL MODE	REPLACE IC350
PHILIPS	N/A	19L1	NO HORZ. OR VERT. SYNC.	CHECK/REPLACE IC200
PHILIPS	N/A	19L1	RELAY BUZZES - OTHERWISE SET IS DEAD	CHECK/REPLACE D413 AND R410
PHILIPS	N/A	19L1	NO SOUND BUT PICTURE IS FINE	CHECK/REPLACE R231 FOR OPEN
PHILIPS	N/A	19L1	NARROW HORIZONTAL SWEEP,VERTICAL FOLDOVER AND VOLUME FLUCUATES UP AND DOWN.	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	19L1	OSD GRAPHICS ARE DISTORTED OR HAVE EXTRA DOTS ON SCREEN	REPLACE IC350 (483520987257)
PHILIPS	N/A	19L1	BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO	CHECK Q630,Q631,Q632
PHILIPS	N/A	19L1	SLOW COLOR LOCK IN AFTER A CHANNEL IS CHANGED	USE A SELECTED CRYSTAL WITH BLUE MARKINGS ON CASE
PHILIPS	N/A	19L1	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19L4	TV COMES ON BY ITSELF-WON'T TURN OFF-NO RECEPTION OR DISPLAY.	CHECK/REPLACE Z410 FOR LEAKY (SHOULD BE 4.9V)
PHILIPS	N/A	19L4	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19L4	HIGH PITCHED SOUND FROM FLYBACK	CHECK R465 AND R501--EITHER ONE MAY HAVE INCREASED.
PHILIPS	N/A	19L4	NARROW HORIZONTAL SWEEP,VERTICAL FOLDOVER AND VOLUME FLUCUATES UP AND DOWN.	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	19L4	LOSS OF THE HOTEL-MOTEL MODE	REPLACE IC350
PHILIPS	N/A	19L4	STANDBY AND RESET VOLTAGES ARE MISSING	CHECK/REPLACE Q531 FOR E-C LEAKAGE
PHILIPS	N/A	19L4	NUISANCE SHUTDOWN	CHNG. R520 TO 1.8k R523 TO 130k
PHILIPS	N/A	19L4	MAY NOT START AT LOW AC	PARALLEL R421 WITH A 15k,3 WATT OR R421 TO 3.9k 5W
PHILIPS	N/A	19L4	BRIGHT SCREEN WITH RETRACE LINES - G1 WILL NOT CORRECT	CHECK/REPLACE R460,D460 AND C461
PHILIPS	N/A	19L4	SLUGGISH TRANSMITTER RESPONSE	REPLACE MICROPROCESSOR WITH UPDATED VERSION
PHILIPS	N/A	19L4	CANNOT CHANGE TINT,COLOR,BRIGHTNESS OR PICTURE CONTROLS	CHECK/REPLACE IC350
PHILIPS	N/A	19L4	NO SOUND BUT PICTURE IS FINE	CHECK/REPLACE R231 FOR OPEN
PHILIPS	N/A	19L4	SET TURNS ON BY ITSELF OR CANNOT BE TURNED OFF	CHECK/REPLACE D414 FOR LEAKAGE USE 483513037048)
PHILIPS	N/A	19L4	RELAY CLICKS - SET HAS HIGH VOLTAGE BUT NO SOUND OR VERTICAL SWEEP	CHECK/REPLACE IC450 FOR OPEN
PHILIPS	N/A	19L4	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19L4	OSD GRAPHICS ARE DISTORTED OR HAVE EXTRA DOTS ON SCREEN	REPLACE IC350 (483520987257)
PHILIPS	N/A	19L4	BLACK VERTICAL BAR ON SCREEN	CHECK/REPLACE R512 FOR OPEN
PHILIPS	N/A	19L4	HIGH VOLUME WITH NO CONTROL--SHORT VERT SWEEP	CHECK/REPLACE IC450 (12V REGULATOR)
PHILIPS	N/A	19L4	FLAGGING ON VCR	CHNG.R523 TO 82k
PHILIPS	N/A	19L4	SET GOES INTO SHUTDOWN ON CHANNEL OR SCENE CHANGES	CHANGE R520 TO 1.8k AND R523 TO 130k - READJUST THE HORZ. FREQ. AFTER MODIFICATION
PHILIPS	N/A	19L4	FLYBACK CHATTERS - NO SOUND OR PIX - ALL SCAN SUPPLIES LOW	CHECK/REPLACE Q421,Q422 OR Z422 FOR LEAKAGE OR BREAKING DOWN UNDER LOAD
PHILIPS	N/A	19L4	NO AUDIO	CHECK/REPLACE R231 (15 1/4w)
PHILIPS	N/A	19L4	HORZ. TEARING -- SET TRIES TO FOLDOVER IN THE CENTER	CHECK/REPLACE R502 (47k)
PHILIPS	N/A	19L4	SET GOES INTO SHUTDOWN WHEN COLD--LATER ATTEMPTS TO TURN- ON MAY BE SUCCESSFUL.	CHANGE Q422 TO P/N(483513047056)-Z422 (483513037086) ADD 330pF(483512247058)PARALLEL C506 IF C505 4700pF
PHILIPS	N/A	19L4	DEAD SET - APPEARS TO HAVE NO START-UP VOLTAGE	CHECK/REPLACE Q422 AND Q330
PHILIPS	N/A	19L4	NO COLOR WHEN SET IS COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19L4	DEAD SET BUT DOES TICK A FEW SECONDS WHEN PLUGGED IN	CHECK D413 FOR SHORTS
PHILIPS	N/A	19L4	ROLLING OR NO VERTICAL SYNC	CHECK/REPLACE C2515
PHILIPS	N/A	19L4	BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO	CHECK Q630,Q631,Q632
PHILIPS	N/A	19L4	NO PICTURE,VOLUME IS AT MAXIMUM AND RELAY CHATTERS	CHECK/REPLACE IC430
PHILIPS	N/A	19L4	NO PIX - WHEN G1 WAS INCREASED,THEN THERE WAS NO VERT. SWEEP.	CHECK/REPLACE FLYBACK IF PINS #2 & #3 ARE OPEN.
PHILIPS	N/A	19L4	ERRATIC CUSTOMER ADJUSTMENTS	CHECK/REPLACE IC350
PHILIPS	N/A	19L4	DEAD SET-HORZ DRIVE TO BASE OF Q501 BUT NOTHING ON COLLECT.	CHECK R502 FOR OPEN (47K)
PHILIPS	N/A	19L4	BLACK BAR IN PIX AND VERTICAL STRETCHED	CHECK/REPLACE IC450 (REGULATOR)
PHILIPS	N/A	19L4	NUISANCE BLOWN FUSES FOR NO APPARENT REASON	INCREASE FUSE VALUE BY .5 AMPS TO A 2AMP
PHILIPS	N/A	19L4	DEAD SET -RELAY CHATTERS DUE TO OVER-VOLTAGE SHUTDOWN	CHECK/REPLACE IC430
PHILIPS	N/A	19L4	DEAD SET	CHECK/REPLACE IC401 ANF F401
PHILIPS	N/A	19L4	DARK PICTURE OR NO PICTURE	CHECK/REPLACE C2 FOR SHORT ON CRT BOARD
PHILIPS	N/A	19L4	STAND-BY AND RESET VOLTAGES MISSING	CHECK/REPLACE Q531 (OVER-VOLTAGE SHUT-DOWN LATCH)
PHILIPS	N/A	19L4	NO HORZ. OR VERT. SYNC.	CHECK/REPLACE IC200
PHILIPS	N/A	19L4	RELAY BUZZES - OTHERWISE SET IS DEAD	CHECK/REPLACE D413 AND R410
PHILIPS	N/A	19N1	OSD ROLLS UP THROUGH THE PIX AND CHANNEL NUMBER LAGS CHANNEL CHANGE BY 2 SECONDS	CHECK/REPLACE D750 (MAY CHECK GOOD)
PHILIPS	N/A	19N1	INTERMITTENTLY GOES OFF	CHECK/RESOLDER CONNECTIONS ON T501
PHILIPS	N/A	19N1	POOR AFT LOCK - PICTURE SEARCHES	CHECK/REPLACE Q407
PHILIPS	N/A	19N1	SET SHUTS OFF AT RANDOM	CHECK/REPLACE IC350
PHILIPS	N/A	19N1	OSD ROLLS	CHECK/REPLACE D750 AND Q380
PHILIPS	N/A	19N1	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19N1	IC401 FAILURE IN THE POWER SUPPLY - OR NO REGULATION	CHECK/REPLACE IC401 AND Q403
PHILIPS	N/A	19N1	DEAD SET OR MAY INTERMITTENTLY START	CHECK FOR PRESENCE OF PHILIPS MICROPROCESSOR - IF USED THEN REMOVE C320 AND C321
PHILIPS	N/A	19N1	NO ON-SCREEN DISPLAY	CHECK/REPLACE Q380 FOR SHORT OR LEAKAGE
PHILIPS	N/A	19N1	NO OSD	CHECK/REPLACE D750 (WHICH IS NOT SHOWN IN THE SERVICE MANUAL)
PHILIPS	N/A	19N1	DEAD SET	CHECK/REPLACE IC401 ANF F401
PHILIPS	N/A	19N1	NO AUDIO OR DISTORTED AUDIO	CHECK C230 - IT SHOULD BE A 100nF/100V (483512147036)
PHILIPS	N/A	19N1	NO COLOR WHEN SET IS COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19N1	NUISANCE BLOWN FUSES FOR NO APPARENT REASON	INCREASE FUSE VALUE BY .5 AMPS TO A 2AMP
PHILIPS	N/A	19N1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C411 (100uF @ 200v)
PHILIPS	N/A	19N1	MICROPROCESSOR LOCKS UP AND GRAPHICS APPEAR TO BE WASHED OUT.	CHECK/REPLACE IC350 (483520987549)
PHILIPS	N/A	19N1	NO REMOTE CONTROL OPERATION - SET WORKS MANUALLY	CHECK/REPLACE IC350 FOR CORRECT VERSION - IF SET HAS A 4MHZ XTAL USE (483520987551),IF 6MHZ USE (483520987549)
PHILIPS	N/A	19N1	SLOW COLOR LOCK IN AFTER A CHANNEL IS CHANGED	USE A SELECTED CRYSTAL WITH BLUE MARKINGS ON CASE
PHILIPS	N/A	19N1	FUSE BLOWS FOR NO APPARENT REASON	CHECK JUMPER B67 TO SEE IF ITS TOUCHING C410
PHILIPS	N/A	19N1	NO CONTROL OF THE BRIGHTNESS	CHECK/REPLACE C343 FOR SHORT
PHILIPS	N/A	19N1	MORE THAN ONE 'ON' COMMAND REQUIRED TO START SET--MAY BE ENCOUNTERED AFTER REPL. OF H.O.T OR IFT	CHECK R405 AND/OR C410 FOR OPEN
PHILIPS	N/A	19N1	ERRATIC OSD WHEN SET IS HOT	CHECK/REPLACE IC350
PHILIPS	N/A	19N1	MICROPROCESSOR LOCKS UP AND GRAPHICS APPEAR TO BE WASHED OUT.	CHECK/REPLACE IC350
PHILIPS	N/A	19N1	INTERMITTENT SHUTDOWN, ESPECIALLY WHEN AC IS ABOVE 120v.	CHECK/REPLACE R410 (150k 1/2watt)
PHILIPS	N/A	19N1	DEAD SET - MAY TAKE MORE THAN ONE TRY TO TURN SET ON	CHECK/REPLACE R405
PHILIPS	N/A	19N1	SET SHUTS OFF	CHECK/REPLACE Q310 FOR INTERMITTENT
PHILIPS	N/A	19N1	NO CONTROL OF BRIGHTNESS	CHECK/REPLACE C343
PHILIPS	N/A	19N5	NARROW RASTER - MAY ALSO HAVE FAINT JAILBARS	CHECK/REPLACE C508 WITH 10nF @ 50v (P/N# 483512147461)
PHILIPS	N/A	19N5	NO HORZ. SYNC. OR SET HAS A BLUE SCREEN	CHECK PIN #5 OF IC530 IS HIGH AND ALL INPUTS ARE NORMAL, THEN REPLACE IC530
PHILIPS	N/A	19P1	SET TURNS ON THEN MICROPROCESSOR LOCKS UP - WILL NOT TURN BACK OFF - SNOWY RASTER LOCKED ON ONE CHANNEL	CHECK/REPLACE Q337
PHILIPS	N/A	19P1	NOISY OR SQUEALING SOUND COMING FROM SWITCHING TRANSFORMER	CHECK/REPLACE R410 OR R421 FOR OPEN
PHILIPS	N/A	19P1	INTERMITTENT SHUTDOWN	CHECK/REPLACE R663
PHILIPS	N/A	19P1	DEAD SET WITH NO STANDBY POWER	CHECK/REPLACE Q420 AND R424
PHILIPS	N/A	19P1	SET SHUTS OFF AT RANDOM	CHECK/REPLACE IC350
PHILIPS	N/A	19P1	DEAD SET AND RESET PIN #33 STAYS AT 1.5 VOLTS	CHECK/REPLACE IC351
PHILIPS	N/A	19P1	DEAD SET	CHECK/REPLACE Q420,D430,R427,R428 AND R424.
PHILIPS	N/A	19P1	REMOTE 'OFF' BUTTON MUST BE PRESSED TWICE TO TURN SET OFF.	CHECK/REPLACE IR90 INFRARED RECEIVER
PHILIPS	N/A	19P1	POWER SUPPLY GOES INTO SHUTDOWN AT POWER ON OR CHANNEL CHANGE OR SCENE CHANGES.	CHECK/REPLACE R430 (110K) FOR CHANGE IN VALUE.
PHILIPS	N/A	19P1	SET WILL COME ON ONCE AND THEN WON'T SHUT OFF OR IT WILL SHUT OFF AND NOT COME BACK ON.	CHECK/REPLACE IC350 (MICRO-PROCESSOR)
PHILIPS	N/A	19P1	ROLLING/FLAGING/HORZ. TEARING AT TOP OF PICTURE	REPLACE IC200 WITH NEW VERSION (TDA4505B) (USE 483531057062)
PHILIPS	N/A	19P1	BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO	CHECK Q630,Q631,Q632
PHILIPS	N/A	19P1	RADIO INTERFERENCE,DOTS,SWIRLS OR HERRINGBONE SEEN ON PIP VERSIONS.	CHECK/REPLACE PIP MODULE (ISOLATE BY UNPLUGGING J602)
PHILIPS	N/A	19P1	NO VERTICAL SWEEP	CHECK/REPLACE R445 FOR OPEN
PHILIPS	N/A	19P1	INTERMITTENT OPERATION - LEDS WOULD LIGHT FOR A SECOND	CHECK/RESOLDER CONECTIONS ON C451 (NEAR FLYBACK)
PHILIPS	N/A	19P1	SET SHUTS DOWN DURING SCENE CHANGES OR CHANGING CHANNELS	CHECK/REPLACE D661,R663 AND Q661
PHILIPS	N/A	19P1	INTERMITTENT DEAD SET	CHECK/RESOLDER C431
PHILIPS	N/A	19P1	SET SHUTS DOWN BUT WITH SCREEN CTRL. ALL THE WAY DOWN, THE SET WILL REMAIN TO RUN WITH WHITE SCREEN WITH RETRACE.	CHECK/REPLACE R11 (100 OHM) ON THE CRT BOARD -- (200 VOLT SOURCE)
PHILIPS	N/A	19P1	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	19P1	SET IS SHUTTING DOWN	CHECK/REPLACE R11 (CRT BOARD) FOR OPEN
PHILIPS	N/A	19P1	ERRATIC OSD WHEN SET IS HOT	CHECK/REPLACE IC350
PHILIPS	N/A	19P1	NO COLOR AND VOLTAGES ON IC600 PINS#12,13,14 ARE LOW	CHECK/REPLACE IC600
PHILIPS	N/A	19P1	BRIGHT SCREEN WITH RETRACE LINES	CHECK/REPLACE R663 FOR OPEN
PHILIPS	N/A	19P1	JAIL BARS ON THE LEFT SIDE OF THE SCREEN	CHECK/REPLACE L502 WITH NEW TYPE (483515757336)
PHILIPS	N/A	19P5	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1m?(P/N# 483511057204)
PHILIPS	N/A	19P5	VERTICAL JITTER OR BOUNCE ON SOME CBALE CHANNELS	CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038)
PHILIPS	N/A	19P5	TV WON'T SHUT OFF	CHECK/REPLACE Q400 (483513047072), Q402 (483513047059), D420 (483513037048),R431 (47 ), R432 (1K ), R437 (4.7 )
PHILIPS	N/A	19P5	VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL	CHECK/REPLACE R222 OPEN (12k? (P/N# 483511657397)
PHILIPS	N/A	19P5	VIDEO SMEARS ON BRIGHT OBJECTS	ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND
PHILIPS	N/A	19P5	CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU	REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25'
PHILIPS	N/A	19P5	ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM	CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES
PHILIPS	N/A	19P6	VERTICAL JITTER OR BOUNCE ON SOME CBALE CHANNELS	CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038)
PHILIPS	N/A	19P6	TV WON'T SHUT OFF	CHECK/REPLACE Q400 (483513047072), Q402 (483513047059), D420 (483513037048),R431 (47 ), R432 (1K ), R437 (4.7 )
PHILIPS	N/A	19P6	CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU	REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25'
PHILIPS	N/A	19P6	A SLIGHT VERTICAL DRIVE LINE MAY BE SEEN	INSTALL JUMPER AT B1 (GRID D2)
PHILIPS	N/A	19P6	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1m?(P/N# 483511057204)
PHILIPS	N/A	19P6	DEAD SET	CHECK FOR OPEN TRACE IN GRID 'H6' - ADD INSULATED WIRE FROM AC NUETRAL TO POINT MARKED PIN # 1 OF L400
PHILIPS	N/A	19P6	ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM	CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES
PHILIPS	N/A	19P6	VIDEO SMEARS ON BRIGHT OBJECTS	ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND
PHILIPS	N/A	19P6	VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL	CHECK/REPLACE R222 OPEN (12k? (P/N# 483511657397)
PHILIPS	N/A	19S1	DEAD SET - F401 BLOWN AND AFTER REPLACING R432 BURNS	CHECK/REPLACE IC430 AND R432 (1K )
PHILIPS	N/A	19S1	NO TUNING ON CHANNELS 15-20 - ALL OTHERS OK	CHECK/REPLACE TUNER (483521047006)
PHILIPS	N/A	19S1	OSD SHIFTED TOO FAR TO THE RIGHT	CHECK/REPLACE IC351
PHILIPS	N/A	19S1	SLUGGISH KEYBOARD RESPONSE	CHECK AND RE-DRESS THE KEYBOARD CABLE AWAY FROM FLYBACK
PHILIPS	N/A	19S1	WEAK VIDEO - WASHED VIDEO	CHECK/REPLACE Q210
PHILIPS	N/A	19S1	DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ******	CHECK/REPLACE R407 (483511687002) AND T502 (483514247015)
PHILIPS	N/A	19S1	OPERATION OF SET CAUSES INTERFERENCE ON NEAR BY AM RADIOS	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	19S1	FAILURE OF IC430	CHECK/REPLACE IC430 AND Q400 FOR OPEN - ALSO CHECK THE SOLDER CONNECTIONS ON Q400
PHILIPS	N/A	19S1	NOISY BACKGROUND OR OVER PEAKED VIDEO	CHANGE R609 TO A 2.7k
PHILIPS	N/A	19S1	BRIGHT PICTURE WITH RETRACE LINES	CHECK/REPLACE Z410 AND Q410
PHILIPS	N/A	19S1	TEARING OR FLUTTERING LINES IN THE PICTURE AT LOW BRIGHTNESS	ADD A 6.8v ZENER ACROSS R676 WITH CATHODE TO 9v SOURCE - P/N# 483513037487
PHILIPS	N/A	19S1	LOSS OF MEMORY DUE TO GLITCHES IN THE RESET CIRCUIT	CHANGE R305 > 10 ohm, R416 > 2.2k, R417 > 10 ohm, R492 >> REMOVE, C411 > 22uF, D414 > 3.9v ZENER, Z410 > 5.6v ZENER
PHILIPS	N/A	19S1	OSD IS OFF CENTER - IT COULD BE SO FAR OFF CENTER THAT IT CAN'T BE SEEN	MOMENTARILY SHORT PINS 12 & 13 TO ENTER TEST MODE - PRESS RESET BUTTON TO GET TO REG.#10 - USE (+/-) TO CENTER
PHILIPS	N/A	19S1	NO REMOTE CONTROL RESPONSE	CHECK/REPLACE IR RECEIVER (483521027003)
PHILIPS	N/A	19S1	R407 FAILS FOR NO APPARENT REASON AND Q403 MAY ALSO BE BAD	CHECK/REPLACE R407 (ONLY P/N 483511687002) - ADD 6.8k IN PARALLEL W/Z406 - CHNG. R502 TO 130 ohm-REPL. Z411 W/2.7k
PHILIPS	N/A	19S1	NO SOUND BUT PIX IS NORMAL	CHECK/REPLACE IC230
PHILIPS	N/A	19S1	RED SMEAR - LOOKS LIKE A BAD CRT *** STEREO VERSIONS ONLY ***	CHANGE C506 TO (2508850006)
PHILIPS	N/A	19S1	TOTALLY DEAD	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	19S1	REPEATED OR EARLY FAILURE OF IC430	CHECK/REPLACE Q400
PHILIPS	N/A	19S1	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE R435 (130k ) FOR OPEN
PHILIPS	N/A	19S1	TEARING IN THE PICTURE AT VARIOUS BRIGHTNESS LEVELS	ADD 22k FROM PIN#40 OF IC265 TO GRD.,CHANGE C617 > 47uF, BRIGHTNESS REG.#11 MAY NEED TO BE RESET FOR BEST PERFORM.
PHILIPS	N/A	19S1	RED SMEAR - LOOKS LIKE A BAD CRT *** MONO VERSIONS ONLY ***	CHANGE C505 TO (483512147242) AND C506 TO (483512257004)
PHILIPS	N/A	19S1	NO AUDIO OR INTERMITTENT AUDIO	CHECK/REPLACE Y220 OR COLD SOLDER CONNECTIONS
PHILIPS	N/A	19S1	SHADING ON THE RIGHT SIDE OF THE PICTURE	CHECK/REPLACE C399 (P/N# 483512217002) - A FEW SETS WERE SENT OUT WITH A 1k RESISTOR IN PLACE OF THE CAPACITOR
PHILIPS	N/A	19S1	DEAD SET, POSSIBLY AFTER POWER SURGE	CHECK/REPLACE R403 (P/N# 483511247007),D401,D402,D403,D404 (P/N# FOR ALL 483513037059),R407 (P/N# 483511687002)
PHILIPS	N/A	19S1	CANNOT TURN SET OFF	CHECK/REPLACE R438 (680k) FOR OPEN
PHILIPS	N/A	19S1	SHORT VERTICAL SWEEP - ABOUT 2'	CHECK/REPLACE R565 FOR OPEN
PHILIPS	N/A	19S1	REPEATED SEARCHING IN THE CABLE MODE	CHANGE R241 TO A 680k (P/N 483511067143)
PHILIPS	N/A	19S1	NO HORZ. SWEEP - ONE VERTICAL WHITE LINE DOWN SCREEN	CHECK/REPLACE L507 FOR OPEN (P/N# 3620280021)
PHILIPS	N/A	19S1	DARK PICTURE OR NO PICTURE	CHECK/REPLACE C2 FOR SHORT ON CRT BOARD
PHILIPS	N/A	19S1	BLACK AND WHITE PIP MODULE FAILS TO OPERATE	CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048)
PHILIPS	N/A	19S1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19S1	HUM OR AUDIO BUZZ OR DISTORTED AUDIO	CHECK TO SEE IF C464 IS A 100uF AND C465 IS A 1000pF ( THESE HAVE BEEN INTER-CHANGED ON SOME CHASSIS )
PHILIPS	N/A	19S1	DEAD SET	CHECK/REPLACE R407,Q403 AND T502 FOR OPEN WINDING
PHILIPS	N/A	19S1	NO PICTURE OR VERY DARK PICTURE - NO OSD	CHECK FOR CARBON PATH BETWEEN PINS #7 & #8 ON FLYBACK
PHILIPS	N/A	19S4	RED SMEAR - LOOKS LIKE A BAD CRT *** STEREO VERSIONS ONLY ***	CHANGE C506 TO (2508850006)
PHILIPS	N/A	19S4	DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ******	CHECK/REPLACE R407 (483511687002) AND T502 (483514247015)
PHILIPS	N/A	19S4	RED SMEAR - LOOKS LIKE A BAD CRT *** MONO VERSIONS ONLY ***	CHANGE C505 TO (483512147242) AND C506 TO (483512257004)
PHILIPS	N/A	19S4	NO HORZ. SWEEP - ONE VERTICAL WHITE LINE DOWN SCREEN	CHECK/REPLACE L507 FOR OPEN (P/N# 3620280021)
PHILIPS	N/A	19S4	OSD IS OFF CENTER - IT COULD BE SO FAR OFF CENTER THAT IT CAN'T BE SEEN	MOMENTARILY SHORT PINS 12 & 13 TO ENTER TEST MODE - PRESS RESET BUTTON TO GET TO REG.#10 - USE (+/-) TO CENTER
PHILIPS	N/A	19S4	CANNOT TURN SET OFF	CHECK/REPLACE R438 (680k) FOR OPEN
PHILIPS	N/A	19S4	DEAD SET - F401 BLOWN AND AFTER REPLACING R432 BURNS	CHECK/REPLACE IC430 AND R432 (1K )
PHILIPS	N/A	19S4	REPEATED OR EARLY FAILURE OF IC430	CHECK/REPLACE Q400
PHILIPS	N/A	19S4	NO SOUND BUT PIX IS NORMAL	CHECK/REPLACE IC230
PHILIPS	N/A	19S4	R407 FAILS FOR NO APPARENT REASON AND Q403 MAY ALSO BE BAD	CHECK/REPLACE R407 (ONLY P/N 483511687002) - ADD 6.8k IN PARALLEL W/Z406 - CHNG. R502 TO 130 ohm-REPL. Z411 W/2.7k
PHILIPS	N/A	19S4	BRIGHT PICTURE WITH RETRACE LINES	CHECK/REPLACE Z410 AND Q410
PHILIPS	N/A	19S4	NO PICTURE OR VERY DARK PICTURE - NO OSD	CHECK FOR CARBON PATH BETWEEN PINS #7 & #8 ON FLYBACK
PHILIPS	N/A	19S4	TOTALLY DEAD	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	19S4	WEAK VIDEO - WASHED VIDEO	CHECK/REPLACE Q210
PHILIPS	N/A	19S4	NO TUNING ON CHANNELS 15-20 - ALL OTHERS OK	CHECK/REPLACE TUNER (483521047006)
PHILIPS	N/A	19S4	OSD SHIFTED TOO FAR TO THE RIGHT	CHECK/REPLACE IC351
PHILIPS	N/A	19S4	LOSS OF MEMORY DUE TO GLITCHES IN THE RESET CIRCUIT	CHANGE R305 > 10 ohm, R416 > 2.2k, R417 > 10 ohm, R492 >> REMOVE, C411 > 22uF, D414 > 3.9v ZENER, Z410 > 5.6v ZENER
PHILIPS	N/A	19S4	OPERATION OF SET CAUSES INTERFERENCE ON NEAR BY AM RADIOS	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	19S4	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE R435 (130k ) FOR OPEN
PHILIPS	N/A	19S4	BLACK AND WHITE PIP MODULE FAILS TO OPERATE	CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048)
PHILIPS	N/A	19S4	TEARING OR FLUTTERING LINES IN THE PICTURE AT LOW BRIGHTNESS	ADD A 6.8v ZENER ACROSS R676 WITH CATHODE TO 9v SOURCE - P/N# 483513037487
PHILIPS	N/A	19S4	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19S4	TEARING IN THE PICTURE AT VARIOUS BRIGHTNESS LEVELS	ADD 22k FROM PIN#40 OF IC265 TO GRD.,CHANGE C617 > 47uF, BRIGHTNESS REG.#11 MAY NEED TO BE RESET FOR BEST PERFORM.
PHILIPS	N/A	19S4	NO REMOTE CONTROL RESPONSE	CHECK/REPLACE IR RECEIVER (483521027003)
PHILIPS	N/A	19S4	SHORT VERTICAL SWEEP - ABOUT 2'	CHECK/REPLACE R565 FOR OPEN
PHILIPS	N/A	19S4	DEAD SET, POSSIBLY AFTER POWER SURGE	CHECK/REPLACE R403 (P/N# 483511247007),D401,D402,D403,D404 (P/N# FOR ALL 483513037059),R407 (P/N# 483511687002)
PHILIPS	N/A	19S4	FAILURE OF IC430	CHECK/REPLACE IC430 AND Q400 FOR OPEN - ALSO CHECK THE SOLDER CONNECTIONS ON Q400
PHILIPS	N/A	19S4	DEAD SET	CHECK/REPLACE R407,Q403 AND T502 FOR OPEN WINDING
PHILIPS	N/A	19S4	REPEATED SEARCHING IN THE CABLE MODE	CHANGE R241 TO A 680k (P/N 483511067143)
PHILIPS	N/A	19U6	DEAD SET - NO HIGH VOLTAGE	CHECK/REPLACE Q500 (P/N# 483513047073)
PHILIPS	N/A	19X6	VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL	CHECK/REPLACE R222 OPEN (12k? (P/N# 483511657397)
PHILIPS	N/A	19X6	VERTICAL HEIGHT WON'T ADJUST CORRECTLY, ESPECIALLY IF UNIT IS HOT	CHECK/REPLACE R559 WITH 910?1/8w (P/N# 483511067238)
PHILIPS	N/A	19X6	INTERMITTENT LOSS OF HORZ. SYNC	CHECK/REPLACE Y620 (P/N# 483524277215)
PHILIPS	N/A	19X6	DEAD SET	CHECK/REPLACE Q502 (P/N# 483513067001) AND F401 (P/N# 483525397031)
PHILIPS	N/A	19Y1	NO AUDIO	CHECK/REPLACE Q95 (P/N# 483513047094), Q703 (483513047086), AND IC230 (P/N# 483520947005)
PHILIPS	N/A	19Y1	CLOSED CAPTION IS MISSING FROM THE MENU AND IS TURNED ON	CHECK/RESOLDER CONNECTIONS ON B70 AND B10
PHILIPS	N/A	19Y1	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	19Y1	HORIZONTAL OUTPUT FAILURE	CHECK/REPLACE C504 (483512147278)
PHILIPS	N/A	19Y1	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE Q402 (P/N# ECG382)
PHILIPS	N/A	19Y1	SHORT VERTICAL SWEEP OR FOLDOVER	CHECK/REPLACE Q560 (P/N# 483513047064) AND R552 (P/N# 483511657322)
PHILIPS	N/A	19Y1	DEAD SET	CHECK/REPLACE Z402 (P/N# 483513037003), Z406 (483513037121)
PHILIPS	N/A	19Y1	SET WILL NOT TURN ON/OFF	CHECK IC410 (P/N# 483520947056), Q400 (483513047072), R438 (P/N# 483511657518), R432 (P/N# 483511657108)
PHILIPS	N/A	19Y1	NO VIDEO	CHECK PIP MODULE (483521977517),C301(483512497026),Q210 (483513047126),Q602 (483513047064), R243 (483511657322)
PHILIPS	N/A	19Y1	HORZ. IS OFF FREQUENCY	CHECK/REPLACE IC410 (P/N# 483520947056)
PHILIPS	N/A	19Y1	REMOTE WILL RESPOND TO REMOTES FOR OTHER PRODUCTS SUCH AS AUDIO,VCR, ETC.	CHECK/REPLACE IC350 WITH NEW TYPE (P/N# 483520988286)
PHILIPS	N/A	19Y1	OSD SHIFTED	CHECK/REPLACE IC346 (P/N# 483520988108)
PHILIPS	N/A	19Y1	NO CLOSED CAPTION	CHECK/REPLACE B10 AND B70
PHILIPS	N/A	19Y1	NO VIDEO OR POOR CONTRAST	CHECK/REPLACE C511 (P/N# 483512247224), R538 (483511657427)
PHILIPS	N/A	19Y1	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE Q502 (P/N# 483513047706) AND F401 (P/N# 483525397031)
PHILIPS	N/A	19Y1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19Y1	NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE	CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831)
PHILIPS	N/A	19Y1	NO VIDEO OR OSD	CHECK/REPLACE L630 (P/N# 483515757947),D508 (483513037048) L340 (P/N# 483515757141), R6 (483511657318 - CRT BOARD)
PHILIPS	N/A	19Y1	HORZ. RUNNING OFF FREQUENCY	CHECK/REPLACE Z530 (P/N# 483513037121)
PHILIPS	N/A	19Y1	NO SAP	ADD 270K (P/N# 483511067116) TO PIN #1 OF IC700 TO GRD.
PHILIPS	N/A	19Y1	CHANNEL NUMBERS CHANGE, BUT CHANNELS DON'T	CHECK/REPLACE PIP MODULE (P/N# 483521977517)
PHILIPS	N/A	19Y1	WON'T SHUT OFF - COMES ON WHEN PLUGGED IN	CHECK/REPLACE R438 (680k 1/2w)
PHILIPS	N/A	19Y1	TOTALLY DEAD	CHECK/REPLACE IC410 (STR30130)
PHILIPS	N/A	19Y1	TUNER WILL NOT TUNE ANY CHANNELS	CHECK/REPLACE R360 AND R361 (P/N# 483511657275)
PHILIPS	N/A	19Y1	VERTICAL OUTPUT FAILURE	CHECK/REPLACE IC550 AND C447 (P/N# 483512447013)
PHILIPS	N/A	19Y1	FLAGGING AT TOP - POOR HORZ. SYNC. - 200v LINE INCREASED	CHECK/REPLACE D406 (P/N# 483513037048)
PHILIPS	N/A	19Y1	AM RADIO INTERFERENCE	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	19Y1	POOR PICTURE	CHECK/REPLACE Z463 (P/N# 483513037121)
PHILIPS	N/A	19Y1	DISTORTED AUDIO OR NO AUDIO	CHECK/REPLACE L221 (P/N# 483515757113)
PHILIPS	N/A	19Y1	POOR CONTRAST AND BRIGHTNESS	CHECK/REPLACE Q510 (P/N# 483513047064), R468 (482211130483)
PHILIPS	N/A	19Y4	NO SAP	ADD 270K (P/N# 483511067116) TO PIN #1 OF IC700 TO GRD.
PHILIPS	N/A	19Y4	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	19Y4	NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE	CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831)
PHILIPS	N/A	19Y4	TOTALLY DEAD	CHECK/REPLACE IC410 (STR30130)
PHILIPS	N/A	19Y4	POOR CONTRAST AND BRIGHTNESS	CHECK/REPLACE Q510 (P/N# 483513047064), R468 (482211130483)
PHILIPS	N/A	19Y4	SET WILL NOT TURN ON/OFF	CHECK IC410 (P/N# 483520947056), Q400 (483513047072), R438 (P/N# 483511657518), R432 (P/N# 483511657108)
PHILIPS	N/A	19Y4	AM RADIO INTERFERENCE	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	19Y4	CLOSED CAPTION IS MISSING FROM THE MENU AND IS TURNED ON	CHECK/RESOLDER CONNECTIONS ON B70 AND B10
PHILIPS	N/A	19Y4	REMOTE WILL RESPOND TO REMOTES FOR OTHER PRODUCTS SUCH AS AUDIO,VCR, ETC.	CHECK/REPLACE IC350 WITH NEW TYPE (P/N# 483520988286)
PHILIPS	N/A	19Y4	HORZ. IS OFF FREQUENCY	CHECK/REPLACE IC410 (P/N# 483520947056)
PHILIPS	N/A	19Y4	TUNER WILL NOT TUNE ANY CHANNELS	CHECK/REPLACE R360 AND R361 (P/N# 483511657275)
PHILIPS	N/A	19Y4	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE Q402 (P/N# ECG382)
PHILIPS	N/A	19Y4	VERTICAL OUTPUT FAILURE	CHECK/REPLACE IC550 AND C447 (P/N# 483512447013)
PHILIPS	N/A	19Y4	HORIZONTAL OUTPUT FAILURE	CHECK/REPLACE C504 (483512147278)
PHILIPS	N/A	19Y4	OSD SHIFTED	CHECK/REPLACE IC346 (P/N# 483520988108)
PHILIPS	N/A	19Y4	NO CLOSED CAPTION	CHECK/REPLACE B10 AND B70
PHILIPS	N/A	19Y4	NO AUDIO	CHECK/REPLACE Q95 (P/N# 483513047094), Q703 (483513047086), AND IC230 (P/N# 483520947005)
PHILIPS	N/A	19Y4	HORZ. RUNNING OFF FREQUENCY	CHECK/REPLACE Z530 (P/N# 483513037121)
PHILIPS	N/A	19Y4	CHANNEL NUMBERS CHANGE, BUT CHANNELS DON'T	CHECK/REPLACE PIP MODULE (P/N# 483521977517)
PHILIPS	N/A	19Y4	DISTORTED AUDIO OR NO AUDIO	CHECK/REPLACE L221 (P/N# 483515757113)
PHILIPS	N/A	19Y4	FLAGGING AT TOP - POOR HORZ. SYNC. - 200v LINE INCREASED	CHECK/REPLACE D406 (P/N# 483513037048)
PHILIPS	N/A	19Y4	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE Q502 (P/N# 483513047706) AND F401 (P/N# 483525397031)
PHILIPS	N/A	19Y4	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	19Y4	DEAD SET	CHECK/REPLACE Z402 (P/N# 483513037003), Z406 (483513037121)
PHILIPS	N/A	19Y4	SHORT VERTICAL SWEEP OR FOLDOVER	CHECK/REPLACE Q560 (P/N# 483513047064) AND R552 (P/N# 483511657322)
PHILIPS	N/A	19Y4	NO VIDEO OR POOR CONTRAST	CHECK/REPLACE C511 (P/N# 483512247224), R538 (483511657427)
PHILIPS	N/A	19Y4	WON'T SHUT OFF - COMES ON WHEN PLUGGED IN	CHECK/REPLACE R438 (680k 1/2w)
PHILIPS	N/A	19Y4	NO VIDEO OR OSD	CHECK/REPLACE L630 (P/N# 483515757947),D508 (483513037048) L340 (P/N# 483515757141), R6 (483511657318 - CRT BOARD)
PHILIPS	N/A	19Y4	POOR PICTURE	CHECK/REPLACE Z463 (P/N# 483513037121)
PHILIPS	N/A	19Y4	NO VIDEO	CHECK PIP MODULE (483521977517),C301(483512497026),Q210 (483513047126),Q602 (483513047064), R243 (483511657322)
PHILIPS	N/A	20A5	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33k?
PHILIPS	N/A	20B1	NO PICTURE - NO SOUND AND NO RASTER	CHECK/REPLACE Q370
PHILIPS	N/A	20B1	SET WAS DEAD OUT-OF-BOX IN CUSTOMERS HOME	REPLACED OPEN R409
PHILIPS	N/A	20B1	DISTORTED AUDIO	CHECK/REPLACE R210 AND Q210
PHILIPS	N/A	20B1	DISTORTED AUDIO--OUTPUTS ARE OK	CHECK R210 -- ESPECIALLY IF OUTPUT XSTRS. WERE BAD
PHILIPS	N/A	20B1	NO COLOR	CHECK/REPLACE R516 OPEN
PHILIPS	N/A	20B1	AUDIO DISTORED AND HAS A BUZZING NOISE VOL.NOT W	REPLACED LEAKY VOLUME CONTROL AMP,Q370
PHILIPS	N/A	20B1	DEAD SET OR SHUTS DOWN	CHECK/REPLACE D530 OR Z530
PHILIPS	N/A	20B1	INTERMITTENT SHUTDOWN OR LOSS OF VERTICAL SWEEP	CHECK/REPLACE Z670 (P/N# 5301571270)
PHILIPS	N/A	20B1	DEAD SET TICKING SOUND	REPAIRED BROKEN SOLDER CONNECTION ON R335
PHILIPS	N/A	20B1	NO PICTURE,NO COLOR AND NO RASTER	CHECK/REPLACE Q516 (P/N# 6104359001)
PHILIPS	N/A	20B1	AUDIO OUTPUT FAILURES---REPL.C211 1uF C206 470pF	PARALLEL 470pF @ R202 R207 10 OHM R213&R214 130 OHM
PHILIPS	N/A	20B1	INT. SHUTDOWN OR LOSS OF VERT.SWEEP	Z670 LEAKY
PHILIPS	N/A	20B1	TUNER HUNTS ON CHANNEL CHANGES 4 TIMES - AFT PROBLEMS	CHECK R342 FOR INCREASE IN VALUE
PHILIPS	N/A	20B1	DEAD SET-MAY BE INTERMITTENT	CHECK CONNECTIONS ON R335
PHILIPS	N/A	20B1	SET WOULD NOT LOCK ON STATION	REPLACED Y301
PHILIPS	N/A	20B1	CHANNELS HIGHER THAN 7 CANNOT BE SELECTED	CHECK/REPLACE XT309
PHILIPS	N/A	20B1	INTERMITTENT SHUTDOWN	CHECK/REPLACE Q690 AND Z689
PHILIPS	N/A	20B1	PICTURE PULSATING FROM PIX TO SNOW	REPLACED R409
PHILIPS	N/A	20B1	VERT LINE ON LEFT SIDE OF SCREEN	INST. FERRITE BEAD ON EMITTER OF Q503
PHILIPS	N/A	20B1	POOR OR SNOWY RECEPTION	CHECK/REPLACE Q220 AND Q311 WITH (P/N# 610434004)
PHILIPS	N/A	20B1	VERTICAL FOLDOVER AFTER SET WARMS UP	CHECK/REPLACE D554 (P/N# 5302991001)
PHILIPS	N/A	20B1	TUNER SEARCHES - POOR AFT LOCK	CHECK/REPLACE IC250 - CHECK ALIGNMENT OF L243
PHILIPS	N/A	20B1	POP IN AUDIO AT TURN OFF	INST. COUPLING CAP.(0.1uF) PIN 6 OF AUDIO IC
PHILIPS	N/A	20B1	NO SOUND AND NO RASTER -IC250 LATCHES UP	REPLACE Q370 AND IC250
PHILIPS	N/A	20B1	SLOW VERTICAL ROLL - VETTICAL WON'T LOCK	CHECK/REPLACE R237
PHILIPS	N/A	20B1	EXCESSIVE B+ - 130V SOURCE TOO HIGH	CHECK/REPLACE R409
PHILIPS	N/A	20B1	VERY INTERMITTENT BURST OF SOUND WHILE SET IS TURNED OFF	CHECK/RESOLDER PRIMARY CONNECTIONS ON T471
PHILIPS	N/A	20B1	DEAD SET AND MAY BE INTERMITTENT	CHECK/REPLACE Y300
PHILIPS	N/A	20B1	PLAYS FOR 30 MINUTES AND THEN GOES DEAD	CHECK/RESOLDER CONNECTIONS ON T471
PHILIPS	N/A	20B1	DEAD SET	REPLACED IC400
PHILIPS	N/A	20B5	NO VIDEO - NO OSD - SOUND AND HIGH VOLTAGE BOTH OK	CHECK/REPLACE R511/R512 (220k? (453511657018), Q502 (483513047086)
PHILIPS	N/A	20B5	NO VERTICAL DEFLECTION	CHECK/REPLACE R516 (1?@ 1/2w)
PHILIPS	N/A	20B8	OSD IS NOT CENTERED - CLOSED CAPTION MAY RUN OFF THE SCREEN ENTER SERVICE MODE - ON SERVICE PAGE 'A', CURSOR UP TO	REG. 5A, ADJUST VALUE TO 0F - PRESS MENU TO SAVE - PRESS 9 THEN + TO EXIT AND SAVE - TURN ON SET TO CONFIRM CHANGES
PHILIPS	N/A	20B8	NO VERTICAL DEFLECTION	CHECK/REPLACE R420/R445 - REPLACE WITH NEW TYPE 1?@ 1/2w (P/N# 483511657109)
PHILIPS	N/A	20B8	DIM RASTER WITH FAINT COLORED BARS FROM TOP TO BOTTOM - NO MENU OR OSD GRAPHICS	CHECK/REPLACE R420,D409,C419 AND IC500
PHILIPS	N/A	20C5	NO SOUND AND POOR PICTURE - APPEARS TO HAVE ARCING IN THE PICTURE	CHECK/REPLACE D408 AND R408
PHILIPS	N/A	20C6	INTERMITTENT OR COMPLETE SHUTDOWN	CHECK/RESOLDER CONNECTIONS ON C550
PHILIPS	N/A	20C6	JAPANESE CHARACTERS AFTER REPLACING IC1200	CHECK/REPLACE IC1200 - MAKE SURE NUMBER ON IC IS MN1277B
PHILIPS	N/A	20C6	NO COLOR	CHECK/REPLACE IC50,Y50,IC10,R50,R435,C66,IC320,R56
PHILIPS	N/A	20C6	DEAD SET	CHECK C466 AND IC1200
PHILIPS	N/A	20C6	VOLUME AND CHANNELS CHANGE BY THEMSELVES	REPLACE 4.0MHz CRYSTAL
PHILIPS	N/A	20C6	Q501 OVERHEATS/SHORTS--APPEARS FLYBACK SHORTED	CHECK R503 (47 OHM) FOR OPEN OR HIGH RESISTANCE
PHILIPS	N/A	20C6	ARCING IN CRT OR IN VIDEO	CHECK/REPLACE T465
PHILIPS	N/A	20C6	DEAD SET	CHECK Q321 AND Z370
PHILIPS	N/A	20C6	DEAD SET-NO REGULATED B+	CHECK IC340 FOR SQR WAVE AT PIN #11-REPL. IF MISSING
PHILIPS	N/A	20C6	PICTURE OVER SCANS VERTICALLY AND HORIZONTALLY	CHECK Q464 FOR SHORTS -- ESPECIALLY IF SAFTEY CAP.
PHILIPS	N/A	20C6	HUM IN AUDIO	CHECK D170
PHILIPS	N/A	20C6	NO HIGH VOLTAGE	CHECK/REPLACE D461,Q464,Q463,T465,T460,IC320,R434,R435, R337,R464,R428,Q461,D462
PHILIPS	N/A	20C6	DEAD SET OR INTERMITTENT POWER	CHECK T400 CONNECTIONS
PHILIPS	N/A	20C6	MISSING ONE COLORS	CHECK/REPLACE IC50,Q11,Q31,Q51
PHILIPS	N/A	20C6	NO VIDEO	CHECK/REPLACE IC601,R434,R435,IC50,Q54,IC10,R56
PHILIPS	N/A	20C6	ON MODELS WITH 10 WATT AMP, A LOUD THUMP IS HEARD WHEN TURNING SET ON.	CHECK/REPLACE D170 AND CHANGE C163 FROM 330uF TO 1000uF
PHILIPS	N/A	20C6	DEAD SET-GRD. BASE OF Q402 AND SET COMES ON	CHECK/REPLACE IC403
PHILIPS	N/A	20C6	DISTORTED VERTICAL AT TOP AND BOTTOM	CHECK/REPLACE RESISTOR LOCATED ON THE ANODE SIDE OF D1 ON THE PINCUSHION MODULE.
PHILIPS	N/A	20C6	DEAD SET	CHECK/REPLACE Q400,D400,D401,D402,D403,Q401,R420,R408, IC403,D430,Z407,R402,R403,C411,Z436,R431
PHILIPS	N/A	20C6	DEAD SET	CHECK R434 AND D433
PHILIPS	N/A	20C6	RETRACE LINES IN PIX	CHECK/REPLACE C303,R56,IC50,IC320,IC300,Q11,Q31,Q51
PHILIPS	N/A	20C6	NO RASTER	DEFECTIVE CRT
PHILIPS	N/A	20C8	BRIGHT SCREEN W/RETRACE - SHORT VERT. - AUDIO IS NORMAL	CHECK R510 FOR OPEN
PHILIPS	N/A	20C8	NO VIDEO WITH RETRACE LINES	CHECK D500 FOR LEAKAGE (WILL CHECK GOOD)
PHILIPS	N/A	20C8	DARK PIX ON LEFT SIDE	CHECK C508
PHILIPS	N/A	20C8	DEAD SET AFTER INSTALLATION OF IC404	CHECK FOR PROPER ORIENTATION OF IC404 - SOME BOARDS WERE MARKED WRONG WITH RESPECT TO PIN#1 OF THE IC.
PHILIPS	N/A	20C8	DEAD SET - PIN#26 OF IC201 IS SHORTED TO GROUND.	CHECK/REPLACE Z436
PHILIPS	N/A	20C8	PIX BREAKS UP,BLOOMS,AND VERT SIZE DECREASES	CHECK Q406,Q407 AND Z436 FOR SHORTS
PHILIPS	N/A	20C8	DEAD SET	CHECK/REPLACE T500 (HORZ. DRIVER XFRM)
PHILIPS	N/A	20C8	DEAD SET--NO HORZ. DRIVE	CHECK Q500
PHILIPS	N/A	20C8	NO VOLUME CTRL.--DOESN'T MUTE ON CHANNEL CHANGE	CHECK IC280
PHILIPS	N/A	20C8	SHORT VERTICAL SWEEP	CHECK/REPLACE R239 (10meg?
PHILIPS	N/A	20C8	PICTURE IS SHIFTED 8 TO 10 INCHES TO THE RIGHT - HORZ. BLANKING BAR IS IN THE CENTER OF THE SCREEN	CHECK/REPLACE R501 AND R502 FOR OPEN
PHILIPS	N/A	20C8	DEAD SET-NO REG B+	CHECK IC340 FOR SQR. WAVE @ PIN #11--IF MISSING REPL.
PHILIPS	N/A	20C8	TUNER SEARCHES AFTER CHANNEL IS SELECTED	RESOLDER IC309
PHILIPS	N/A	20C8	DEAD SET-POWER SUPPLY IS OK-NO HORZ. DRIVE	CHECK IC201 AND Q500
PHILIPS	N/A	20C8	Q501 OVERHEATS/SHORTS--APPEARS FLYBACK SHORTED	CHECK R503 (47 OHM) FOR OPEN OR HIGH RESISTANCE
PHILIPS	N/A	20C8	POOR SOUND FROM LEFT SPEAKER WITH EXPANDED SOUND SWITCH ON.	CHECK/REPLACE IC400 ON THE STEREO DECODER BOARD.
PHILIPS	N/A	20C8	BLANK RASTER OR SLICK RASTER-SOUND OK	CHECK/REPLACE IC580 (VERT. OUTPUT IC)
PHILIPS	N/A	20C8	DEAD SET	CHECK R434 FOR OPEN
PHILIPS	N/A	20C8	INTERMITTENT PIX-BLACKS OUT-AUDIO LEVEL DROPS	CHECK ALL CONNECTIONS ON T500
PHILIPS	N/A	20C8	DEAD SET	CHECK/REPLACE D414,D416,Q406 AND Q407
PHILIPS	N/A	20C8	INTERMITTENT BRIGHTNESS VARIATIONS	CHECK/REPLACE R25 ON CRT BOARD
PHILIPS	N/A	20C8	FULL VOLUME-VOL.CHNG. CAUSES TUNER TO SEARCH	CHECK IC280
PHILIPS	N/A	20C8	NO SOUND - AFTER REPLACING IC280 IT RUNS VERY WARM	CHECK/REPLACE IC280,R284 AND C287
PHILIPS	N/A	20C8	GARBLED SOUND AND POSSIBLY ONLY ON CERTAIN CHANNELS	CHECK/REPLACE Y201 SAW FILTER (P/N 483515497069)
PHILIPS	N/A	20C8	INTERMITTENT LOSS OF HORZ. HOLD AND PIX SHRINKS HORZ.	CHECK R505 FOR CONNECTIONS PROBLEMS
PHILIPS	N/A	20C8	BRIGHT RASTER WITH RETRACE AND DIM VIDEO	CHECK/REPLACE R25 (CRT BOARD)
PHILIPS	N/A	20C8	DEAD SET BUT POWER LED COMES ON WHEN POWER BUTTON IS PUSHED	CHECK/REPLACE Z408 FOR SHORT
PHILIPS	N/A	20C8	LOUD WHISTLE WHEN SET IS OFF-OTHERWISE NORMAL	CHECK R430 (56 OHM) FOR OPEN
PHILIPS	N/A	20C8	DEAD SET	CHECK/REPLACE Q406
PHILIPS	N/A	20C8	PIX SHIFTED TO RIGHT,4' BLACK BAR ON LEFT SIDE	CHECK R508 FOR BREAKING DOWN UNDER LOAD
PHILIPS	N/A	20C8	POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT	CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068)
PHILIPS	N/A	20C8	POOR SOUND FROM LEFT SPKR WITH SOUND EXPAND ON	REPLACE IC400 ON THE SAP BOARD
PHILIPS	N/A	20C8	SHUTDOWN,130V NOT REGULATING OR NOT HIGH ENOUGH	CHECK IC201,IC580,Q400,SCR401,Q402,Q403,Q406,Q407,
PHILIPS	N/A	20C8	WHEN BRIGHTNESS INCREASES,PIX SHRINKS VERTICALLY	CHECK D416 FOR OPEN (OUT OF CIRCUIT)
PHILIPS	N/A	20C8	HERRINGBONE,VERT.JITTER,INT.COLOR,DOUBLE IMAGE	CHECK/REPLACE IC201
PHILIPS	N/A	20C8	NO VIDEO OR LUMINANCE	CHECK/REPLACE LEAKY HORZ.DRIVER XSTR.
PHILIPS	N/A	20C8	PICTURE SIZE VARIES BOTH HORZ. AND VERT.	CHECK/REPLACE C421
PHILIPS	N/A	20C8	INTERMITTENT SOUND OR FULL VOLUME WITH NO CONTROL	CHECK/RESOLDER ALL CONNECTIONS ON THE BOTTOM OF THE 'IF' CAGE TO THE PCB.
PHILIPS	N/A	20C8	DEAD SET - STANDBY VOLTAGE IS TOO HIGH AND FULL POWER IS SLIGHTLY HIGH (132 VOLTS)	CHECK/REPLACE Q500
PHILIPS	N/A	20C8	NO PIX-RASTER AND SOUND OK	CHECK C642 SHORTED
PHILIPS	N/A	20C8	WHITE SMOOTH RASTER (NO VIDEO) - SOUND OK	CHECK/REPLACE C631 AND IC640
PHILIPS	N/A	20C8	NO STANDBY VOLTAGES	REPLACED R407/INDUCTOR L402
PHILIPS	N/A	20C8	BRIGHT SCREEN WITH NO VIDEO - OSD LOOKS LIKE THE HORZ. PHASE IS OFF AS GRAPHICS ARE SHIFTED	CHECK/REPLACE R501 OR R502 FOR OPEN
PHILIPS	N/A	20C9	VERTICAL JITTER ON VCR OR NON STANDARD SIGNAL	SEE SERVICE LETTER MARCH/APRIL 1988 ISSUE 2
PHILIPS	N/A	20C9	NO SOUND,COLOR OR BRIGHTNESS - ONLY DIM VIDEO	CHECK/REPLACE IC312
PHILIPS	N/A	20C9	DEAD SET BUT POWER LED COMES ON WHEN POWER BUTTON IS PUSHED	CHECK/REPLACE Z408 FOR SHORT
PHILIPS	N/A	20C9	NO SOUND	CHECK L212
PHILIPS	N/A	20C9	DEAD SET OR SHUTDOWN	CHECK FOR CORRECT VALUE OF R424
PHILIPS	N/A	20C9	NO RASTER OR SOUND	REPLACE IC312
PHILIPS	N/A	20C9	PIX.&AUDIO LEVELS FLUCTUATES INTERMITTENTLY	REPAIR BAD SOLDER JOINT PIN12 ON SWITCH MODETRANST401
PHILIPS	N/A	20C9	INT. DEAD SET OR GOES OFF	CHECK CONNECTIONS ON T401
PHILIPS	N/A	20C9	EXCESSIVE BRIGHTNESS,SHUTSDOWN-LOOKS LIKE VERT. COLLAPSE	CHECK R680 -MUST BE CHECKED OUT OF CIRCUIT
PHILIPS	N/A	20C9	SHUTS DOWN WHILE CHANGING CHANNELS	REPLACE Z503 AND Z504
PHILIPS	N/A	20C9	BRIGHT SCREEN WITH NO VIDEO - OSD LOOKS LIKE THE HORZ. PHASE IS OFF AS GRAPHICS ARE SHIFTED	CHECK/REPLACE R501 OR R502 FOR OPEN
PHILIPS	N/A	20C9	NO RASTER OR SOUND--HIGH VOLTAGE OK	CHECK IC312
PHILIPS	N/A	20C9	DEAD SET-NO REG B+	CHECK IC340 FOR SQR. WAVE @ PIN #11--IF MISSING REPL.
PHILIPS	N/A	20C9	DEAD SET	CHECK R424 ALSO VARACTOR TUNER
PHILIPS	N/A	20C9	DEAD SET AND POWER SUPPLY VOLTAGES ON THE SECONDARY WERE ABOUT 70% OF THE NORMAL VALUE.	CHECK/REPLACE Z408 (CHANGE IN VALUE)
PHILIPS	N/A	20C9	LOSS OF HORIZONTAL SYNC. AND LOSS OF COLOR AFTER 5-10 MINS.	CHECK/REPLACE IC201 (TDA4505A)
PHILIPS	N/A	20C9	TUNING SYSTEM LOCKS UP	REPLACE TUNER
PHILIPS	N/A	20C9	SHORT VERTICAL SWEEP	CHECK/REPLACE R239 (10meg?
PHILIPS	N/A	20C9	AUDIO DISTORTION AT LOW VOL. OR WHEN IN MUTE MOD	REPLACED IC501,AUDIO CONTROL IC ON STEREO DECODER MOD
PHILIPS	N/A	20C9	POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT	CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068)
PHILIPS	N/A	20C9	POOR PICTURE RECEPTION	CHECK/REPLACE Y200 (SAW FILTER)
PHILIPS	N/A	20C9	COMPRESSED VERT AFTER WARM UP-FOLD OVER AT TOP	DEFL. YOKE BECOMES SATURATED--REPLACE
PHILIPS	N/A	20C9	COMES ON BUT PIX DIM-NO COLOR-NO O.S.D.	REPLACE IC312
PHILIPS	N/A	20C9	SHUTS DOWN WHEN SCANNING THE CHANNELS	REPLACED ZENERS Z503 Z504
PHILIPS	N/A	20C9	LOSES COLOR PURITY INTERMITTENTLY	CHECK/REPLACE INTERMITTENT T401
PHILIPS	N/A	20C9	POWER LIGHT COMES ON BUT SET IS DEAD	CHECK/REPLACE Z408
PHILIPS	N/A	20C9	DEAD SET	REPLACED DEFECTIVE U/V TUNER
PHILIPS	N/A	20C9	DEAD SET	REPLACED OPEN R424
PHILIPS	N/A	20C9	GARBLED SOUND AND POSSIBLY ONLY ON CERTAIN CHANNELS	CHECK/REPLACE Y201 SAW FILTER (P/N 483515497069)
PHILIPS	N/A	20C9	DEAD SET-NO REGULATED B+	CHECK IC340 FOR SQR WAVE AT PIN #11-REPL. IF MISSING
PHILIPS	N/A	20D5	DEAD SET	CHECK/REPLACE R432 (1K )
PHILIPS	N/A	20D5	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20D5	DISTORTED AUDIO OR NO AUDIO	CHECK/REPLACE L221 (P/N# 483515757113)
PHILIPS	N/A	20D5	INTERMITTENT OR MISSING ONE PRIMARY COLOR	CHECK/REPLACE Q21,Q22 OR Q23 ON CRT BOARD - MAY BE LABELED AS Q1,Q2,Q3 (P/N# 483513047059)
PHILIPS	N/A	20D5	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	20D6	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20D6	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	20D6	INTERMITTENT OR MISSING ONE PRIMARY COLOR	CHECK/REPLACE Q21,Q22 OR Q23 ON CRT BOARD - MAY BE LABELED AS Q1,Q2,Q3 (P/N# 483513047059)
PHILIPS	N/A	20E1	SHORT VERT. SWEEP--ABOUT 1' TO 2'	CHECK D554 FOR OPEN
PHILIPS	N/A	20E5	NO AUDIO	CHECK/REPLACE STEREO MODULE
PHILIPS	N/A	20E5	WASHED OUT OSD OR BLACK BACKGROUND IN THE MENUS	CHECK/REPLACE IC345 (P/N# 483520988214)
PHILIPS	N/A	20E5	NO SOUND OR PICTURE THROUGH THE JACK PANEL	CHECK/REPLACE R421 (P/N# 482211130483)
PHILIPS	N/A	20E5	NO VERTICAL SWEEP	CHECK/REPLACE C447 (P/N# 483512447498) AND R445 (1?@ 1/2w)
PHILIPS	N/A	20E5	DARK PICTURE	CHECK/RESOLDER CONNECTIONS ON R669
PHILIPS	N/A	20E5	NO PICTURE AND NO HIGH VOLTAGE	CHECK/REPLACE Q502 AND CONNECTIONS ON T504
PHILIPS	N/A	20E5	SET SEARCHES IN THE CABLE MODE THREE TIMES BEFORE LOCKING	CHECK/REPLACE R275 (P/N# 483511067062)
PHILIPS	N/A	20E5	DEAD SET	CHECK/REPLACE R432 (P/N# 483511657582)
PHILIPS	N/A	20E5	ERRATIC KEYBOARD OPERATION AND/OR AFT PROBLEMS	CHECK/REPLACE Q273
PHILIPS	N/A	20E5	SHORT VERTICAL SWEEP	CHECK/REPLACE Z561 (P/N# 483513037777)
PHILIPS	N/A	20E5	NO PICTURE BUT SOUND IS OK	CHECK/REPLACE R460 (P/N# 482211130492)
PHILIPS	N/A	20E5	SET WON'T SHUT OFF	CHECK/REPLACE IC401 (STR30130)
PHILIPS	N/A	20E5	OSD MAY BE MISSING OR SHIFTED	CHECK/REPLACE L357 (P/N# 483515057068)
PHILIPS	N/A	20E5	INTERMITTENTLY REMOTE DOESN'T WORK OR SET LOCKS UP	CHECK/REPLACE MICROPROC. W/NEW TYPE IC (P/N# 483520988291)
PHILIPS	N/A	20E5	TV IS STUCK IN THE DEMONSTRATION MODE	PRESS VOLUME UP/VOLUME DOWN AT THE SAME TIME TO END DEMO
PHILIPS	N/A	20E5	DEAD SET	CHECK/REPLACE R432 (1K )
PHILIPS	N/A	20E5	NO COLOR ON ONE OR MORE CHANNELS - INTERMITTENT COLOR - SLOW COLOR LOCK	CHECK/REPLACE Y620 (P/N# 483524277022)
PHILIPS	N/A	20E5	DEAD SET - COULD BE AN INTERMITTENT PROBLEM	CHECK/REPLACE Q502 (2SD1555) AND F401 (P/N# 483525397031) OR CONNECTIONS ON THE COLLECTOR OF Q502
PHILIPS	N/A	20E5	NO PICTURE OR RASTER	CHECK/REPLACE IC550 AND IC270 (P/N# 483520988106)
PHILIPS	N/A	20E5	NO OSD	CHECK/REPLACE L357 (P/N# 483515057068)
PHILIPS	N/A	20E5	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20E6	NO PICTURE OR RASTER	CHECK/REPLACE IC550 AND IC270 (P/N# 483520988106)
PHILIPS	N/A	20E6	INTERMITTENTLY REMOTE DOESN'T WORK OR SET LOCKS UP	CHECK/REPLACE MICROPROC. W/NEW TYPE IC (P/N# 483520988291)
PHILIPS	N/A	20E6	NO OSD	CHECK/REPLACE L357 (P/N# 483515057068)
PHILIPS	N/A	20E6	WASHED OUT OSD OR BLACK BACKGROUND IN THE MENUS	CHECK/REPLACE IC345 (P/N# 483520988214)
PHILIPS	N/A	20E6	NO VERTICAL SWEEP	CHECK/REPLACE C447 (P/N# 483512447498) AND R445 (1?@ 1/2w)
PHILIPS	N/A	20E6	DARK PICTURE	CHECK/RESOLDER CONNECTIONS ON R669
PHILIPS	N/A	20E6	NO AUDIO	CHECK/REPLACE STEREO MODULE
PHILIPS	N/A	20E6	DEAD SET	CHECK/REPLACE R432 (1K )
PHILIPS	N/A	20E6	SHORT VERTICAL SWEEP	CHECK/REPLACE Z561 (P/N# 483513037777)
PHILIPS	N/A	20E6	OSD MAY BE MISSING OR SHIFTED	CHECK/REPLACE L357 (P/N# 483515057068)
PHILIPS	N/A	20E6	DEAD SET	CHECK/REPLACE R432 (P/N# 483511657582)
PHILIPS	N/A	20E6	NO PICTURE BUT SOUND IS OK	CHECK/REPLACE R460 (P/N# 482211130492)
PHILIPS	N/A	20E6	DEAD SET - COULD BE AN INTERMITTENT PROBLEM	CHECK/REPLACE Q502 (2SD1555) AND F401 (P/N# 483525397031) OR CONNECTIONS ON THE COLLECTOR OF Q502
PHILIPS	N/A	20E6	TV IS STUCK IN THE DEMONSTRATION MODE	PRESS VOLUME UP/VOLUME DOWN AT THE SAME TIME TO END DEMO
PHILIPS	N/A	20E6	SET SEARCHES IN THE CABLE MODE THREE TIMES BEFORE LOCKING	CHECK/REPLACE R275 (P/N# 483511067062)
PHILIPS	N/A	20E6	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20E6	NO PICTURE AND NO HIGH VOLTAGE	CHECK/REPLACE Q502 AND CONNECTIONS ON T504
PHILIPS	N/A	20E6	NO SOUND OR PICTURE THROUGH THE JACK PANEL	CHECK/REPLACE R421 (P/N# 482211130483)
PHILIPS	N/A	20E6	NO COLOR ON ONE OR MORE CHANNELS - INTERMITTENT COLOR - SLOW COLOR LOCK	CHECK/REPLACE Y620 (P/N# 483524277022)
PHILIPS	N/A	20F1	NO COLOR	CHECK/REPLACE Q640
PHILIPS	N/A	20F1	WASHED OUT VIDEO - COLORS SMEAR WHEN ADJUSTING THE CUTOFF CONTROLS	CHECK/REPLACE Q641,Q642 AND Q643 FOR E-B SHORT
PHILIPS	N/A	20F1	REPEATED AUDIO OUTPUT FAILURES	CHECK TWEETER FOR SHORT (IT SHOULD CHECK OPEN)
PHILIPS	N/A	20F1	NO VIDEO	CHECK/REPLACE Y609
PHILIPS	N/A	20F1	SNOWY RASTER AND AUDIO FROM ONE CHANNEL IS ALL THAT CAN BE HEARD - CHANNEL NUMBER DOES CHANGE	CHECK/REPLACE TUNER OR PRESCALER IC INSIDE TUNER IC - (P/N# 483520987893)
PHILIPS	N/A	20F1	DEAD SET-NO POWER-FUSES ALL OK	CHECK R471 FOR OPEN
PHILIPS	N/A	20F1	NO START UP - DEAD SET	CHECK/RESOLDER CONNECTIONS ON R450 AND R452 ALSO CHECK/REPLACE IC400 (P/N# STR30130)
PHILIPS	N/A	20F1	NO VIDEO	CHECK/REPLACE D640
PHILIPS	N/A	20F1	HORZ. FREQUENCY DRIFTS	CHECK/REPLACE R247
PHILIPS	N/A	20F1	SET GOING INTO SHUTDOWN	CHECK IC400
PHILIPS	N/A	20F1	AUD. OUT FAILURE--C211 TO 1uF C206 TO 470pF	PARALLEL R202 W/470pF R207 10 OHM R213,214 130 OHM
PHILIPS	N/A	20F1	NO PICTURE - SOUND OK - HV OK	CHECK/REPLACE T501 (P/N# 483514887065)
PHILIPS	N/A	20F1	NO COLOR	CHECK/REPLACE R638
PHILIPS	N/A	20G6	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20H1	INTERMITTENT SOUND OR A BUZZ IN SOUND	CHECK/REPLACE C205 (SMD)
PHILIPS	N/A	20H1	PICTURE SHRINKS ON BRIGHT SCENES (USUALLY AFTER Q410 HAS FAILED)	CHECK/REPLACE R424 AND R425 (THESE CANNOT BE MEASURED ACCURATELY)
PHILIPS	N/A	20H1	THIN 1/4' LINE DOWN LEFT SIDE OF PICTURE ABOUT 3' FROM THE EDGE. NOT PRESENT IN THE PIP PIX OR VIDEO OUTPUT JACK	CHECK/REPLACE Q500 (6105549001)
PHILIPS	N/A	20H1	NO OR INTERMITTENT COLOR	CHECK/REPLACE C661 (SMD)
PHILIPS	N/A	20H1	JAIL BARS IN LEFT SIDE OF PICTURE	CHECK/REPLACE Q500 (SHOULD NOT BE MOTOROLA)
PHILIPS	N/A	20H1	SKIPS CHANNELS-TURN OFF TIME AT TURN ON	REPLACE MICROCOMPUTER WITH UPDATED VERSION
PHILIPS	N/A	20H1	DEAD SET WITH NO BLOWN FUSES	CHECK/REPLACE Q501 FOR SHORTS
PHILIPS	N/A	20H1	INTERMITTENT OR NO COLOR	CHECK/REPLACE C661
PHILIPS	N/A	20H1	FAILURE OF VERTICAL OUT.IC FROM CRT ARCING	ADD DIODE P/N 5303177001 W/ANODE TO PIN 3 OF IC550
PHILIPS	N/A	20H1	SQUEAL FROM CHASSIS WHILE ON	CHECK/REPLACE C416 (USUALLY PHYSICAL DAMAGE) USE P/N 002530083329
PHILIPS	N/A	20H1	JAIL BARS IN LEFT SIDE OF PICTURE	CHECK/REPLACE L504 WITH NEW PART (362113-6)
PHILIPS	N/A	20H1	CLOCK DOES NOT UPDATE OR RUN	CHECK/REPLACE IC301
PHILIPS	N/A	20H1	NO SOUND BUT DOES HAVE A HISS OR HUM IN SPEAKERS	CHECK/REPLACE C205 (0.01uF SMD)
PHILIPS	N/A	20H1	HIGH BRIGHTNESS WITH RETRACE LINES	CHECK/REPLACE D502 AND R512
PHILIPS	N/A	20H1	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/RESOLDER CONNECTIONS ON Q410
PHILIPS	N/A	20H1	INTERMITTENT SQUEAL FROM CHASSIS	CHECK SMD C427 (2530081029) / ALSO C416
PHILIPS	N/A	20H1	DEAD SET -(Q410 SHORTED AND R403 OPEN)	REPLACE IC401,Q410 AND R403
PHILIPS	N/A	20L1	SET GOES INTO SHUTDOWN WHEN COLD--LATER ATTEMPTS TO TURN- ON MAY BE SUCCESSFUL.	CHANGE Q422 TO P/N(483513047056)-Z422 (483513037086) ADD 330pF(483512247058)PARALLEL C506 IF C505 4700pF
PHILIPS	N/A	20L1	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20L1	BLACK VERTICAL BAR ON SCREEN	CHECK/REPLACE R512 FOR OPEN
PHILIPS	N/A	20L1	ERRATIC CUSTOMER ADJUSTMENTS	CHECK/REPLACE IC350
PHILIPS	N/A	20L1	STAND-BY AND RESET VOLTAGES MISSING	CHECK/REPLACE Q531 (OVER-VOLTAGE SHUT-DOWN LATCH)
PHILIPS	N/A	20L1	NO PIX - WHEN G1 WAS INCREASED,THEN THERE WAS NO VERT. SWEEP.	CHECK/REPLACE FLYBACK IF PINS #2 & #3 ARE OPEN.
PHILIPS	N/A	20L1	SLUGGISH TRANSMITTER RESPONSE	REPLACE MICROPROCESSOR WITH UPDATED VERSION
PHILIPS	N/A	20L1	RELAY BUZZES - OTHERWISE SET IS DEAD	CHECK/REPLACE D413 AND R410
PHILIPS	N/A	20L1	NO AUDIO	CHECK/REPLACE R231 (15 1/4w)
PHILIPS	N/A	20L1	NUISANCE SHUTDOWN	CHNG. R520 TO 1.8k R523 TO 130k
PHILIPS	N/A	20L1	DEAD SET	CHECK Y320 (4MHz XTAL)
PHILIPS	N/A	20L1	NO COLOR WHEN SET IS COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20L1	BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO	CHECK Q630,Q631,Q632
PHILIPS	N/A	20L1	ROLLING OR NO VERTICAL SYNC	CHECK/REPLACE C2515
PHILIPS	N/A	20L1	SET GOES INTO SHUTDOWN ON CHANNEL OR SCENE CHANGES	CHANGE R520 TO 1.8k AND R523 TO 130k - READJUST THE HORZ. FREQ. AFTER MODIFICATION
PHILIPS	N/A	20L1	LOSS OF THE HOTEL-MOTEL MODE	REPLACE IC350
PHILIPS	N/A	20L1	RELAY CLICKS - SET HAS HIGH VOLTAGE BUT NO SOUND OR VERTICAL SWEEP	CHECK/REPLACE IC450 FOR OPEN
PHILIPS	N/A	20L1	FLYBACK CHATTERS - NO SOUND OR PIX - ALL SCAN SUPPLIES LOW	CHECK/REPLACE Q421,Q422 OR Z422 FOR LEAKAGE OR BREAKING DOWN UNDER LOAD
PHILIPS	N/A	20L1	SET TURNS ON BY ITSELF OR CANNOT BE TURNED OFF	CHECK/REPLACE D414 FOR LEAKAGE USE 483513037048)
PHILIPS	N/A	20L1	DARK PICTURE OR NO PICTURE	CHECK/REPLACE C2 FOR SHORT ON CRT BOARD
PHILIPS	N/A	20L1	SLOW COLOR LOCK IN AFTER A CHANNEL IS CHANGED	USE A SELECTED CRYSTAL WITH BLUE MARKINGS ON CASE
PHILIPS	N/A	20L1	HIGH PITCHED SOUND FROM FLYBACK	CHECK R465 AND R501--EITHER ONE MAY HAVE INCREASED.
PHILIPS	N/A	20L1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20L1	NO PICTURE,VOLUME IS AT MAXIMUM AND RELAY CHATTERS	CHECK/REPLACE IC430
PHILIPS	N/A	20L1	DEAD SET	CHECK/REPLACE IC401 ANF F401
PHILIPS	N/A	20L1	NO SOUND BUT PICTURE IS FINE	CHECK/REPLACE R231 FOR OPEN
PHILIPS	N/A	20L1	DEAD SET-HORZ DRIVE TO BASE OF Q501 BUT NOTHING ON COLLECT.	CHECK R502 FOR OPEN (47K)
PHILIPS	N/A	20L1	MAY NOT START AT LOW AC	PARALLEL R421 WITH A 15k,3 WATT OR R421 TO 3.9k 5W
PHILIPS	N/A	20L1	NARROW HORIZONTAL SWEEP,VERTICAL FOLDOVER AND VOLUME FLUCUATES UP AND DOWN.	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	20L1	CANNOT CHANGE TINT,COLOR,BRIGHTNESS OR PICTURE CONTROLS	CHECK/REPLACE IC350
PHILIPS	N/A	20L1	OSD GRAPHICS ARE DISTORTED OR HAVE EXTRA DOTS ON SCREEN	REPLACE IC350 (483520987257)
PHILIPS	N/A	20L1	BRIGHT SCREEN WITH RETRACE LINES - G1 WILL NOT CORRECT	CHECK/REPLACE R460,D460 AND C461
PHILIPS	N/A	20L1	NUISANCE BLOWN FUSES FOR NO APPARENT REASON	INCREASE FUSE VALUE BY .5 AMPS TO A 2AMP
PHILIPS	N/A	20L1	BLACK BAR IN PIX AND VERTICAL STRETCHED	CHECK/REPLACE IC450 (REGULATOR)
PHILIPS	N/A	20L1	FLAGGING ON VCR	CHNG.R523 TO 82k
PHILIPS	N/A	20L1	HIGH VOLUME WITH NO CONTROL--SHORT VERT SWEEP	CHECK/REPLACE IC450 (12V REGULATOR)
PHILIPS	N/A	20L1	STANDBY AND RESET VOLTAGES ARE MISSING	CHECK/REPLACE Q531 FOR E-C LEAKAGE
PHILIPS	N/A	20L1	TV COMES ON BY ITSELF-WON'T TURN OFF-NO RECEPTION OR DISPLAY.	CHECK/REPLACE Z410 FOR LEAKY (SHOULD BE 4.9V)
PHILIPS	N/A	20L1	DEAD SET -RELAY CHATTERS DUE TO OVER-VOLTAGE SHUTDOWN	CHECK/REPLACE IC430
PHILIPS	N/A	20L1	DEAD SET BUT DOES TICK A FEW SECONDS WHEN PLUGGED IN	CHECK D413 FOR SHORTS
PHILIPS	N/A	20L1	NO HORZ. OR VERT. SYNC.	CHECK/REPLACE IC200
PHILIPS	N/A	20L1	HORZ. TEARING -- SET TRIES TO FOLDOVER IN THE CENTER	CHECK/REPLACE R502 (47k)
PHILIPS	N/A	20L4	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20L4	NO PICTURE,VOLUME IS AT MAXIMUM AND RELAY CHATTERS	CHECK/REPLACE IC430
PHILIPS	N/A	20L4	HORZ. TEARING -- SET TRIES TO FOLDOVER IN THE CENTER	CHECK/REPLACE R502 (47k)
PHILIPS	N/A	20L4	NARROW HORIZONTAL SWEEP,VERTICAL FOLDOVER AND VOLUME FLUCUATES UP AND DOWN.	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	20L4	NO AUDIO	CHECK/REPLACE R231 (15 1/4w)
PHILIPS	N/A	20L4	DARK PICTURE OR NO PICTURE	CHECK/REPLACE C2 FOR SHORT ON CRT BOARD
PHILIPS	N/A	20L4	ERRATIC CUSTOMER ADJUSTMENTS	CHECK/REPLACE IC350
PHILIPS	N/A	20L4	NUISANCE BLOWN FUSES FOR NO APPARENT REASON	INCREASE FUSE VALUE BY .5 AMPS TO A 2AMP
PHILIPS	N/A	20L4	DEAD SET -RELAY CHATTERS DUE TO OVER-VOLTAGE SHUTDOWN	CHECK/REPLACE IC430
PHILIPS	N/A	20L4	NEGATIVE VIDEO OR POOR PICTURE	CHECK/REPLACE Y603
PHILIPS	N/A	20L4	NO PIX - WHEN G1 WAS INCREASED,THEN THERE WAS NO VERT. SWEEP.	CHECK/REPLACE FLYBACK IF PINS #2 & #3 ARE OPEN.
PHILIPS	N/A	20L4	BLACK BAR IN PIX AND VERTICAL STRETCHED	CHECK/REPLACE IC450 (REGULATOR)
PHILIPS	N/A	20L4	SET GOES INTO SHUTDOWN ON CHANNEL OR SCENE CHANGES	CHANGE R520 TO 1.8k AND R523 TO 130k - READJUST THE HORZ. FREQ. AFTER MODIFICATION
PHILIPS	N/A	20L4	STAND-BY AND RESET VOLTAGES MISSING	CHECK/REPLACE Q531 (OVER-VOLTAGE SHUT-DOWN LATCH)
PHILIPS	N/A	20L4	RELAY BUZZES - OTHERWISE SET IS DEAD	CHECK/REPLACE D413 AND R410
PHILIPS	N/A	20L4	SET GOES INTO SHUTDOWN WHEN COLD--LATER ATTEMPTS TO TURN- ON MAY BE SUCCESSFUL.	CHANGE Q422 TO P/N(483513047056)-Z422 (483513037086) ADD 330pF(483512247058)PARALLEL C506 IF C505 4700pF
PHILIPS	N/A	20L4	RELAY CLICKS - SET HAS HIGH VOLTAGE BUT NO SOUND OR VERTICAL SWEEP	CHECK/REPLACE IC450 FOR OPEN
PHILIPS	N/A	20L4	ROLLING OR NO VERTICAL SYNC	CHECK/REPLACE C2515
PHILIPS	N/A	20L4	CANNOT CHANGE TINT,COLOR,BRIGHTNESS OR PICTURE CONTROLS	CHECK/REPLACE IC350
PHILIPS	N/A	20L4	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20L4	DEAD SET-HORZ DRIVE TO BASE OF Q501 BUT NOTHING ON COLLECT.	CHECK R502 FOR OPEN (47K)
PHILIPS	N/A	20L4	BLACK VERTICAL BAR ON SCREEN	CHECK/REPLACE R512 FOR OPEN
PHILIPS	N/A	20L4	NO SOUND BUT PICTURE IS FINE	CHECK/REPLACE R231 FOR OPEN
PHILIPS	N/A	20L4	DEAD SET	CHECK/REPLACE IC401 ANF F401
PHILIPS	N/A	20L4	STANDBY AND RESET VOLTAGES ARE MISSING	CHECK/REPLACE Q531 FOR E-C LEAKAGE
PHILIPS	N/A	20L4	FLYBACK CHATTERS - NO SOUND OR PIX - ALL SCAN SUPPLIES LOW	CHECK/REPLACE Q421,Q422 OR Z422 FOR LEAKAGE OR BREAKING DOWN UNDER LOAD
PHILIPS	N/A	20L4	TV COMES ON BY ITSELF-WON'T TURN OFF-NO RECEPTION OR DISPLAY.	CHECK/REPLACE Z410 FOR LEAKY (SHOULD BE 4.9V)
PHILIPS	N/A	20L4	NO COLOR WHEN SET IS COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20N1	INTERMITTENT SHUTDOWN, ESPECIALLY WHEN AC IS ABOVE 120v.	CHECK/REPLACE R410 (150k 1/2watt)
PHILIPS	N/A	20N1	NO AUDIO OR DISTORTED AUDIO	CHECK C230 - IT SHOULD BE A 100nF/100V (483512147036)
PHILIPS	N/A	20N1	OSD ROLLS UP THROUGH THE PIX AND CHANNEL NUMBER LAGS CHANNEL CHANGE BY 2 SECONDS	CHECK/REPLACE D750 (MAY CHECK GOOD)
PHILIPS	N/A	20N1	SET SHUTS OFF AT RANDOM	CHECK/REPLACE IC350
PHILIPS	N/A	20N1	DEAD SET OR MAY INTERMITTENTLY START	CHECK FOR PRESENCE OF PHILIPS MICROPROCESSOR - IF USED THEN REMOVE C320 AND C321
PHILIPS	N/A	20N1	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20N1	NO VERTICAL SWEEP	CHECK/REPLACE IC550
PHILIPS	N/A	20N1	DEAD SET - MAY TAKE MORE THAN ONE TRY TO TURN SET ON	CHECK/REPLACE R405
PHILIPS	N/A	20N1	REPEATED FAILURE OF THE HORZ. OUTPUT XSTR.	CHECK/REPLACE Q502 AND CHECK/RESOLDER CONNECTIONS ON T501
PHILIPS	N/A	20N1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C411 (100uF @ 200v)
PHILIPS	N/A	20N1	NO COLOR ON SOME CHANNELS-INT. LOSS OF COLOR	CHNG. C620 TO 10pF
PHILIPS	N/A	20N1	MORE THAN ONE 'ON' COMMAND REQUIRED TO START SET--MAY BE ENCOUNTERED AFTER REPL. OF H.O.T OR IFT	CHECK R405 AND/OR C410 FOR OPEN
PHILIPS	N/A	20N1	NO ON-SCREEN DISPLAY	CHECK/REPLACE Q380 FOR SHORT OR LEAKAGE
PHILIPS	N/A	20N1	NO CONTROL OF THE BRIGHTNESS	CHECK/REPLACE C343 FOR SHORT
PHILIPS	N/A	20N1	MICROPROCESSOR LOCKS UP AND GRAPHICS APPEAR TO BE WASHED OUT.	CHECK/REPLACE IC350 (483520987549)
PHILIPS	N/A	20N1	POOR AFT LOCK - PICTURE SEARCHES	CHECK/REPLACE Q407
PHILIPS	N/A	20N1	BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO	CHECK Q630,Q631,Q632
PHILIPS	N/A	20N1	NO COLOR WHEN SET IS COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20N1	FLAGGING ON CABLE OR VCR	CHNG. R603 TO 1.8k C602 TO .47uF C603 TO 150pF
PHILIPS	N/A	20N1	OSD ROLLS	CHECK/REPLACE D750 AND Q380
PHILIPS	N/A	20N1	FUSE BLOWS FOR NO APPARENT REASON	CHECK JUMPER B67 TO SEE IF ITS TOUCHING C410
PHILIPS	N/A	20N1	TRIES TO SEARCH CONTINUOUSLY BUT NO CHANNELS PRESENT - LOOKS SIMILAR TO AN AFT PROBLEM	CHECK/REPLACE TUNER
PHILIPS	N/A	20N1	INTERMITTENTLY GOES OFF	CHECK/RESOLDER CONNECTIONS ON T501
PHILIPS	N/A	20N1	IC401 FAILURE IN THE POWER SUPPLY - OR NO REGULATION	CHECK/REPLACE IC401 AND Q403
PHILIPS	N/A	20N1	SET SHUTS OFF	CHECK/REPLACE Q310 FOR INTERMITTENT
PHILIPS	N/A	20N1	SLOW COLOR LOCK IN AFTER A CHANNEL IS CHANGED	USE A SELECTED CRYSTAL WITH BLUE MARKINGS ON CASE
PHILIPS	N/A	20N1	TUNING SLOW TO LOCK IN WHILE IN THE CABLE MODE	REPLACE THE MICROCOMPUTER IC
PHILIPS	N/A	20N1	NO REMOTE CONTROL OPERATION - SET WORKS MANUALLY	CHECK/REPLACE IC350 FOR CORRECT VERSION - IF SET HAS A 4MHZ XTAL USE (483520987551),IF 6MHZ USE (483520987549)
PHILIPS	N/A	20N1	NO OSD	CHECK/REPLACE D750 (WHICH IS NOT SHOWN IN THE SERVICE MANUAL)
PHILIPS	N/A	20N1	DEAD SET	CHECK/REPLACE IC401 ANF F401
PHILIPS	N/A	20N1	ERRATIC OSD WHEN SET IS HOT	CHECK/REPLACE IC350
PHILIPS	N/A	20N1	NUISANCE BLOWN FUSES FOR NO APPARENT REASON	INCREASE FUSE VALUE BY .5 AMPS TO A 2AMP
PHILIPS	N/A	20N1	NO CONTROL OF BRIGHTNESS	CHECK/REPLACE C343
PHILIPS	N/A	20N1	DEAD SET BUT 160V STANDBY SOURCE IS PRESENT	CHECK/REPLACE Q404 AND R402
PHILIPS	N/A	20N5	NARROW RASTER - MAY ALSO HAVE FAINT JAILBARS	CHECK/REPLACE C508 WITH 10nF @ 50v (P/N# 483512147461)
PHILIPS	N/A	20N5	NO HORZ. SYNC. OR SET HAS A BLUE SCREEN	CHECK PIN #5 OF IC530 IS HIGH AND ALL INPUTS ARE NORMAL, THEN REPLACE IC530
PHILIPS	N/A	20P1	RADIO INTERFERENCE,DOTS,SWIRLS OR HERRINGBONE SEEN ON PIP VERSIONS.	CHECK/REPLACE PIP MODULE (ISOLATE BY UNPLUGGING J602)
PHILIPS	N/A	20P1	NO COLOR WHEN COLD	CHECK/REPLACE IC600
PHILIPS	N/A	20P1	INTERMITTENT OPERATION - LEDS WOULD LIGHT FOR A SECOND	CHECK/RESOLDER CONECTIONS ON C451 (NEAR FLYBACK)
PHILIPS	N/A	20P1	INTERMITTENT DEAD SET	CHECK/RESOLDER C431
PHILIPS	N/A	20P1	NO COLOR AND VOLTAGES ON IC600 PINS#12,13,14 ARE LOW	CHECK/REPLACE IC600
PHILIPS	N/A	20P1	RELAY CHATTERS	CHECK/REPLACE C405 FOR OPEN
PHILIPS	N/A	20P1	DEAD SET WITH NO STANDBY POWER	CHECK/REPLACE Q420 AND R424
PHILIPS	N/A	20P1	SLOW OR NO COLOR LOCK POSSIBLY ON SOME CHANNELS ONLY AND THIS SET DID HAVE NEW STYLE CRYSTAL WITH BLUE MARKINGS.	CHECK/REPLACE IC600
PHILIPS	N/A	20P1	NOISY OR SQUEALING SOUND COMING FROM SWITCHING TRANSFORMER	CHECK/REPLACE R410 OR R421 FOR OPEN
PHILIPS	N/A	20P1	POOR REGULATION AFTER Q420 WAS REPLACED	REPLACE R427,R428 AND R424
PHILIPS	N/A	20P1	SLOW COLOR LOCK AFTER CHANNEL CHANGE	USE SELECTED CRYSTAL WITH BLUE MARK ON CASE
PHILIPS	N/A	20P1	INTERMITTENT SHUTDOWN AND INTERMITTENT HORZ. DRIVE	CHECK/REPLACE C208 FOR LEAKAGE
PHILIPS	N/A	20P1	SET SHUTS DOWN BUT WITH SCREEN CTRL. ALL THE WAY DOWN, THE SET WILL REMAIN TO RUN WITH WHITE SCREEN WITH RETRACE.	CHECK/REPLACE R11 (100 OHM) ON THE CRT BOARD -- (200 VOLT SOURCE)
PHILIPS	N/A	20P1	INTERMITTENT SHUTDOWN	CHECK/REPLACE R663
PHILIPS	N/A	20P1	POWER SUPPLY GOES INTO SHUTDOWN AT POWER ON OR CHANNEL CHANGE OR SCENE CHANGES.	CHECK/REPLACE R430 (110K) FOR CHANGE IN VALUE.
PHILIPS	N/A	20P1	R429 GETS VERY HOT AFTER A FEW MINUTES	CHECK C430 FOR SHORT ALSO D430
PHILIPS	N/A	20P1	NO VIDEO	CHECK/REPLACE C608 FOR SHORT AND R622 FOR OPEN
PHILIPS	N/A	20P1	BENDING OR TEARING OF THE PIX - MAYBE THERMAL AND ALSO VARY FROM SIGNAL AND AGC LEVELS.	REPLACE IC200 (483520987072)
PHILIPS	N/A	20P1	REMOTE 'OFF' BUTTON MUST BE PRESSED TWICE TO TURN SET OFF.	CHECK/REPLACE IR90 INFRARED RECEIVER
PHILIPS	N/A	20P1	DEAD SET - 5 VOLTS NORMAL BUT RESET LINE LOW	CHECK/REPLACE IC351
PHILIPS	N/A	20P1	NO AUDIO OR VIDEO BUT OSD WORKS OK	CHECK/REPLACE L210
PHILIPS	N/A	20P1	DEAD SET AND RESET PIN #33 STAYS AT 1.5 VOLTS	CHECK/REPLACE IC351
PHILIPS	N/A	20P1	HISS IN SPKRS. W/TV OFF--POP IN SPKR AT TURN ON	REMOVE D280 AND INSTALL NEW DIODE P/N 4835 130 37048
PHILIPS	N/A	20P1	NO HORZ. DRIVE FROM PIN 26 OF IC200	CHECK/REPLACE C222 FOR OPEN
PHILIPS	N/A	20P1	SET COMES ON WITH AUX.VIDEO BUT TUNER AUDIO	REPLACE IC350 WITH NEW VERSION
PHILIPS	N/A	20P1	SET WILL COME ON ONCE AND THEN WON'T SHUT OFF OR IT WILL SHUT OFF AND NOT COME BACK ON.	CHECK/REPLACE IC350 (MICRO-PROCESSOR)
PHILIPS	N/A	20P1	SET GOES OFF INTERMITTENTLY--APPEARS TO SHUTDOWN	CHECK FOR CORRECT SETTING OF THE B+ (130 VOLTS)
PHILIPS	N/A	20P1	NO COLOR	CHECK/REPLACE R614 FOR A CHANGE IN VALUE
PHILIPS	N/A	20P1	SET SHUTS OFF INT. OR WON'T EVEN COME ON	CHECK C431 OR CONNECTIONS ON IT
PHILIPS	N/A	20P1	DEAD SET	CHECK/REPLACE Q420,D430,R427,R428 AND R424.
PHILIPS	N/A	20P1	HIGH PITCHED SQUEAL FROM POWER SUPPLY WHILE ON	REPLACE L421 USING ONLY P/N 483515757054
PHILIPS	N/A	20P1	VERTICAL SWEEP STRETCHED SEVERLY	CHECK/REPLACE IC550
PHILIPS	N/A	20P1	130 VOLT SOURCE IS TOO LOW	CHECK/REPLACE R431 AND IC400
PHILIPS	N/A	20P1	BRIGHT SCREEN WITH RETRACE LINES	CHECK/REPLACE R663 FOR OPEN
PHILIPS	N/A	20P1	NO COLOR ON SOME CHANNELS-INT. LOSS OF COLOR	CHNG. C620 TO 10pF
PHILIPS	N/A	20P1	JAIL BARS ON THE LEFT SIDE OF THE SCREEN	CHECK/REPLACE L502 WITH NEW TYPE (483515757336)
PHILIPS	N/A	20P1	REPEATED FAILURE OF Q420 (FET)	CHECK/REPLACE C412 WITH A 100nF (MAY HAVE A 10nF FROM THE FACTORY)
PHILIPS	N/A	20P1	WASHED OUT PIX - CONTRAST CONTROL HAS NO EFFECT	CHECK/REPLACE Q661
PHILIPS	N/A	20P1	ROLLING/FLAGING/HORZ. TEARING AT TOP OF PICTURE	REPLACE IC200 WITH NEW VERSION (TDA4505B) (USE 483531057062)
PHILIPS	N/A	20P1	NO VERTICAL SWEEP	CHECK/REPLACE R445 FOR OPEN
PHILIPS	N/A	20P1	ERRATIC OSD WHEN SET IS HOT	CHECK/REPLACE IC350
PHILIPS	N/A	20P1	OSD MENU SKIPS THE STEREO AND AUX INPUT FEATURES	CHECK/REPLACE D261
PHILIPS	N/A	20P1	LOW B+ AND NO RASTER	CHECK/REPLACE IC400
PHILIPS	N/A	20P1	PIP DISAPPEARS ON VIDEO GAMES	DO NOT ATTEMPT TO USE PIP WITH NON STANDARD SIGNALS
PHILIPS	N/A	20P1	BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO	CHECK Q630,Q631,Q632
PHILIPS	N/A	20P1	130 VOLT SOURCE IS TOO HIGH	CHECK/REPLACE R430 AND R432 FOR A CHANGE IN VALUE
PHILIPS	N/A	20P1	HIGH FREQUENCY SQUEAL	REPLACE L421
PHILIPS	N/A	20P1	SET TURNS ON THEN MICROPROCESSOR LOCKS UP - WILL NOT TURN BACK OFF - SNOWY RASTER LOCKED ON ONE CHANNEL	CHECK/REPLACE Q337
PHILIPS	N/A	20P1	SET IS SHUTTING DOWN	CHECK/REPLACE R11 (CRT BOARD) FOR OPEN
PHILIPS	N/A	20P1	TUNING SLOW TO LOCK IN WHILE IN THE CABLE MODE	REPLACE THE MICROCOMPUTER IC
PHILIPS	N/A	20P1	DISTORTED AUDIO W/SET ON--HUM OR BUZZ W/SET OFF	C284 AND/OR C294 MISSING --CHECK FOR PRESENCE OF
PHILIPS	N/A	20P1	VOLTAGE AT Z430 IS NOT 5.6v	CHECK/REPLACE Z430 FOR CHANGE OF VALUE
PHILIPS	N/A	20P1	SET SHUTS OFF AT RANDOM	CHECK/REPLACE IC350
PHILIPS	N/A	20P1	SET SHUTS DOWN DURING SCENE CHANGES OR CHANGING CHANNELS	CHECK/REPLACE D661,R663 AND Q661
PHILIPS	N/A	20P1	VERTICAL ROLL ON SOME CABLE CHANNELS	CHANGE R603 TO A 2k
PHILIPS	N/A	20P1	SLOW CHANNEL ACQUISTION IN THE CABLE MODE	CHECK/REPLACE IC380 (5 VOLT SOURCE)
PHILIPS	N/A	20P1	SLOW COLOR PULL IN OR NO COLOR	CHECK Y620 -IF IT IS MARKED 560444-3 IT IS THE WRONG PART--IT SHOULD BE (483524277001)
PHILIPS	N/A	20P1	DEAD SET ,POWER SUPPLY FAILURE	CHECK TO SEE IF R429 IF TOUCHING C450
PHILIPS	N/A	20P1	SET WILL NOT TURN OFF EVEN BY GROUNDING COLLECTOR OF Q433	CHECK/REPLACE IC402
PHILIPS	N/A	20P5	ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM	CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES
PHILIPS	N/A	20P5	VERTICAL JITTER OR BOUNCE ON SOME CBALE CHANNELS	CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038)
PHILIPS	N/A	20P5	CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU	REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25'
PHILIPS	N/A	20P5	VIDEO SMEARS ON BRIGHT OBJECTS	ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND
PHILIPS	N/A	20P5	TV WON'T SHUT OFF	CHECK/REPLACE Q400 (483513047072), Q402 (483513047059), D420 (483513037048),R431 (47 ), R432 (1K ), R437 (4.7 )
PHILIPS	N/A	20P5	VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL	CHECK/REPLACE R222 OPEN (12k? (P/N# 483511657397)
PHILIPS	N/A	20P5	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1m?(P/N# 483511057204)
PHILIPS	N/A	20P6	ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM	CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES
PHILIPS	N/A	20P6	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1m?(P/N# 483511057204)
PHILIPS	N/A	20P6	TV WON'T SHUT OFF	CHECK/REPLACE Q400 (483513047072), Q402 (483513047059), D420 (483513037048),R431 (47 ), R432 (1K ), R437 (4.7 )
PHILIPS	N/A	20P6	DEAD SET	CHECK FOR OPEN TRACE IN GRID 'H6' - ADD INSULATED WIRE FROM AC NUETRAL TO POINT MARKED PIN # 1 OF L400
PHILIPS	N/A	20P6	VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL	CHECK/REPLACE R222 OPEN (12k? (P/N# 483511657397)
PHILIPS	N/A	20P6	A SLIGHT VERTICAL DRIVE LINE MAY BE SEEN	INSTALL JUMPER AT B1 (GRID D2)
PHILIPS	N/A	20P6	VIDEO SMEARS ON BRIGHT OBJECTS	ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND
PHILIPS	N/A	20P6	CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU	REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25'
PHILIPS	N/A	20P6	VERTICAL JITTER OR BOUNCE ON SOME CBALE CHANNELS	CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038)
PHILIPS	N/A	20R1	DIAGONAL LINES IN PIX OR SPOTS	CHECK VALUE OF C443--IT SHOULD BE 47pF
PHILIPS	N/A	20R1	DEAD SET	CHECK/REPLACE Q501 (483513047061)
PHILIPS	N/A	20R1	DEAD SET - WILL NOT TURN ON - APPEARS TO BE A RESET PROBLEM	CHECK/REPLACE C460
PHILIPS	N/A	20R1	NO SOUND BUT DOES HAVE A HISS OR HUM IN SPEAKERS	CHECK/REPLACE C205 (0.01uF SMD)
PHILIPS	N/A	20R1	WHENEVER SERVICING THE R1 CHASSIS	CHECK FOR PRESENCE OF C443 (BE SURE ITS 47pF)
PHILIPS	N/A	20R1	NO LUMINANCE,OUT OF SYNC,SOUND OK AND CHROMA OK	CHECK/REPLACE R623 FOR OPEN
PHILIPS	N/A	20R1	VERTICAL WHITE LINE ON LEFT SIDE OF SCREEN	CHECK VALUE OF R502 (33K) AND R509 (470K)
PHILIPS	N/A	20R5	OSD HAS WRONG LETTERS, WRONG SPELLING OR INCORRECT SPACING	CHECK/REPLACE IC300 (P/N# 483520988385)
PHILIPS	N/A	20R5	PIP PICTURE JITTERS VERTICALLY	CHANGE C1028 WITH 0.047uF (P/N# 483512287503)
PHILIPS	N/A	20R5	PIP VIDEO HAS VERTICAL JITTER ON SOME CHANNELS	REMOVE C1036 AND SHORT WITH A JUMPER
PHILIPS	N/A	20R5	LITTLE OR NO CLOSED CAPTION INFORMATION WHEN PLAYING BACK A RECORDED CABLE PROGRAM	CHANGE C682 TO 0.22uF POLY (P/N# 483513147002) AND CHANGE C358 TO 1uF (P/N# 483512147406) (NEG. TO IC300-#23)
PHILIPS	N/A	20R5	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON PREMIUM DECODED CABLE	CHANGE C682 TO 0.22uF POLY (P/N# 483512147002), ADD 1.2m?(P/N# 483511057204) FROM JUMPER B57 TO B40
PHILIPS	N/A	20R5	LEFT AUDIO INPUT IS DEAD	SOUND IMAGE IS TURNED ON - THE RIGHT CHANNEL IS DESIGNED FOR MONO INPUT
PHILIPS	N/A	20R5	BOUNCE IN THE PIP PICTURE	CHECK/REPLACE Y1002 (P/N# 483515397004)
PHILIPS	N/A	20R5	TUNER SEARCHES IN THE CABLE MODE	CHECK/REPLACE C273 (0.01uF) (P/N# 483512247098)
PHILIPS	N/A	20R5	ERRATIC RANDOM FUNCTIONS OR WRONG FUNCTIONS FOR BUTTONS PUSHED	CHECK/REPLACE FOR LEAKY KEYBOARD SWITCH (P/N# 483527657004)
PHILIPS	N/A	20R5	VERTICAL JITTER ON SOME CABLE CHANNELS	CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038) DO NOT USE AN ELECTROLYTIC
PHILIPS	N/A	20R5	SOUND IMAGE CUTS IN/OUT ON MONO STATIONS - CUSTOMER COMPLAINS 'STEREO CUSTS OUT'	CHECK/REPLACE IC300 (P/N# 483520988462)
PHILIPS	N/A	20R5	SOUND IS RASPY OR SLURRED OR HISSES WITH SOUND IMAGE TURNED ON AND STEREO TURNED ON	REMOVE C722
PHILIPS	N/A	20R5	ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM	CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES
PHILIPS	N/A	20S1	DARK PICTURE OR NO PICTURE	CHECK/REPLACE C2 FOR SHORT ON CRT BOARD
PHILIPS	N/A	20S1	NOISY BACKGROUND OR OVER PEAKED VIDEO	CHANGE R609 TO A 2.7k
PHILIPS	N/A	20S1	NO AUDIO OR INTERMITTENT AUDIO	CHECK/REPLACE Y220 OR COLD SOLDER CONNECTIONS
PHILIPS	N/A	20S1	CANNOT TURN SET OFF	CHECK/REPLACE R438 (680k) FOR OPEN
PHILIPS	N/A	20S1	TOTALLY DEAD	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	20S1	OSD IS OFF CENTER - IT COULD BE SO FAR OFF CENTER THAT IT CAN'T BE SEEN	MOMENTARILY SHORT PINS 12 & 13 TO ENTER TEST MODE - PRESS RESET BUTTON TO GET TO REG.#10 - USE (+/-) TO CENTER
PHILIPS	N/A	20S1	OSD SHIFTED TOO FAR TO THE RIGHT	CHECK/REPLACE IC351
PHILIPS	N/A	20S1	DEAD SET, POSSIBLY AFTER POWER SURGE	CHECK/REPLACE R403 (P/N# 483511247007),D401,D402,D403,D404 (P/N# FOR ALL 483513037059),R407 (P/N# 483511687002)
PHILIPS	N/A	20S1	BLACK AND WHITE PIP MODULE FAILS TO OPERATE	CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048)
PHILIPS	N/A	20S1	DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ******	CHECK/REPLACE R407 (483511687002) AND T502 (483514247015)
PHILIPS	N/A	20S1	SHADING ON THE RIGHT SIDE OF THE PICTURE	CHECK/REPLACE C399 (P/N# 483512217002) - A FEW SETS WERE SENT OUT WITH A 1k RESISTOR IN PLACE OF THE CAPACITOR
PHILIPS	N/A	20S1	DEAD SET	CHECK/REPLACE R407,Q403 AND T502 FOR OPEN WINDING
PHILIPS	N/A	20S1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20S1	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE R435 (130k ) FOR OPEN
PHILIPS	N/A	20S1	FAILURE OF IC430	CHECK/REPLACE IC430 AND Q400 FOR OPEN - ALSO CHECK THE SOLDER CONNECTIONS ON Q400
PHILIPS	N/A	20S1	NO HORZ. SWEEP - ONE VERTICAL WHITE LINE DOWN SCREEN	CHECK/REPLACE L507 FOR OPEN (P/N# 3620280021)
PHILIPS	N/A	20S1	SHORT VERTICAL SWEEP - ABOUT 2'	CHECK/REPLACE R565 FOR OPEN
PHILIPS	N/A	20S1	DEAD SET - F401 BLOWN AND AFTER REPLACING R432 BURNS	CHECK/REPLACE IC430 AND R432 (1K )
PHILIPS	N/A	20S1	NO PICTURE OR VERY DARK PICTURE - NO OSD	CHECK FOR CARBON PATH BETWEEN PINS #7 & #8 ON FLYBACK
PHILIPS	N/A	20S1	REPEATED OR EARLY FAILURE OF IC430	CHECK/REPLACE Q400
PHILIPS	N/A	20S1	NO TUNING ON CHANNELS 15-20 - ALL OTHERS OK	CHECK/REPLACE TUNER (483521047006)
PHILIPS	N/A	20S1	OPERATION OF SET CAUSES INTERFERENCE ON NEAR BY AM RADIOS	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	20S1	R407 FAILS FOR NO APPARENT REASON AND Q403 MAY ALSO BE BAD	CHECK/REPLACE R407 (ONLY P/N 483511687002) - ADD 6.8k IN PARALLEL W/Z406 - CHNG. R502 TO 130 ohm-REPL. Z411 W/2.7k
PHILIPS	N/A	20S1	HUM OR AUDIO BUZZ OR DISTORTED AUDIO	CHECK TO SEE IF C464 IS A 100uF AND C465 IS A 1000pF ( THESE HAVE BEEN INTER-CHANGED ON SOME CHASSIS )
PHILIPS	N/A	20S1	BRIGHT PICTURE WITH RETRACE LINES	CHECK/REPLACE Z410 AND Q410
PHILIPS	N/A	20S1	TEARING OR FLUTTERING LINES IN THE PICTURE AT LOW BRIGHTNESS	ADD A 6.8v ZENER ACROSS R676 WITH CATHODE TO 9v SOURCE - P/N# 483513037487
PHILIPS	N/A	20S1	LOSS OF MEMORY DUE TO GLITCHES IN THE RESET CIRCUIT	CHANGE R305 > 10 ohm, R416 > 2.2k, R417 > 10 ohm, R492 >> REMOVE, C411 > 22uF, D414 > 3.9v ZENER, Z410 > 5.6v ZENER
PHILIPS	N/A	20S1	TEARING IN THE PICTURE AT VARIOUS BRIGHTNESS LEVELS	ADD 22k FROM PIN#40 OF IC265 TO GRD.,CHANGE C617 > 47uF, BRIGHTNESS REG.#11 MAY NEED TO BE RESET FOR BEST PERFORM.
PHILIPS	N/A	20S1	NO REMOTE CONTROL RESPONSE	CHECK/REPLACE IR RECEIVER (483521027003)
PHILIPS	N/A	20S1	REPEATED SEARCHING IN THE CABLE MODE	CHANGE R241 TO A 680k (P/N 483511067143)
PHILIPS	N/A	20S1	WEAK VIDEO - WASHED VIDEO	CHECK/REPLACE Q210
PHILIPS	N/A	20S4	DEAD SET, POSSIBLY AFTER POWER SURGE	CHECK/REPLACE R403 (P/N# 483511247007),D401,D402,D403,D404 (P/N# FOR ALL 483513037059),R407 (P/N# 483511687002)
PHILIPS	N/A	20S4	DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ******	CHECK/REPLACE R407 (483511687002) AND T502 (483514247015)
PHILIPS	N/A	20S4	REPEATED SEARCHING IN THE CABLE MODE	CHANGE R241 TO A 680k (P/N 483511067143)
PHILIPS	N/A	20S4	REPEATED OR EARLY FAILURE OF IC430	CHECK/REPLACE Q400
PHILIPS	N/A	20S4	TEARING OR FLUTTERING LINES IN THE PICTURE AT LOW BRIGHTNESS	ADD A 6.8v ZENER ACROSS R676 WITH CATHODE TO 9v SOURCE - P/N# 483513037487
PHILIPS	N/A	20S4	BRIGHT PICTURE WITH RETRACE LINES	CHECK/REPLACE Z410 AND Q410
PHILIPS	N/A	20S4	DEAD SET	CHECK/REPLACE R407,Q403 AND T502 FOR OPEN WINDING
PHILIPS	N/A	20S4	CANNOT TURN SET OFF	CHECK/REPLACE R438 (680k) FOR OPEN
PHILIPS	N/A	20S4	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE R435 (130k ) FOR OPEN
PHILIPS	N/A	20S4	TOTALLY DEAD	CHECK/REPLACE IC430 (STR30130)
PHILIPS	N/A	20S4	BLACK AND WHITE PIP MODULE FAILS TO OPERATE	CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048)
PHILIPS	N/A	20S4	DEAD SET - F401 BLOWN AND AFTER REPLACING R432 BURNS	CHECK/REPLACE IC430 AND R432 (1K )
PHILIPS	N/A	20S4	OPERATION OF SET CAUSES INTERFERENCE ON NEAR BY AM RADIOS	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	20S4	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20S4	SHORT VERTICAL SWEEP - ABOUT 2'	CHECK/REPLACE R565 FOR OPEN
PHILIPS	N/A	20S4	R407 FAILS FOR NO APPARENT REASON AND Q403 MAY ALSO BE BAD	CHECK/REPLACE R407 (ONLY P/N 483511687002) - ADD 6.8k IN PARALLEL W/Z406 - CHNG. R502 TO 130 ohm-REPL. Z411 W/2.7k
PHILIPS	N/A	20S4	TEARING IN THE PICTURE AT VARIOUS BRIGHTNESS LEVELS	ADD 22k FROM PIN#40 OF IC265 TO GRD.,CHANGE C617 > 47uF, BRIGHTNESS REG.#11 MAY NEED TO BE RESET FOR BEST PERFORM.
PHILIPS	N/A	20S4	WEAK VIDEO - WASHED VIDEO	CHECK/REPLACE Q210
PHILIPS	N/A	20S4	NO HORZ. SWEEP - ONE VERTICAL WHITE LINE DOWN SCREEN	CHECK/REPLACE L507 FOR OPEN (P/N# 3620280021)
PHILIPS	N/A	20S4	LOSS OF MEMORY DUE TO GLITCHES IN THE RESET CIRCUIT	CHANGE R305 > 10 ohm, R416 > 2.2k, R417 > 10 ohm, R492 >> REMOVE, C411 > 22uF, D414 > 3.9v ZENER, Z410 > 5.6v ZENER
PHILIPS	N/A	20S4	FAILURE OF IC430	CHECK/REPLACE IC430 AND Q400 FOR OPEN - ALSO CHECK THE SOLDER CONNECTIONS ON Q400
PHILIPS	N/A	20S4	NO REMOTE CONTROL RESPONSE	CHECK/REPLACE IR RECEIVER (483521027003)
PHILIPS	N/A	20S4	NO PICTURE OR VERY DARK PICTURE - NO OSD	CHECK FOR CARBON PATH BETWEEN PINS #7 & #8 ON FLYBACK
PHILIPS	N/A	20S4	OSD IS OFF CENTER - IT COULD BE SO FAR OFF CENTER THAT IT CAN'T BE SEEN	MOMENTARILY SHORT PINS 12 & 13 TO ENTER TEST MODE - PRESS RESET BUTTON TO GET TO REG.#10 - USE (+/-) TO CENTER
PHILIPS	N/A	20S4	NO TUNING ON CHANNELS 15-20 - ALL OTHERS OK	CHECK/REPLACE TUNER (483521047006)
PHILIPS	N/A	20S4	OSD SHIFTED TOO FAR TO THE RIGHT	CHECK/REPLACE IC351
PHILIPS	N/A	20T1	NO VERTICAL SWEEP	CHECK/REPLACE R445
PHILIPS	N/A	20T1	NOISY PICTURE-OVER PEAKED-TOO SHARP	CHANGE R331 TO A 5.6k (483511137112)
PHILIPS	N/A	20T1	BRIGHT SCREEN WITH RETRACE LINES	CHECK/REPLACE R669 FOR OPEN
PHILIPS	N/A	20T1	BLACK AND WHITE PIP MODULE FAILS TO OPERATE	CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048)
PHILIPS	N/A	20T1	REPEATED FAILURE OF Q501	CHECK/REPLACE WITH CORRECT VALUE - SHOULD BE 8.2k,3watt P/N (483511667103)
PHILIPS	N/A	20T1	DEAD SET OR LOCKED UP - REMOVING AC MAY CAUSE SET TO START	CHECK/REPLACE IC400 (P/N 483513097006)
PHILIPS	N/A	20T1	DISTORTED AUDIO OR STATIC IN THE AUDIO	CHECK/REPLACE R270 AND R271
PHILIPS	N/A	20T1	CLOCK RUNS TOO FAST OR LOSES TIME	CHANGE R388 TO A 16k 2 watt RESISTOR
PHILIPS	N/A	20T1	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33k?
PHILIPS	N/A	20T1	JAILBARS ON LEFT SIDE OF SCREEN	CHANGE L502 TO (P/N# 483515757673) AND L610 TO (P/N# 483515057038) NON-COMB MODELS ONLY
PHILIPS	N/A	20T1	AFTER CUSTOMER SETTINGS ARE SET (COLOR,TINT,LANGUAGE,ETC) AND POWER IS SHUT OFF OR SET UNPLUGGED, SETTINGS ALL CHANGE	CHECK/REPLACE IC351 (P/N# 483520988104)
PHILIPS	N/A	20T1	NO VERTICAL SWEEP	CHECK/REPLACE IC550 AND SMD R563 - ALSO VERIFY THAT C546 IS A .01uF @ 100V AND NOT A .1uF
PHILIPS	N/A	20T1	JAILBARS ON LEFT SIDE OF SCREEN	CHANGE L502 TO (P/N# 483515757673) AND L602 & L610 TO (P/N# 483515057004) COMB MODELS ONLY
PHILIPS	N/A	20T1	DEAD SET OR INTERMITTENT	CHECK/REPLACE T501 OR MAY HAVE POOR CONNECTIONS
PHILIPS	N/A	20U6	DEAD SET - NO HIGH VOLTAGE	CHECK/REPLACE Q500 (P/N# 483513047073)
PHILIPS	N/A	20V5	NO OSD - SET FUNCTIONS FINE OTHERWISE	CHECK/REPLACE L325 OR OPEN TRACE AT PINS# 18 & 19 OF IC300
PHILIPS	N/A	20V5	VOLUME LOSS W/CHANNEL CHANGE,SAP LOCKUP IN FRENCH MENU, SMART CLOCK OFF 1 HR. ** ONLY ON SETS WITH BLUE MENU BOX **	CHECK/REPLACE MICROPROCESSOR (P/N# 483520988505)
PHILIPS	N/A	20V5	DEAD SET EXCEPT POWER LED	CHECK/REPLACE R538
PHILIPS	N/A	20V5	HORZ. OFF FREQUENCY - MAY BE INTERMITTENT	CHECK/REPLACE Y620 (P/N# 483524277215)
PHILIPS	N/A	20V5	NARROW RASTER - LACKING WIDTH	CHECK/REPLACE C512 (P/N# 483512257004) (820pF)
PHILIPS	N/A	20V5	INTERMITTENT CLOSED CAPTION OPERATION - DOUBLE SPACED LINES DROPOUTS OR COMPLETE LOSS.	C358 WAS INSTALLED IN REVERSE (P/N# 483512497175)
PHILIPS	N/A	20V5	POOR VERTICAL SYNC.(ROLL,JITTER,BOUNCE) ON PREMIUM CHANNELS	CHANGE C682 TO 0.22uF POLY CAP (P/N# 483512147002) AND ADD 1.2m?FROM JUMPER B57 TO B40
PHILIPS	N/A	20V5	CANNOT DELETE CHANNELS FROM THE 'SMART SURF' ** RECORD ALL SERVICE MODE REGISTERS BEFORE REPL. PARTS **	CHECK/REPLACE IC300 (P/N# 483520988488) AND IC302 (P/N# 483520988326)- RECORD ALL SERVICE SETTINGS 1ST
PHILIPS	N/A	20V5	'SCREEN DOOR' EFFECT IN PICTURE DETAIL	CHECK/REPLACE Y600 COMB FILTER (P/N# 483515287002)
PHILIPS	N/A	20X1	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33k?
PHILIPS	N/A	20X1	DEAD SET - NO ATTEMPT TO TURN ON	CHECK/REPLACE R449 WITH NEW PART (P/N# 483511657204)
PHILIPS	N/A	20X1	REPEATED FAILURE OF D430A ( 130 VOLT RECTIFIER)	CHANGE TO (P/N# 483513037491) OR (P/N# 483513037114) OR (P/N# 483513037687) ONLY AND NOT ONE LISTED IN MANUAL
PHILIPS	N/A	20X1	JAIL BARS OR VERTICAL SHADED BARS	ADD JUMPER B120 IF MISSING ON CRT BOARD
PHILIPS	N/A	20X1	THERE IS A REMOTE POSSIBILITY OF THE CUSTOMER SETTINGS MAY BE LOST AND SET MAY EXHIBIT NO COLOR,DARK PIX,ETC.	BRING UP 'PERSONAL PREFERANCE FACTORY SETTINGS' -- NO OTHER FIX EXIST FOR THIS PROBLEM
PHILIPS	N/A	20X1	BLACK AND WHITE PIP MODULE FAILS TO OPERATE - SET WORKS FINE OTHERWISE - - Y2 ON PIP MODULE FAILS TO START	CHANGE C21 > 27pF (483512287029) AND C23 > (483512287048)
PHILIPS	N/A	20X1	WASHED OUT PICTURE AND WEAK VIDEO DRIVE	CHECK/REMOVE R620 IF (2) OF THEM EXIST. THERE SHOULD BE ONLY ONE RESISTOR AT THIS LOCATION
PHILIPS	N/A	20X1	FOCUS DRIFTS AND MAY BE RETRACE LINES IN THE PICTURE	CHECK/RESOLDER CONNECTIONS ON THE GROUND PIN #15 ON FLYBACK
PHILIPS	N/A	20X1	DEAD SET	CHECK/REPLACE R449 - CHANGE TO 27 ohm 1 watt (P/N# 483511657204)
PHILIPS	N/A	20X1	JAILBARS OR SHADED BARS	CHECK/REPLACE MISSING JUMPER B120
PHILIPS	N/A	20X1	OSD CLOCK RUNS TOO FAST - GAINS 12 MINUTES AN HOUR - REMOVING POWER TEMPORARILY MAY RESTORE	CHANGE R326 TO 0 ohms (YES 0) (P/N#483511137019) AND R388 TO 16k 2 watt (P/N# 483511667087)
PHILIPS	N/A	20X1	NO COLOR PIP FUNCTIONS	CHECK/REPLACE PIP MODULE (P/N# APP006A022) OR Y415 CRYSTAL WHICH IS THE PROBLEM (P/N# 483524277159)
PHILIPS	N/A	20X6	DEAD SET	CHECK/REPLACE Q502 (P/N# 483513067001) AND F401 (P/N# 483525397031)
PHILIPS	N/A	20X6	VERTICAL HEIGHT WON'T ADJUST CORRECTLY, ESPECIALLY IF UNIT IS HOT	CHECK/REPLACE R559 WITH 910?1/8w (P/N# 483511067238)
PHILIPS	N/A	20Y1	FLAGGING AT TOP - POOR HORZ. SYNC. - 200v LINE INCREASED	CHECK/REPLACE D406 (P/N# 483513037048)
PHILIPS	N/A	20Y1	SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE	CHECK/REPLACE C432 (100uF @ 200v)
PHILIPS	N/A	20Y1	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	20Y1	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE Q502 (P/N# 483513047706) AND F401 (P/N# 483525397031)
PHILIPS	N/A	20Y1	NO VIDEO	CHECK PIP MODULE (483521977517),C301(483512497026),Q210 (483513047126),Q602 (483513047064), R243 (483511657322)
PHILIPS	N/A	20Y1	NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE	CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831)
PHILIPS	N/A	20Y1	REMOTE WILL RESPOND TO REMOTES FOR OTHER PRODUCTS SUCH AS AUDIO,VCR, ETC.	CHECK/REPLACE IC350 WITH NEW TYPE (P/N# 483520988286)
PHILIPS	N/A	20Y1	DEAD SET - NO ATTEMPT TO START	CHECK/REPLACE Q402 (P/N# ECG382)
PHILIPS	N/A	20Y1	WON'T SHUT OFF - COMES ON WHEN PLUGGED IN	CHECK/REPLACE R438 (680k 1/2w)
PHILIPS	N/A	20Y1	SHORT VERTICAL SWEEP OR FOLDOVER	CHECK/REPLACE Q560 (P/N# 483513047064) AND R552 (P/N# 483511657322)
PHILIPS	N/A	20Y1	NO SAP	ADD 270K (P/N# 483511067116) TO PIN #1 OF IC700 TO GRD.
PHILIPS	N/A	20Y1	HORZ. IS OFF FREQUENCY	CHECK/REPLACE IC410 (P/N# 483520947056)
PHILIPS	N/A	20Y1	DISTORTED AUDIO OR NO AUDIO	CHECK/REPLACE L221 (P/N# 483515757113)
PHILIPS	N/A	20Y1	CHANNEL NUMBERS CHANGE, BUT CHANNELS DON'T	CHECK/REPLACE PIP MODULE (P/N# 483521977517)
PHILIPS	N/A	20Y1	TOTALLY DEAD	CHECK/REPLACE IC410 (STR30130)
PHILIPS	N/A	20Y1	HORIZONTAL OUTPUT FAILURE	CHECK/REPLACE C504 (483512147278)
PHILIPS	N/A	20Y1	VERTICAL OUTPUT FAILURE	CHECK/REPLACE IC550 AND C447 (P/N# 483512447013)
PHILIPS	N/A	20Y1	POOR CONTRAST AND BRIGHTNESS	CHECK/REPLACE Q510 (P/N# 483513047064), R468 (482211130483)
PHILIPS	N/A	20Y1	AM RADIO INTERFERENCE	CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173)
PHILIPS	N/A	20Y1	NO CLOSED CAPTION	CHECK/REPLACE B10 AND B70
PHILIPS	N/A	20Y1	NO VIDEO OR POOR CONTRAST	CHECK/REPLACE C511 (P/N# 483512247224), R538 (483511657427)
PHILIPS	N/A	20Y1	SET WILL NOT TURN ON/OFF	CHECK IC410 (P/N# 483520947056), Q400 (483513047072), R438 (P/N# 483511657518), R432 (P/N# 483511657108)
PHILIPS	N/A	20Y1	DEAD SET	CHECK/REPLACE Z402 (P/N# 483513037003), Z406 (483513037121)
PHILIPS	N/A	20Y1	OSD SHIFTED	CHECK/REPLACE IC346 (P/N# 483520988108)
PHILIPS	N/A	20Y1	TUNER WILL NOT TUNE ANY CHANNELS	CHECK/REPLACE R360 AND R361 (P/N# 483511657275)
PHILIPS	N/A	20Y1	POOR PICTURE	CHECK/REPLACE Z463 (P/N# 483513037121)
PHILIPS	N/A	20Y1	HORZ. RUNNING OFF FREQUENCY	CHECK/REPLACE Z530 (P/N# 483513037121)
PHILIPS	N/A	20Y1	NO AUDIO	CHECK/REPLACE Q95 (P/N# 483513047094), Q703 (483513047086), AND IC230 (P/N# 483520947005)
PHILIPS	N/A	20Y1	NO VIDEO OR OSD	CHECK/REPLACE L630 (P/N# 483515757947),D508 (483513037048) L340 (P/N# 483515757141), R6 (483511657318 - CRT BOARD)
PHILIPS	N/A	20Y1	CLOSED CAPTION IS MISSING FROM THE MENU AND IS TURNED ON	CHECK/RESOLDER CONNECTIONS ON B70 AND B10
PHILIPS	N/A	20Y4	CLOSED CAPTION IS MISSING FROM THE MENU AND IS TURNED ON	CHECK/RESOLDER CONNECTIONS ON B70 AND B10
PHILIPS	N/A	20Y4	DEAD SET OR WON'T SHUT OFF OR WON'T TUNE	CHECK/REPLACE IC345
PHILIPS	N/A	20Y4	NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE	CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831)
PHILIPS	N/A	25A5	VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK	LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33k?
PHILIPS	N/A	25B1	INTERMITTENT SHUTDOWN OR VERT. SWEEP	REPLACE Z670 (LEAKY)
PHILIPS	N/A	25B1	INT. SHUTDOWN OR LOSS OF VERT.SWEEP	Z670 LEAKY
PHILIPS	N/A	25B1	SET WOULD NOT TUNE FOR 1/2 HOUR	REPLACED C399
PHILIPS	N/A	25B1	AUDIO OUTPUT FAILURES---REPL.C211 1uF C206 470pF	PARALLEL 470pF @ R202 R207 10 OHM R213&R214 130 OHM
PHILIPS	N/A	25B1	DEAD SET AND MAY BE INTERMITTENT	CHECK/REPLACE Y300
PHILIPS	N/A	25B1	EXCESSIVE B+ - 130V SOURCE TOO HIGH	CHECK/REPLACE R409
PHILIPS	N/A	25B1	POP IN AUDIO AT TURN OFF	INST. COUPLING CAP.(0.1uF) PIN 6 OF AUDIO IC
PHILIPS	N/A	25B1	NO SOUND AND NO RASTER -IC250 LATCHES UP	REPLACE Q370 AND IC250
PHILIPS	N/A	25B1	DISTORTED AUDIO	CHECK/REPLACE R210 AND Q210
PHILIPS	N/A	25B1	VERTICAL LINE ON THE LEFT SIDE OF THE SCREEN	INSTALL A FERRITE BEAD ON EMITTER OF Q503 (HORZ DRVR)
PHILIPS	N/A	25B1	VERY INTERMITTENT BURST OF SOUND WHILE SET IS TURNED OFF	CHECK/RESOLDER PRIMARY CONNECTIONS ON T471
PHILIPS	N/A	25B1	TUNER HUNTS ON CHANNEL CHANGES 4 TIMES - AFT PROBLEMS	CHECK R342 FOR INCREASE IN VALUE
PHILIPS	N/A	25B1	POP OR CHIRP IN THE AUDIO AT TURN OFF	CHECK FOR A 0.1uF AT PIN #6 OF IC (COUPLING CAP.)
PHILIPS	N/A	25B1	INTERMITTENT SHUTDOWN OR LOSS OF VERTICAL SWEEP	CHECK/REPLACE Z670 (P/N# 5301571270)
PHILIPS	N/A	25B1	GOES INTO SHUTDOWN	REPLACE R409
PHILIPS	N/A	25B1	DEAD SET	REPLACED IC400
PHILIPS	N/A	25B1	NO COLOR	CHECK/REPLACE R516 OPEN
PHILIPS	N/A	25B1	TUNER SEARCHES - POOR AFT LOCK	CHECK/REPLACE IC250 - CHECK ALIGNMENT OF L243
PHILIPS	N/A	25B1	NO PICTURE,NO COLOR AND NO RASTER	CHECK/REPLACE Q516 (P/N# 6104359001)
PHILIPS	N/A	25B1	DEAD SET-MAY BE INTERMITTENT	CHECK CONNECTIONS ON R335
PHILIPS	N/A	25B1	DEAD SET TICKING SOUND	REPAIRED BROKEN SOLDER CONNECTION ON R335
PHILIPS	N/A	25B1	POOR OR SNOWY RECEPTION	CHECK/REPLACE Q220 AND Q311 WITH (P/N# 610434004)
PHILIPS	N/A	25B1	NO PICTURE - NO SOUND AND NO RASTER	CHECK/REPLACE Q370
PHILIPS	N/A	25B1	AUDIO DISTORED AND HAS A BUZZING NOISE VOL.NOT W	REPLACED LEAKY VOLUME CONTROL AMP,Q370
PHILIPS	N/A	25B1	INTERMITTENT SHUTDOWN	CHECK/REPLACE Q690 AND Z689
PHILIPS	N/A	25B1	PICTURE PULSATING FROM PIX TO SNOW	REPLACED R409
PHILIPS	N/A	25B1	SET WOULD NOT LOCK ON STATION	REPLACED Y301
PHILIPS	N/A	25B1	SLOW VERTICAL ROLL - VETTICAL WON'T LOCK	CHECK/REPLACE R237
PHILIPS	N/A	25B1	VERT LINE ON LEFT SIDE OF SCREEN	INST. FERRITE BEAD ON EMITTER OF Q503
PHILIPS	N/A	25B1	VERTICAL FOLDOVER AFTER SET WARMS UP	CHECK/REPLACE D554 (P/N# 5302991001)
PHILIPS	N/A	25B1	SET WAS DEAD OUT-OF-BOX IN CUSTOMERS HOME	REPLACED OPEN R409
PHILIPS	N/A	25B1	DEAD SET OR SHUTS DOWN	CHECK/REPLACE D530 OR Z530

LAMSON Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675  TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:lamsonsm@gmail.com    YAHOO MESSENGER ID : myrna_q_ng or saishu_ng SKYPE ID: myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be using the old address and phone no. in the future. Please be noted when calling us, sending letters, parcels or buying our products> OLD Address: 681 Carmen Building, Ronquillo St. Quiapo, Manila, Philippines Phone:00632-7332936 7332940 Fax:00632-7332940 E-mail: