| MAKE | MODEL | CHASSIS | SYMPTOM | CURE | |
| ACER | 7133S | N/A | Shut Down | resolder plugs on CRT PCB | |
| AMDEK | AM732E | N/A | BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE IC202 (P/N# LM2416) AND R251 (47?@ 1 watt) | |
| AMDEK | AM732E | N/A | HIGH PITCHED SQUEAL FROM POWER SUPPLY AREA | CHECK/RESOLDER CONNECTIONS ON R802,R803 AND R804 | |
| COMPAQ | 420 | N/A | NO VERTICAL SWEEP | CHECK/REPLACE IC202 AND R320 | |
| CTX | CVP5468 | N/A | NO HORZ. SWEEP JUST A VERTICAL WHITE LINE | CHECK/REPLACE C322 | |
| CTX | CVP5468 | N/A | INTERMITTENT LOSS OF ONE OF THE PRIMARY COLORS OR BRIGHT SCREEN WITH RETRACE LINES | CHECK/RESOLDER CONNECTIONS ON CRT SOCKET | |
| DTK | LM2714 | N/A | DEAD SET - POWER SUPPLY SQUEALS | CHECK/REPLACE D005,D006,D007 AND D009 | |
| EMERSON | 1415EM | N/A | POWER SUPPLY SQUEALS - NO POWER | CHECK/RESOLDER CONNECTIONS ON FLYBACK AND HORZ. OUTPUT | |
| EMERSON | 1415EM | N/A | HAS HIGH VOLTAGE BUT NO FILAMENT VOLTAGE | CHECK/REPLACE L4202 FOR OPEN | |
| EMERSON | 1415EM | N/A | DEAD - WILL NOT POWER UP | CHECK/REPLACE IC501 AND R507 | |
| EMERSON | 1440EM | N/A | DEAD - WILL NOT POWER UP | CHECK/REPLACE IC501 AND R507 | |
| EMERSON | 1445EM | N/A | DEAD - WILL NOT POWER UP | CHECK/REPLACE IC501 AND R507 | |
| EMERSON | 4000EM | N/A | DEAD WITH A HIGH PITCHED SQUEAL | CHECK/REPLACE Q104 AND T101 | |
| EMERSON | 4000EM | N/A | SQUEAL FROM HORZ. CIRCUIT-HORZ. CENTERING OFF TO THE LEFT- HORZ. FOLDOVER ON THE LEFT | CHECK/REPLACE Q104 AND C104 FOR OPEN | |
| GATEWAY 2000 | CS1572FS | N/A | SEVERE PIECRUSTING AFTER REPLACEMENT OF HORZ. OUTPUT XSTR. | CHECK/REPLACE L106 (6mH CHOKE) - CHOKE CAN BE REWOUND WITH 230 TURNS OF #26 AWG ENAMELED WIRE | |
| GATEWAY 2000 | CS1572FS | N/A | DEAD SET | CHECK/REPLACE IC301 (P/N# UC3842) | |
| GATEWAY 2000 | CS1572FS | N/A | DEAD SET | CHECK/REPLACE ON Q105 | |
| GATEWAY 2000 | CS1572FS | N/A | DISPLAY SHAKES, POWER SUPPLY SQUEALS OR HISSES | CHECK/REPLACE R331 (91k @ 1watt) | |
| GATEWAY 2000 | CS1572FS | N/A | CLICKS ON/OFF - NO PICTURE | CHECK/REPLACE Q106 (2SD1880), D107 (BY329) AND R153 (1?1w) | |
| GOLDSTAR | 1210 | N/A | NO VIDEO-BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE Q304 FOR SHORT | |
| GOLDSTAR | 1420EGA | N/A | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| GOLDSTAR | 1430VGA | N/A | NO VERT. SWEEP | CHECK IC601,R617 AND R726 | |
| GOLDSTAR | 1430VGA | N/A | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCH4095 | CT5 | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| GOLDSTAR | MCH4095 | CT5 | COMES ON WITH BRIGHT GREY BACKGROUND AND SHORT VERT. SWEEP BUT WORKS FINE AFTER 3-5 MINUTES | CHECK/REPLACE C931 OR C932 FOR OPEN | |
| GOLDSTAR | MCH4175 | CT5 | COMES ON WITH BRIGHT GREY BACKGROUND AND SHORT VERT. SWEEP BUT WORKS FINE AFTER 3-5 MINUTES | CHECK/REPLACE C931 OR C932 FOR OPEN | |
| GOLDSTAR | MCH4175 | CT5 | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| GOLDSTAR | MCH4235 | CT5 | COMES ON WITH BRIGHT GREY BACKGROUND AND SHORT VERT. SWEEP BUT WORKS FINE AFTER 3-5 MINUTES | CHECK/REPLACE C931 OR C932 FOR OPEN | |
| GOLDSTAR | MCH4235 | CT5 | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| GOLDSTAR | MCH4335 | CT5 | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCH4336 | N/A | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCH4337 | N/A | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCL4335 | N/A | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCL4336 | N/A | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCL4337 | N/A | NO VERTICAL SWEEP | CHECK IC601,R617,R726 | |
| GOLDSTAR | MCM4095 | N/A | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| GOLDSTAR | MCM4175 | N/A | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| GOLDSTAR | MCM4235 | N/A | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| IBM | 8512 | N/A | NO REGULATION AND B+ VERY HIGH - MAY BLOW OTHER VARIOUS ELECTROLYTICS | CHECK/REPLACE C18 ON POWER SUPPLY MODULE | |
| JVC | TM122 | N/A | NO PICTURE OR BRIGHT PICTURE WITH NO VIDEO | CHECK/REPLACE Q11 ON CRT BOARD WITH NEW TYPE (P/N# 2SB1110) | |
| JVC | TM63U | N/A | NO VIDEO OUTPUT | CHECK/REPLACE D506 | |
| JVC | TM900SU | N/A | NO PICTURE WHEN POWERED UP | CHECK/REPLACE D506 (P/N# DFA1A4-4) AND R558 (P/N# QRD129J-4R7S) | |
| JVC | TM9010 | N/A | NO PICTURE OR BRIGHT PICTURE WITH NO VIDEO | CHECK/REPLACE Q11 ON CRT BOARD WITH NEW TYPE (P/N# 2SB1110) | |
| JVC | TM9060 | N/A | NO PICTURE OR BRIGHT PICTURE WITH NO VIDEO | CHECK/REPLACE Q11 ON CRT BOARD WITH NEW TYPE (P/N# 2SB1110) | |
| JVC | TM920 | N/A | NO PICTURE OR BRIGHT PICTURE WITH NO VIDEO | CHECK/REPLACE Q11 ON CRT BOARD WITH NEW TYPE (P/N# 2SB1110) | |
| KLH | MN1701 | N/A | WASHED OUT VIDEO - SYMPTOMS LOOK LIKE A OPEN DELAY LINE | CHECK/REPLACE R210 FOR OPEN (220k) | |
| KLH | MN2751 | N/A | DEAD BUT HAS A HIGH PITCHED SQUEAL | CHECK/REPLACE C521 FOR SHORT | |
| MAGINNOVISION | MAG720V2 | N/A | DEAD - SMOKED | CHECK/REPLACE Q305 (P/N# 2SB857) AND IC201 (P/N# TDA8172), R219 (1?1/2w) AND C211 (220uF @ 35V) | |
| MAGINNOVISION | YE071103 | N/A | DEAD - SMOKED | CHECK/REPLACE Q305 (P/N# 2SB857) AND IC201 (P/N# TDA8172) | |
| MITAC | STA439C | N/A | NO PICTURE | CHECK/REPLACE C825 (0.01uF @ 3Kv) | |
| PACKARD BELL | PB1422EG | N/A | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| PACKARD BELL | PB1422EG | CT5 | COMES ON WITH BRIGHT GREY BACKGROUND AND SHORT VERT. SWEEP BUT WORKS FINE AFTER 3-5 MINUTES | CHECK/REPLACE C931 OR C932 FOR OPEN | |
| PACKARD BELL | PB1431EG | N/A | BRIGHT SCREEN (RED,BLUE OR GREEN) WITH RETRACE LINES | CHECK/REPLACE Q617,Q717 OR Q817 FOR SHORT/LEAKY | |
| PACKARD BELL | PB1431EG | N/A | DARK BAR ON THE LEFT SIDE OF THE PICTURE | CHECK/REPLACE C616,C716 AND C816 | |
| PACKARD BELL | PB1431EG | N/A | NARROW WIDTH AND NO PINCUSHION CORRECTION | CHECK/REPLACE Q511 | |
| PACKARD BELL | PB1431EG | N/A | DELAY IN POWER COMING ON | CHECK/REPLACE C921,C923 AND C924 | |
| PACKARD BELL | PB1431EG | N/A | DC SWITCHED MODE POWER SUPPLY VOLTAGES ARE HIGH | CHECK/REPLACE C923,C924 AND C921 | |
| PACKARD BELL | PB1431EG | N/A | NO RASTER AND HV SQUEAL | CHECK/REPLACE Q362,C363 AND Q511 | |
| PACKARD BELL | PB1439EG | N/A | NO VIDEO OR FILAMENT--FRONT LED IS DIM | CHECK FOR OPEN C952 | |
| PHILIPS | 1215DC | N/A | CRACKLING SOUND OR POP IN AUDIO AT POWER UP | CHECK/REPLACE C2257 WITH A 47uF SMD (P/N# 483512447102) | |
| PHILIPS | 20CM64 | N/A | WILL NOT AUTO-SWITCH TO THE DIFFERENT GRAPHICS MODES - EXAMPLE: WILL WORK IN VGA BUT NOT SVGA | CHECK/REPLACE C2433 (P/N# 482212143931) AND RE-ADJUST H-HOLD2 ACCORDING TO SERVICE MANUAL | |
| PHILIPS | 20CM64 | N/A | LINE IN THE CENTER OF PICTURE | CHECK/REPLACE C2506 (P/N# 482212142007) | |
| PHILIPS | 20CM640741 | N/A | DEAD SET --- ADD 33Í@3w (482211683987) PARALLEL WITH R3655 C2607(482212442161), L5604(483515763128), | Q7605(482213063627),Q7615(483513047377),C2609(482212143677) C2608/C2610(482212422676),D6608(482213083128) | |
| PHILIPS | 20CM64BE | N/A | DEAD SET --- ADD 33Í@3w (482211683987) PARALLEL WITH R3655 C2607(482212442161), L5604(483515763128), | Q7605(482213063627),Q7615(483513047377),C2609(482212143677) C2608/C2610(482212422676),D6608(482213083128) | |
| PHILIPS | 6CM320 | N/A | LOSS OF ONE OR MORE PRIMARY COLORS | CHECK/REPLACE IC7301 - CHANGE R3320 TO 4.7k | |
| PHILIPS | 7CM320 | N/A | LOSS OF ONE OR MORE PRIMARY COLORS | CHECK/REPLACE IC7301 - CHANGE R3320 TO 4.7k | |
| PHILIPS | 8CM505 | N/A | SHUTSDOWN INTERMITTENTLY | CHECK/REPLACE C124 | |
| PHILIPS | 8CM515 | N/A | IF THE FLYBACK IS FOUND TO BE DEFECTIVE | CHECK R330,R475,R476,C476 | |
| PHILIPS | CM0200 | N/A | HIGH VOLTAGE IS LOW | CHECK/REPLACE C2902 (P/N# 482212170456) | |
| PHILIPS | CM2099TV | N/A | 3 INCH BAR DOWN THE MIDDLE OF THE SCREEN AND PICTURE IS WRAPPED - MAY BE HEAT RELATED | GROUND DRAIN OF Q7852 AND ADJUST MODE DETECTOR AND HORZ. SYNC ACCORDING TO ADJUSTMENT #3 IN MANUAL - REMOVE GROUND | |
| PHILIPS | CM8702 | N/A | IF THE FLYBACK IS FOUND TO BE DEFECTIVE | CHECK R330,R475,R476,C476 | |
| PHILIPS | CM8762 | N/A | IF THE FLYBACK IS FOUND TO BE DEFECTIVE | CHECK R330,R475,R476,C476 | |
| PHILIPS | CM8764 | N/A | IF THE FLYBACK IS FOUND TO BE DEFECTIVE | CHECK R330,R475,R476,C476 | |
| QUIMAX | DM14 | N/A | DEAD WITH BLOWN B+ FUSE | CHECK D303 (SCAN RECTIFIER) | |
| SAMSUNG | CCB7571 | N/A | VIDEO CROSS TALK WHEN A BLACK COLOR IS SURROUNDED BY A WHITE COLORED BORDER. - ESPECIALLY WHILE USING 'WINDOWS' | CHANGE C516 TO NEW TYPE (P/N 1509-121-1309) | |
| SAMSUNG | CD1451D | N/A | POWER SUPPLY WON'T ALWAYS START UP | R504 FOR OPEN OR INCREASE | |
| SAMSUNG | CD1452GA | N/A | POWER SUPPLY WON'T ALWAYS START UP | R504 FOR OPEN OR INCREASE | |
| SAMSUNG | CD1557SD | N/A | WASHED OUT VIDEO - SYMPTOMS LOOK LIKE A OPEN DELAY LINE | CHECK/REPLACE IC602 (PIN 16 SHOULD A HORZ. PULSE OUT) C | |
| SAMSUNG | CJ4681 | N/A | HORZ. BOWING | CHECK/REPLACE R315 | |
| SAMSUNG | CJ4681 | N/A | HORZ. BOWING OF PICTURE | CHECK/REPLACE R315 | |
| SAMSUNG | CM4531 | N/A | NARROW WIDTH AND NO PINCUSHION CORRECTION | CHECK/REPLACE Q511 | |
| SAMSUNG | CM4531 | N/A | DEAD | CHECK/REPLACE Q511,Q362 AND L363 | |
| SAMSUNG | CM4531 | N/A | NO RASTER AND HV SQUEAL | CHECK/REPLACE Q362,C363 AND Q511 | |
| SAMSUNG | CM4531 | N/A | DELAY IN POWER COMING ON | CHECK/REPLACE C921,C923 AND C924 | |
| SAMSUNG | CM4531 | N/A | NO RASTER AND HAS A HV SQUEAL | CHECK/REPLACE Q362,C363 AND Q511 | |
| SAMSUNG | CM4531 | N/A | DARK BAR ON THE LEFT SIDE OF THE PICTURE | CHECK/REPLACE C616,C716 AND C816 | |
| SAMSUNG | CM4531 | N/A | DC SWITCHED MODE POWER SUPPLY VOLTAGES ARE HIGH | CHECK/REPLACE C923,C924 AND C921 | |
| SAMSUNG | CM4541 | N/A | Q511 AND Q362 SHORTED | CHECK/REPLACE Q511,Q362 AND L363 | |
| SAMSUNG | CQ4551 | N/A | INTERMITTENT BUZZING SOUND FROM POWER SUPPLY AND PIX BLOOMS | CHECK/REPLACE STR53041 IN POWER SUPPLY FOR INTERMITTENT | |
| SAMSUNG | CSD5577 | N/A | WASHED OUT VIDEO - SYMPTOMS LOOK LIKE A OPEN DELAY LINE | CHECK/REPLACE IC602 (PIN 16 SHOULD A HORZ. PULSE OUT) C | |
| SAMSUNG | CSF7487 | N/A | VIDEO CROSS TALK WHEN A BLACK COLOR IS SURROUNDED BY A WHITE COLORED BORDER. - ESPECIALLY WHILE USING 'WINDOWS' | CHANGE C516 TO NEW TYPE (P/N 1509-121-1309) | |
| SAMSUNG | CVB4581 | N/A | VERTICAL INSTABILITY OR VERTICAL FOLDOVER AND SHORT SWEEP | RE-ADJUST VR201 FOR PROPER OPERATION (FACTORY MIS-ADJUSTED) SHOULD BE ADJUSTED IN THE 1024x768 MODE | |
| SAMSUNG | CVB4587 | N/A | VERTICAL INSTABILITY OR VERTICAL FOLDOVER AND SHORT SWEEP | RE-ADJUST VR201 FOR PROPER OPERATION (FACTORY MIS-ADJUSTED) SHOULD BE ADJUSTED IN THE 1024x768 MODE | |
| SAMSUNG | CVB4991 | N/A | VERTICAL INSTABILITY OR VERTICAL FOLDOVER AND SHORT SWEEP | RE-ADJUST VR201 FOR PROPER OPERATION (FACTORY MIS-ADJUSTED) SHOULD BE ADJUSTED IN THE 1024x768 MODE | |
| SAMSUNG | CVB4993 | N/A | VERTICAL INSTABILITY OR VERTICAL FOLDOVER AND SHORT SWEEP | RE-ADJUST VR201 FOR PROPER OPERATION (FACTORY MIS-ADJUSTED) SHOULD BE ADJUSTED IN THE 1024x768 MODE | |
| SAMSUNG | CVB4997 | N/A | VERTICAL INSTABILITY OR VERTICAL FOLDOVER AND SHORT SWEEP | RE-ADJUST VR201 FOR PROPER OPERATION (FACTORY MIS-ADJUSTED) SHOULD BE ADJUSTED IN THE 1024x768 MODE | |
| SAMSUNG | CVM4967T | N/A | NO PINCUSHION CONTROL AFTER A FEW MINUTES OF OPERATION PICTURE PULLS IN ON THE SIDES | CHECK/REPLACE C207 (0.47uF @ 50v) (P/N# 917 120470HM) AND IC202 (LM358) (P/N# 881 100358AANA) | |
| SAMSUNG | CVM4967T | N/A | DEAD - NO ATTEMPT TO TURN ON | CHECK/RESOLDER CONNECTIONS ON POWER SWITCH WHERE IT SOLDERS TO THE MAIN PCB | |
| SAMSUNG | SC431E | N/A | DEAD--BLOWS REGULATOR TRANSISTOR | CHECK FUSE,REGULATOR XSTR.,R905,R906 | |
| SAMSUNG | SM12SFA7 | N/A | INTERMITTENT VERT. SWEEP--COLLAPSES QUICKLY | CHECK FOR LEAKY C304 | |
| SAMSUNG | SM440 | N/A | NARROW HORZ. SWEEP AND STRETCHED VERT. SWEEP | CHECK/REPLACE 24V REGULATOR IC | |
| SAMSUNG | SM460 | N/A | DARK PICTURE OR NO PICTURE | CHECK/REPLACE C512 AND C514 FOR OPEN | |
| SCOTT | SM2350A | N/A | DEAD - WILL NOT POWER UP | CHECK/REPLACE IC501 AND R507 | |
| SCOTT | SM2600 | N/A | SQUEAL FROM HORZ. CIRCUIT-HORZ. CENTERING OFF TO THE LEFT- HORZ. FOLDOVER ON THE LEFT | CHECK/REPLACE Q104 AND C104 FOR OPEN | |
| SCOTT | SM2600 | N/A | DEAD WITH A HIGH PITCHED SQUEAL | CHECK/REPLACE Q104 AND T101 | |
| SOCOS | CM1402 | N/A | NO HORZ. SWEEP -- ONLY HAS A VERTICAL LINE | CHECK/REPLACE C418 (0.56uF @ 250v) | |
| SONY | CDP15SF2 | N/A | OSD IS MISSING OR DISPLAYED INCORRECT | CHECK/REPLACE IC901 (P/N# 8-759-354-66) | |
| SONY | CDP15SF2 | N/A | NO PICTURE WITH WIDE VERTICAL SYNC. PULSE | CHECK/REPLACE IC901 (P/N# 8-759-354-66) AND C948 (P/N# 1-136-169-00) (0.22uF @ 50v) | |
| SONY | CDP17SF2 | N/A | NOISE IN THE LEFT BOTTOM PICTURE | CHECK/REPLACE R008 (P/N# 1-249-413-11) | |
| SONY | CDP17SF2 | N/A | NO PICTURE WITH WIDE VERTICAL SYNC. PULSE | CHECK/REPLACE IC901 (P/N# 8-759-370-67) AND C948 (P/N# 1-136-169-00) (0.22uF @ 50v) | |
| SONY | CDP17SF2 | N/A | OSD IS MISSING OR DISPLAYED INCORRECT | CHECK/REPLACE IC901 (P/N# 8-759-370-67) | |
| SONY | CPD15SF1 | N/A | VIDEO SMEAR OR GHOST WHEN AN ALL WHITE OR ALL BLACK IMAGE IS PLACED ON A GREY BACKGROUND | CHANGE R131,R231,R331 TO 120k ,CHANGE R132,R232,R332 TO 2K ADD R134,R234,R334 4.7k AND C208 5pF @ 50v (1-102-942-00) | |
| SONY | CPD15SX1 | N/A | DEAD OR REPEATED FAILURE OF Q301 | CHECK/REPLACE Q301 AND C323 (P/N# 1-124-903-11 1uF @ 50v) | |
| SONY | CPD17SF2 | N/A | DEAD OR REPEATED FAILURE OF Q507 | CHECK/REPLACE Q507 AND C525 (P/N# 1-126-933-11 100uF @ 16v) | |
| SONY | CPD20SF2 | N/A | NO POWER WHEN UNIT WARMS UP | CHANGE Q608 WITH NEW TYPE (P/N# 8-729-803-76 2SA1371E), AND R655 (P/N# 1-216-344-11 0.39?5% 1w) | |
| SONY | CPD20SF2 | N/A | NO PICTURE - MISSING A COLOR - INCORRECT BRIGHTNESS | CHECK/REPLACE IC005 (P/N# 8-749-011-84), ADD 10uF @ 100v CAPACITOR W/NEG. TO D304 ANODE AND POS. TO D303 CATHODE | |
| SONY | CPD20SF2 | N/A | NO POWER - ORANGE LED BLINKS | CHECK/RESOLDER CONNECTIONS ON C628 (ONE OF THE C628 LEADS MAY BE SHORTING OUT) | |
| SONY | CPD20SF2T | N/A | NO PICTURE - MISSING A COLOR - INCORRECT BRIGHTNESS | CHECK/REPLACE IC005 (P/N# 8-749-011-84), ADD 10uF @ 100v CAPACITOR W/NEG. TO D304 ANODE AND POS. TO D303 CATHODE | |
| SONY | GDM17SE1 | N/A | PICTURE DIMS AND EVENTUALLY DISAPPEARS | CHECK/REPLACE C625 (P/N# 1-123-973-91) | |
| SONY | GDM17SE1 | N/A | NO OPERATION AND FRONT PANEL LED'S ARE FLASHING | REMOVE C511, REMOVE D504 AND INSTALL IT IN C511 PLACE - ALSO CHECK Q511,Q512,PS500 AND C548 | |
| SONY | GDM17SE2T | N/A | NO POWER - ORANGE LED BLINKS | CHECK/RESOLDER CONNECTIONS ON C628 (ONE OF THE C628 LEADS MAY BE SHORTING OUT) | |
| SONY | GDM17SE2T | N/A | NO PICTURE - MISSING A COLOR - INCORRECT BRIGHTNESS | CHECK/REPLACE IC005 (P/N# 8-749-011-84), ADD 10uF @ 100v CAPACITOR W/NEG. TO D304 ANODE AND POS. TO D303 CATHODE | |
| SONY | GDM20SE1 | N/A | NO OPERATION AND FRONT PANEL LED'S ARE FLASHING | REMOVE C511, REMOVE D504 AND INSTALL IT IN C511 PLACE - ALSO CHECK Q511,Q512,PS500 AND C548 | |
| SONY | GDM20SE1 | N/A | PICTURE DIMS AND EVENTUALLY DISAPPEARS | CHECK/REPLACE C625 (P/N# 1-123-973-91) | |
| STANDARD TECH | STA439C | N/A | NO PICTURE | CHECK/REPLACE C825 (0.01uF @ 3Kv) | |
| TANDY | CM11 | N/A | DEAD SET | CHECK/REPLACE Q702,R704 AND R711 | |
| TVM | MD141V+ U07 | N/A | DEAD BUT GREEN POWER LED ON FRONT DOES BLINK ON AND OFF | CHECK/REPLACE D805, D816 AND D818 | |
| ZENITH | ZVM1380F | N/A | BRIGHTNESS LIMITER CIRCUIT NOT WORKING | CHECK/REPLACE R454,Q205,Q413 | |
| ZENITH | ZVM1380F | N/A | RETRACE LINES IN THE PICTURE | CHECK/REPLACE Q504,Q544,Q574,D308,R329,Q505,Q545,Q575 | |
| ZENITH | ZVM1380F | N/A | PICTURE OR COLOR MISSING | CHECK/REPLACE IC201,IC212,Q501,Q502,Q541,Q542,Q543,Q571, Q572,Q503,Q543,Q573,Q504,Q505,Q506,Q544,Q545,Q574,Q575,Q576 | |
| ZENITH | ZVM1380F | N/A | NO HORZ. SWEEP | CHECK/REPLACE Q403,Q404,L401,C415,Q405 | |
| ZENITH | ZVM1380F | N/A | NO VERTICAL SWEEP | CHECK/REPLACE R320,Q302,Q303,IC401,Q301 | |
| ZENITH | ZVM1380F | N/A | RASTER IS TOO WIDE | CHECK/REPLACE R433,Q205,C417,C414,L401,D407 | |
| ZENITH | ZVM1380F | N/A | NO PICTURE | CHECK/REPLACE Q408,Q407 AND R444 | |
| ZYNK | SM1418 | N/A | POWER SUPPLY CHIRPS - NO PICTURE | CHECK/REPLACE Q203 (ECG379) | |
| ZYNK | SM1418 | N/A | COMPRESSED VERTICAL SWEEP AT THE TOP | CHECK/REPLACE C405 AND C406 (100uF @ 16v) | |
| ZYNK | SM1418 | N/A | POWER SUPPLY SQUEALS - MONITOR WORKS FINE OTHERWISE OTHER THAN SOME HORZ. TEARING | CHECK/REPLACE C910 |
|
LAMSON
Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675 TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:lamsonsm@gmail.com
YAHOO MESSENGER ID : myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be
using the old address and phone no. in the future. Please be
noted when calling us, sending letters, parcels or buying our products>
|
