CAMCORDER REPAIR TIPS PAGE 1

MAKE	MODEL	CHASSIS	SYMPTOM	CURE
CHINON	CVT70	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
CHINON	CVT70	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
CHINON	CVT70	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
CHINON	CVT70	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
CHINON	CVT70	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
CHINON	CVT70	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
CURTIS MATHES	AV800	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
CURTIS MATHES	AV800	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
CURTIS MATHES	AV850	N/A	DEAD SET	CHECK/REPLACE IC1001
CURTIS MATHES	BV800	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
CURTIS MATHES	BV800	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
CURTIS MATHES	BV800	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
CURTIS MATHES	BV800	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
CURTIS MATHES	BV800	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
CURTIS MATHES	BV800	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
CURTIS MATHES	BV880	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
CURTIS MATHES	CV800	N/A	CHARGER IS DEAD - NO POWER LIGHTS	CHECK/REPLACE C13 FOR SHORT
CURTIS MATHES	MV800	N/A	INTERM. LIT POW/CHARG. LEDS	REPLACE D1006
GE	1CVM6060E	N/A	INTERM. LIT POW/CHARG. LEDS	REPLACE D1006
GE	99605	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99605	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99605	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99605	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99605	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	99605	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99605	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99605	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99605	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	99605	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	99606	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99606	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99606	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99606	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99606	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	99606	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	99606	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99606	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	99607	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99607	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99607	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99607	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	99607	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	99607	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	99607	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99607	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99608	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99608	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99609	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	99609	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	99609	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	99609	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	99609	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99609	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	99610	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99610	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99805	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99806	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	99806	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99807	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99807	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
GE	99807	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	CG400	N/A	UNABLE TO CHANGE SHUTTER SPEEDS	IF THE CP-1 BOARD HAS A MARKING OF 1AG0B10B17051, THEN PIN 58 OF IC916 MUST BE LIFTED
GE	CG400	N/A	POOR COLOR TEMPERATURE	CHANGE VR933 TO 220k (P/N# 230272)
GE	CG400	N/A	SLIGHT BEAT PATTERN VISIBLE IN PLAYBACK VIDEO	CHANGE C3901 TO A 22uF @ 6.3v TANTALUM (P/N# 194537)
GE	CG501	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
GE	CG504	N/A	EXTREMELY DIFFICULT TO PERFORM 'COLOR DIFFERENCE SIGNAL' ADJUSTMENT	CHECK/REPLACE RA813 (P/N# 223499)
GE	CG504	N/A	UNDER CERTAIN LOW VOLTAGE CONDITIONS , THE CAMCORDER MAY SHUT OFF AND NOT ALLOW THE TAPE TO BE EJECTED	CHANGE R14 TO 100?(P/N# 200300)
GE	CG681	N/A	UNIT SHUTS OFF WHEN CASSETTE IS EJECTED	BLUE WIRE ON CASSETTE DOWN SWITCH SHORTING WHEN DOOR OPEN
GE	CG683	N/A	NO AUDIO DURING PLAYBACK BUT DOES RECORD AUDIO OK - PROBLEM SEEMS TO BE INTERMITTENT WITH TEMPERATURE	CHECK/RESOLDER CONNECTIONS ON R401
GE	CG800	N/A	DEW INDICATOR ON - WILL NOT EJECT TAPE	CHECK/RESOLDER CONNECTIONS ON PLUG P7 ON MAIN BOARD
GE	CG805	N/A	DEW INDICATOR ON - WILL NOT EJECT TAPE	CHECK/RESOLDER CONNECTIONS ON PLUG P7 ON MAIN BOARD
GE	CG818	N/A	ERRATIC SPEED IN RECORD OR PLAYBACK	CHECK/REPLACE IC361 (P/N# 213100)
GE	CG9805	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	CG9805	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	CG9805	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	CG9805	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	CG9805	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	CG9805	N/A	CHARGER IS DEAD - NO POWER LIGHTS	CHECK/REPLACE C13 FOR SHORT
GE	CG9805	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	CG9806	N/A	CHARGER IS DEAD - NO POWER LIGHTS	CHECK/REPLACE C13 FOR SHORT
GE	CG9807	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	CG9807	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	CG9807	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	CG9807	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	CG9807	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	CG9807	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	CG9809	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	CG9809	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	CG9809	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	CG9809	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	CG9809	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	CG9809	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	CG9810	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
GE	CG9810	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
GE	CG9810	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
GE	CG9810	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
GE	CG9810	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
GE	CG9810	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
GE	CG9906	N/A	DEAD	CHECK/REPLACE C1010
HITACHI	VM2000A	N/A	AUTO-FOCUS DOESN'T STOP WHERE IT SHOULD	REMOVE SMALL ACCESS DOOR DIRECTLY BELOW LENS AND ADJUST SMALL SCREW INSIDE TO OBTAIN PROPER FOCUS.
HITACHI	VM300A	N/A	WON'T PLAY OR RECORD	CHECK/RESEAT THE RIBBON CABLE TO DRUM MOTOR
HITACHI	VM3300	N/A	LINES THROUGH THE CAMERA VIDEO	CHECK/REPLACE C9 ON CAMERA SECTION
JVC	AAG10U	N/A	UNIT WAS DEAD - FUSE F1 WAS OPEN	CHECK/REPLACE Q2 (2SC2793) FOR SHORT AND F1
JVC	GR15U	N/A	NO ZOOM OR AUTOFOCUS	CHECK/REPLACE IC1 (P/N# HA13475MP) ON AUTOFOCUS BD.
JVC	GR303U	N/A	NO COLOR IN THE MONITOR MODE	CHECK/REPLACE Q102 (P/N# 2SC4655) ON VIDEO BOARD ASSEMBLY
JVC	GR303U	N/A	ALL FUNCTIONS WORK FINE BUT CRT IN VIEWFINDER WON'T WORK	CHECK/REPLACE IC105 (P/N# TK10682M)
JVC	GR323U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GR60U	N/A	INTERMITTENTLY GOES TO STOP MODE	CHECK/REPLACE SW1 (CASSETTE LOCK SWITCH ON D.MDA PCB)
JVC	GR60U	N/A	SELF-RECORDINGS HAVE NO COLOR	CHECK/REPLACE C96 (QER61HM-105GZ) SHORTED
JVC	GR60U	N/A	POOR PLAYBACK AND SELF RECORDED TAPE POOR QUALITY ALSO. TAPES LOOK NORMAL WHEN PALYED ON ANOTHER UNIT.	CHECK/REPLACE Q407 (8VOLT RECORD SWITCH)
JVC	GR60U	N/A	NO PLAYBACK PICTURE - ONLY SNOW	CHECK/REPLACE Q21 (P/N# 2SA1577) ON Y/C BOARD
JVC	GR65U	N/A	INTERMITTENT POWER ON	CHECK/REPLACE IC401 (M37412M4-004FP)
JVC	GRAW1U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GRAX10U	N/A	WILL NOT RECORD AUDIO	CHECK/REPLACE L33 (YU41135-221K) IN THE AUDIO CIRCUIT
JVC	GRAX10U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GRAX10U	N/A	DOES NOT ERASE AUDIO OR VIDEO	CHECK/REPLACE Q16 (P/N # 2SA1577(QR) ) IN THE FLYING ERASE CIRCUIT
JVC	GRAX10U	N/A	INTERMITTENT ' DEW' INDICATOR IN VIEWFINDER	CHECK/RESOLDER WIRES FROM DEW SENSOR DIRECTLY TO PCB
JVC	GRAX10U	N/A	CAMERA VIDEO FADES	CHECK/REPLACE CRYSTAL RESONATOR ON SSG BOARD (YU41617)
JVC	GRAX10U	N/A	COLOR FADES IN THE MONITOR MODE	CHECK/REPLACE IC1 (P/N# HA118130MA) ON THE VIDEO BOARD
JVC	GRAX10U	N/A	POWER DOES NOT STAY ON	CHECK/REPLACE R315 (P/N # NRVA63D-363N)
JVC	GRAX10U	N/A	NO RECORD VIDEO	CHECK/RESOLDER CONNECTIONS ON R659 ON Y/C BOARD
JVC	GRAX10U	N/A	VERTICAL BARS IN THE CAMERA VIDEO	CHECK/RESOLDER CCD DIRECTLY TO IT'S SOCKET
JVC	GRAX10U	N/A	SELF RECORDED TAPES ARE NOISY - OLD VIDEO CAN BE SEEN IN NOISE BARS	CHECK/REPLACE Q16 (P/N# 2SA1577(Q,R) ) IN THE FLYING ERASE HEAD CIRCUIT
JVC	GRAX17U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GRAX220U	N/A	WILL NOT ERASE OLD AUDIO	CHECK/REPLACE C2026 (P/N3 NDC31HJ-471X)
JVC	GRAX25U	N/A	UNIT DISPLAYS THE LETTER 'A' ACROSS THE BOTTOM OF SCREEN	CHECK/REPLACE IC302 (P/N# BU5946AFS-X)
JVC	GRAX25U	N/A	CAMERAS VIDEO OUTPUT HAS SYNC BUT NO VIDEO INFORMATION	CHECK/REPLACE IC1 (P/N# MN3111H) ON CCD BOARD
JVC	GRAX25U	N/A	VIDEO FROM THE CAMERA IS BLACK AND WHITE - NO COLOR	CHECK/REPLACE IC10 (P/N# EHDG1450)
JVC	GRAX25U	N/A	INTERMITTENTLY STARTS TO PLAYBACK VERY FAST AND E03 SHOWS UP IN VIEWFINDER	CHECK/REPLACE C203 (P/N# QCF81CZ-225)
JVC	GRAX2U	N/A	PICTURE FADES TO BLACK IN THE MONITOR MODE	CHECK/REPLACE IC501 (P/N# BH7511K1) ON THE DECK CIRCUIT BD.
JVC	GRAX2U	N/A	OSD DISPLAY FLICKERS	CHECK/REPLACE IC301 (P/N# M37460M8-067FP)
JVC	GRAX2U	N/A	VERTICAL BARS IN THE CAMERA VIDEO	CHECK/RESOLDER CCD DIRECTLY TO IT'S SOCKET
JVC	GRAX2U	N/A	INTERMITTENT ' DEW' INDICATOR IN VIEWFINDER	CHECK/RESOLDER WIRES FROM DEW SENSOR DIRECTLY TO PCB
JVC	GRAX2U	N/A	NO COLOR ON CAMERA	CHECK/REPLACE IC8 (TC7S04F) ON SSG/VIDEO PCB
JVC	GRAX30U	N/A	TAPE RUNS TOO FAST IN THE PLAY MODE	CHECK/REPLACE X1 (P/N# YU40141)
JVC	GRAX33U	N/A	NO COLOR IN CAMERA PIX	CHECK/REPLACE IC208 (P/N # EHDGA1450)
JVC	GRAX404U	N/A	E-E PICTURE FROM CAMERA IS MOSTLY RED	CHECK/REPLACE Q806 (P/N# 2SC4617(QR) )
JVC	GRAX50U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GRAX55U	N/A	NO PICTURE IN E-E MODE	CHECK/REPLACE IC16 (P/N# UPD78238GC-228) ON PROCESS BOARD
JVC	GRAX5GYU	N/A	NO PICTURE FROM CAMERA IN THE MONITOR MODE	CHECK/REPLACE IC1 (P/N# MN5180) ON THE SSG BOARD
JVC	GRAX5U	N/A	INTERMITTENT ' DEW' INDICATOR IN VIEWFINDER	CHECK/RESOLDER WIRES FROM DEW SENSOR DIRECTLY TO PCB
JVC	GRAX5U	N/A	NO LUMINANCE FROM CAMERA	CHECK/REPLACE IC4 (P/N# MSM6834MS) ON SSG BOARD
JVC	GRAX5U	N/A	DRUM SPINS VERY FAST THEN GOES TO STOP MODE - E04 IS DISPLAYED IN THE VIEWFINDER	CHECK/REPLACE C204 (P/N# NEH11HM-474NZ)
JVC	GRAX5U	N/A	VERTICAL BARS IN THE CAMERA VIDEO	CHECK/RESOLDER CCD DIRECTLY TO IT'S SOCKET
JVC	GRAX7	N/A	DEW INDICATOR STAYS ON WITH NO PRESENCE OF MOISTURE	REMOVE BATTERY AND LITHIUM BATTERY FOR 10-15 SECONDS AND THEN RE-INSTALL
JVC	GRAX7BKU	N/A	WILL NOT EJECT CASSETTE	CHECK/ADJUST MODE SELECT SWITCH FOR PROPER ALIGNMENT
JVC	GRAX7GYU	N/A	DISTORTED AND LOW AUDIO IN THE RECORD MODE	CHECK/REPLACE AUDIO/CONTROL HEAD (P/N # YQ41871A-3)
JVC	GRAX7U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GRAX7U	N/A	PLAYBACK PICTURE HAS A BIG HORZ. BAR OF NOISE THAT APPEARS RANDOMLY IN THE PICTURE	CHECK/REPLACE C266 (P/N# NEH11HM-105NZ)
JVC	GRAX7U	N/A	POOR RECORDED VIDEO - VIDEO FLASHES DURING PLAYBACK	CHECK/REPLACE DC-DC CONVERTER (YU41714)
JVC	GRAX7U	N/A	VERTICAL BARS IN THE CAMERA VIDEO	CHECK/RESOLDER CCD DIRECTLY TO IT'S SOCKET
JVC	GRAX7U	N/A	WILL NOT RECORD VIDEO	CHECK/REPLACE R659 ( FM LEVEL CTRL )
JVC	GRAX7U	N/A	UNIT STAYS IN THE PLAYBACK MODE - WILL NOT GO INTO THE RECORD MODE	CHECK/REPLACE DD1 (P/N# PEAS2033)
JVC	GRAX7U	N/A	NO RECORD VIDEO	CHECK/RESOLDER CONNECTIONS ON R659 ON Y/C BOARD
JVC	GRAX7U	N/A	INTERMITTENT ' DEW' INDICATOR IN VIEWFINDER	CHECK/RESOLDER WIRES FROM DEW SENSOR DIRECTLY TO PCB
JVC	GRAX7U	N/A	DEW INDICATOR IS ALWAYS ACTIVE	CHECK/RESOLDER CONNECTIONS ON CN16
JVC	GRAX800U	N/A	UNIT TAKES 12 SECONDS TO SHUT OFF WHEN POWER IS TURNED OFF	CHECK/REPLACE OPTICAL BLOCK (P/N# YU30787-1-1)
JVC	GRAX808U	N/A	NO E-E PICTURE	CHECK/REPLACE IC911 (P/N# UPD78054GC-016)
JVC	GRAX808U	N/A	E-E PICTURE INTERMITTENTLY HAS NO RED	CHECK/REPLACE IC801 (P/N# AN2145NFHP)
JVC	GRAX808U	N/A	NO PICTURE IN THE VIEWFINDER	CHECK/REPLACE C109 (P/N# NEE21DM-226RZ)
JVC	GRAXM40U	N/A	NO PICTURE IN THE EVF - LCD MONITOR PICTURE UPSIDE DOWN	CHECK/REPLACE SW7501 (P/N# NSW0007-001X)
JVC	GRAXM40U	N/A	NO PICTURE ON LCD MONITOR	CHECK/REPLACE T7501 (P/N3 NQS0010-001)
JVC	GRC7U	N/A	NO E-E VIDEO	CHECK/REPLACE LPF2 (P/N # PU58956) ON THE VIDEO BOARD
JVC	GRC7U	N/A	POOR VIDEO ON RECORDED PIX AND NOISY - NO TRACKING CONTROL IN THE PLAYBACK MODE.	CHECK/REPLACE C6 ON THE OPERATION BOARD
JVC	GRDV1U	N/A	BLUE SCREEN DURING REVERSE SLOW MOTION	CHECK/REPLACE R697 (P/N3 NRSA6AJ-154AW (150k? )
JVC	GREZ1U	N/A	OLD AUDIO IS NOT ERASED ON NEW RECORDINGS	CHECK/REPLACE L401 (P/N# PELN0755)
JVC	GRM3U	N/A	STOPS DURING PLAYBACK	CHECK/REPLACE IC301 (P/N# UPD78P148GF-A01)
JVC	GRM4U	N/A	WON'T ERASE OLD AUDIO AND WILL NOT RECORD NEW AUDIO - PRE-RECORDED TAPES PLAY OK	CHECK/REPLACE L401 (P/N# YU41135-101K)
JVC	GRM4U	N/A	WILL NOT EJECT	CHECK/REPLACE END SENSOR (P/N# YQ42431A-4)
JVC	GRM4U	N/A	DOES NOT ERASE AUDIO	CHECK/REPLACE L404 (P/N # YU41135-101K)
JVC	GRM4U	N/A	AFTER POWERING ON THE UNIT, IT WOULD SHUT DOWN AFTER A FEW SECONDS	CHECK/REPLACE R311 (P/N# NRVA62D-623N)
JVC	GRM5U	N/A	STOPS DURING PLAYBACK	CHECK/REPLACE IC301 (P/N# UPD78P148GF-A01)
JVC	GRM5U	N/A	WHITE HORZ. LINES IN THE CAMERA PIX	CHECK/REPLACE C45 ON CCD BOARD
JVC	GRM5U	N/A	UNIT POWERS UP BUT NO OTHER FUNCTIONS WORK - MECHANISM IS JAMMED	CHECK/REPLACE MIDDLE POLE CAM GEAR (REF#19)(P/N# YQ31323-1)
JVC	GRM7U	N/A	STOPS DURING PLAYBACK	CHECK/REPLACE IC301 (P/N# UPD78P148GF-A04)
JVC	GRSV3U	N/A	RECORDED PICTURE IS ORANGE IN COLOR	CHECK/REPLACE IC802 (P/N# MN3860SA-X)
JVC	GRSX90U	N/A	DEW WARNING DISPLAYED IN THE VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON PLUG CN16 DIRECTLY TO BOARD- - NORMAL DEW SENSOR RESISTANCE IS 500 TO 3k
JVC	GRSZ7U	N/A	WILL NOT AUTO-FOCUS	CHECK/REPLACE IC503 (P/N# SPC17A85ZVM-X)
JVC	GYX2U	N/A	ON POWER, THERE IS NO VIDEO PRODUCED	CHECK/REPLACE L2 (P/N# SCV0983-500) ON PS BOARD
JVC	KY27U	N/A	SYNC SIGNAL GENERATOR DOESN'T FUNCTION AFTER WARM	CHECK/REPLACE IC10 (P/N# JCS0002) ON THE 'SE' BOARD
JVC	KYF55U	N/A	LOW VIDEO OUTPUT IN THE CAMERA MODE	CHECK/REPLACE R525 (P/N# NRVA63D-4720
JVC	TK1280U	N/A	CAMERA HAS NO VIDEO - ONLY VERTICAL LINES	CHECK/REPLACE Q51 (P/N# 2SB1218(Q,R) ) ON CDS/TG BOARD
JVC	TKC600U	N/A	VIDEO OUTPUT LEVEL IS LOW WITH IRIS FULLY OPEN	CHECK/REPLACE Q402 (P/N# 2SD1819A(RS) )
MAGNAVOX	CVJ310	N/A	CHARGER IS DEAD - NO POWER LIGHTS	CHECK/REPLACE C13 FOR SHORT
MAGNAVOX	CVN320	N/A	UNIT WILL NOT GO INTO VCR MODE - VCR FUNCTION BUTTONS HAVE TO BE CONTINUALLY PRESSED TO OPERATE THAT FUNCTION	CHECK/REPLACE TV/VCR SWITCH (P/N# 483527617176)
MAGNAVOX	CVR315	N/A	INTERMITTENT BATTERY OPERATION	INSTALL KIT (P/N# 483531057299)
MAGNAVOX	CVR315	N/A	INTERMITTENT PROBLEM - BATTERY DOES NOT ALWAYS CHARGE OR OPERATE THE CAMCORDER AS LONG AS IT SHOULD	CHECK CONTACTS ON BATTERY FOR POSSIBLY BEING DEFORMED
MAGNAVOX	CVS315	N/A	INTERMITTENT PROBLEM - BATTERY DOES NOT ALWAYS CHARGE OR OPERATE THE CAMCORDER AS LONG AS IT SHOULD	CHECK CONTACTS ON BATTERY FOR POSSIBLY BEING DEFORMED
MAGNAVOX	CVT325	N/A	INTERMITTENT PROBLEM - BATTERY DOES NOT ALWAYS CHARGE OR OPERATE THE CAMCORDER AS LONG AS IT SHOULD	CHECK CONTACTS ON BATTERY FOR POSSIBLY BEING DEFORMED
MAGNAVOX	V80088BK01	N/A	CHARGER IS DEAD - NO POWER LIGHTS	CHECK/REPLACE C13 FOR SHORT
MAGNAVOX	VR8209	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
MAGNAVOX	VR8209	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
MAGNAVOX	VR8209	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
MAGNAVOX	VR8209	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
MAGNAVOX	VR8209	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
MAGNAVOX	VR8209	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
MAGNAVOX	VR9143	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
MAGNAVOX	VR9143	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
MAGNAVOX	VR9143	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
MAGNAVOX	VR9143	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
MAGNAVOX	VR9143	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
MAGNAVOX	VR9143	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
MAGNAVOX	VR9143	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
MEMOREX	SM2000	N/A	SAME AS REALISTIC MODEL 150 OR CAT.# 16-851
NEC	V10	N/A	INTERM. LIT POW/CHARG. LEDS	REPLACE D1006
PANASONIC	PV300D	N/A	DEAD-WILL NOT POWER UP	CHECK/REPLACE Q1001,IC1001 AND IC1002
PANASONIC	PV300D	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
PANASONIC	PV320D	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
PANASONIC	PV320D	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
PANASONIC	PV320D	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
PANASONIC	PV320D	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
PANASONIC	PV320D	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
PANASONIC	PV320D	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
QUASAR	VM23	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
QUASAR	VM23	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
QUASAR	VM23	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
QUASAR	VM23	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
QUASAR	VM23	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
QUASAR	VM23	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
RCA	CC174	N/A	INTERNAL CLOCK MAY BE OFF UNDER CERTAIN VARIOUS BATTERY AND STORAGE CONDITIONS	CHANGE C43 TO A 0.47uF (P/N# 222932)
RCA	CC174	N/A	CLOCK DOESN'T KEEP ACCURATE TIME	CHANGE C43 FROM A 2.2uF @ 16v TO 0.47uF (P/N# 222932)
RCA	CC174	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC174	N/A	CASSETTE HOUSING IS HARD TO CLOSE AND LOCK	CHECK/REPLACE HOUSING ASSY. REF# 138 WITH (P/N# 219283)
RCA	CC176	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC176	N/A	INTERNAL CLOCK MAY BE OFF UNDER CERTAIN VARIOUS BATTERY AND STORAGE CONDITIONS	CHANGE C43 TO A 0.47uF (P/N# 222932)
RCA	CC176	N/A	CASSETTE HOUSING IS HARD TO CLOSE AND LOCK	CHECK/REPLACE HOUSING ASSY. REF# 138 WITH (P/N# 219283)
RCA	CC176	N/A	CLOCK DOESN'T KEEP ACCURATE TIME	CHANGE C43 FROM A 2.2uF @ 16v TO 0.47uF (P/N# 222932)
RCA	CC177	N/A	TAKE UP LOAD POST MAY CHATTER OR NOT SEAT PROPERLY WHEN USED ON SLP(EP) SPEED	CHECK/REPLACE LOAD POST BASE ASSY. (P/N# 214447)
RCA	CC177	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC177	N/A	STOPS WHILE PLAYING BACK SLP RECORDED TAPES	CHECK/REPLACE IC301 (P/N# 217037)
RCA	CC177	N/A	SHUTS DOWN INTERMITTENTLY DURING EP PLAYBACK MODE	CHECK/REPLACE IC301 (P/N# 217037)
RCA	CC178	N/A	INTERNAL CLOCK MAY BE OFF UNDER CERTAIN VARIOUS BATTERY AND STORAGE CONDITIONS	CHANGE C43 TO A 0.47uF (P/N# 222932)
RCA	CC178	N/A	CLOCK DOESN'T KEEP ACCURATE TIME	CHANGE C43 FROM A 2.2uF @ 16v TO 0.47uF (P/N# 222932)
RCA	CC180	N/A	E03 IN VIEWFINDER AND BREAKING OF THE MIDDLE POST AND/OR EATING OF TAPES	INSTALL KIT (P/N# 215178)
RCA	CC180	N/A	CAMERA VIDEO CUTS OUT AFTER WARM	CHECK/REPLACE X1 ON 'SSG' BOARD
RCA	CC180	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC187	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC188	N/A	INTERNAL CLOCK MAY BE OFF UNDER CERTAIN VARIOUS BATTERY AND STORAGE CONDITIONS	CHANGE C43 TO A 0.47uF (P/N# 222932)
RCA	CC188	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC188	N/A	CLOCK DOESN'T KEEP ACCURATE TIME	CHANGE C43 FROM A 2.2uF @ 16v TO 0.47uF (P/N# 222932)
RCA	CC190	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	CC250	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CC275	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CC286	N/A	CYLINDER WILL NOT RUN AFTER 2 MINUTES OF OPERATION	CHECK/REPLACE IC906
RCA	CC300	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CC300	N/A	CAMERA PICTURE IS RED WITH LITTLE VIDEO	CHECK/RESOLDER TRACE BETWEEN CN002 PIN #1 AND IC005 PIN #33
RCA	CC320	N/A	TEARING IN THE PICTURE AROUND OUTLINE OF OBJECTS	CHECK/REPLACE IC581
RCA	CC350	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CC350	N/A	APPROX. 30Hz. OSCILLATION WHEN AZC IS AT MAXIMUM	CHECK/REPLACE C402 OR CONNECTIONS
RCA	CC390	N/A	NO PICTURE IN VIEWFINDER	CHECK FOR OPEN TRACE BETWEEN T801 PIN #5 AND R302
RCA	CC391	N/A	WON'T EJECT TAPE	CHECK/REPLACE QF901 CIRCUIT PROTECTOR
RCA	CC405	N/A	APPEARS TO HAVE A BAD UPPER DRUM BUT STOPPING AND RESTARTING WILL CHANGE SYMPTOMS	CHECK/RESOLDER CONNECTIONS ON PIN #2 OF IC601
RCA	CC406	N/A	WON'T EJECT TAPE	CHECK/REPLACE QF901 CIRCUIT PROTECTOR
RCA	CC414	N/A	MAIN FUSE BLOWN FOR NO APPARENT REASON	THE CRIMP ON THE RCA CONNECTORS ALLOW JACK TO MOVE AND SHORT OUT THE 5 VOLT LINE - TIGHTEN JACK AND INSULATE
RCA	CC415	N/A	INTERMITTENT VIDEO IN CAMERA SECTION	CHECK/RESOLDER CONNECTIONS ON X101
RCA	CC415	N/A	DEAD - NO ATTEMPT TO POWER UP	CHECK/REPLACE S901 (P/N# 215500)
RCA	CC417	N/A	MAIN FUSE BLOWN FOR NO APPARENT REASON	THE CRIMP ON THE RCA CONNECTORS ALLOW JACK TO MOVE AND SHORT OUT THE 5 VOLT LINE - TIGHTEN JACK AND INSULATE
RCA	CC420	N/A	MAIN FUSE BLOWN FOR NO APPARENT REASON	THE CRIMP ON THE RCA CONNECTORS ALLOW JACK TO MOVE AND SHORT OUT THE 5 VOLT LINE - TIGHTEN JACK AND INSULATE
RCA	CC422	N/A	MAIN FUSE BLOWN FOR NO APPARENT REASON	THE CRIMP ON THE RCA CONNECTORS ALLOW JACK TO MOVE AND SHORT OUT THE 5 VOLT LINE - TIGHTEN JACK AND INSULATE
RCA	CC423	N/A	MAIN FUSE BLOWN FOR NO APPARENT REASON	THE CRIMP ON THE RCA CONNECTORS ALLOW JACK TO MOVE AND SHORT OUT THE 5 VOLT LINE - TIGHTEN JACK AND INSULATE
RCA	CC445	N/A	DEAD - WILL NOT TURN ON OR EJECT	REMOVE BATTERY AND 3 VOLT LITHIUM BATTERY,WAIT 10 MINUTES, THEN INSTALL 3 VOLT LITHIUM BATTERY FIRST,THEN APPLY POWER.
RCA	CC512	N/A	DEAD - WILL NOT TURN ON OR EJECT	REMOVE BATTERY AND 3 VOLT LITHIUM BATTERY,WAIT 10 MINUTES, THEN INSTALL 3 VOLT LITHIUM BATTERY FIRST,THEN APPLY POWER.
RCA	CC525	N/A	DEAD	CHECK/REPLACE CX902 CRYSTAL
RCA	CC525	N/A	DEAD - WILL NOT TURN ON OR EJECT	REMOVE BATTERY AND 3 VOLT LITHIUM BATTERY,WAIT 10 MINUTES, THEN INSTALL 3 VOLT LITHIUM BATTERY FIRST,THEN APPLY POWER.
RCA	CC600	N/A	UNDER CERTAIN LOW VOLTAGE CONDITIONS , THE CAMCORDER MAY SHUT OFF AND NOT ALLOW THE TAPE TO BE EJECTED	CHANGE R14 TO 100?(P/N# 200300)
RCA	CC600	N/A	EXTREMELY DIFFICULT TO PERFORM 'COLOR DIFFERENCE SIGNAL' ADJUSTMENT	CHECK/REPLACE RA813 (P/N# 223499)
RCA	CC603	N/A	UNDER CERTAIN LOW VOLTAGE CONDITIONS , THE CAMCORDER MAY SHUT OFF AND NOT ALLOW THE TAPE TO BE EJECTED	CHANGE R14 TO 100?(P/N# 200300)
RCA	CC603	N/A	EXTREMELY DIFFICULT TO PERFORM 'COLOR DIFFERENCE SIGNAL' ADJUSTMENT	CHECK/REPLACE RA813 (P/N# 223499)
RCA	CC604	N/A	UNDER CERTAIN LOW VOLTAGE CONDITIONS , THE CAMCORDER MAY SHUT OFF AND NOT ALLOW THE TAPE TO BE EJECTED	CHANGE R14 TO 100?(P/N# 200300)
RCA	CC604	N/A	WHILE RECORDING A SLIGHT BEAT PATTERN OR NOISE MAY BE OBSERVED IN THE VIEWFINDER	CHANGE C201 TO 10uF (P/N# 168469)
RCA	CC604	N/A	EXTREMELY DIFFICULT TO PERFORM 'COLOR DIFFERENCE SIGNAL' ADJUSTMENT	CHECK/REPLACE RA813 (P/N# 223499)
RCA	CC604	N/A	INTERFERENCE VISIBLE IN THE VIEWFINDER PICTURE IN BOTH CAMERA OR VCR MODES	CHECK/REPLACE WIRING HARNESS IN VIEWFINDER WITH NEW TYPE (P/N# 226299)
RCA	CC710	N/A	SLIGHT VIDEO JITTER OR INSTABILITY IN PICTURE	CHECK/REPLACE BOAT STOPPER WITH NEW TYPE (P/N# 226294)
RCA	CC740	N/A	VIDEO DISPLAY IN EVF IS NOT STABLE	ADD 1uF @ 35v (P/N# 158951) FROM COLLECTOR OF Q902 TO GROUND
RCA	CC800	N/A	UNDER CERTAIN LOW VOLTAGE CONDITIONS , THE CAMCORDER MAY SHUT OFF AND NOT ALLOW THE TAPE TO BE EJECTED	CHANGE R14 TO 100?(P/N# 200300)
RCA	CC800	N/A	EXTREMELY DIFFICULT TO PERFORM 'COLOR DIFFERENCE SIGNAL' ADJUSTMENT	CHECK/REPLACE RA813 (P/N# 223499)
RCA	CLR200	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CMR200	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CMR300	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CPR250	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CPR300	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	CPR350	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
RCA	PRO422	N/A	WHEN UNIT IS PLAYING, IT DOESN'T STOP AS SOON AS THE STOP BUTTON IS PRESSED RESULTING IN POOR EDITTING	CHECK/REPLACE IC351 (P/N# 231553)
RCA	PRO807	N/A	ERRATIC SPEED IN RECORD OR PLAYBACK	CHECK/REPLACE IC361 (P/N# 213100)
RCA	PRO807	N/A	BATTERY CONTACTS WEAK OR BROKEN	CHECK/REPLACE BATTERY HOLDER CONTACTS (P/N# 216783)
RCA	PRO808	N/A	NO CAPSTAN MOVEMENT	ADD METAL STOPPER (P/N# 217439) AND SCREW (P/N# 217433) AND CHANGE TAPE STOPPER (P/N# 217437)
RCA	PRO820	N/A	NO VIDEO - BLANK RASTER - NO OSD BUT AUDIO IS OK	CHECK/RESOLDER CONNECTIONS ON IC753 PINS 11 & 13 TO GROUND
RCA	PRO820	N/A	WILL GO FROM PLAY TO RECORD AND BACK TO PLAY AND UNIT WAS SET TO VCR MODE	CHECK/RESOLDER CONNECTIONS ON X1861
RCA	PRO830	N/A	INTERMITTENT LOSS OF SERVO LOCK	REPLACE C3824 WITH A 0 CHIP RESISTOR (P/N# 213223)
RCA	PRO830	N/A	NO CAPSTAN MOVEMENT	ADD METAL STOPPER (P/N# 217439) AND SCREW (P/N# 217433) AND CHANGE TAPE STOPPER (P/N# 217437)
RCA	PRO840	N/A	INTERMITTENT LOSS OF SERVO LOCK	REPLACE C3824 WITH A 0 CHIP RESISTOR (P/N# 213223)
RCA	PRO843	N/A	DEAD OR NO VIDEO IN THE VIEWFINDER OR AT THE VIDEO JACKS	CHECK/RESOLDER CONNECTIONS ON CN501 AND CN502
RCA	PRO844	N/A	RECHARGEABLE BATTERY CONTACTS BENT OR BROKEN	CHECK/REPLACE BATTERY CASE ASSY. (P/N# 230005)
RCA	PRO846	N/A	RECHARGEABLE BATTERY CONTACTS BENT OR BROKEN	CHECK/REPLACE BATTERY CASE ASSY. (P/N# 230005)
RCA	PRO860	N/A	WHISTLE OR TONE NOISE BEING PICKUP BY MICROPHONE	USE (P/N# 215563) TO REMOVE RING ON TOP OF DRUM AND REPLACE STATOR ASSY. WITH (P/N# 215562)
RCA	PRO860	N/A	INTERMITTENT OSD OR NO OSD	CHECK/RESOLDER CONNECTIONS ON IC906
RCA	PRO860	N/A	SLOW TAPE LOADING OR UNLOADING	CHECK/REPLACE REGULATOR BLOCK ASSEMBLY (#122)
RCA	PRO865	N/A	WHISTLE OR TONE NOISE BEING PICKUP BY MICROPHONE	USE (P/N# 215563) TO REMOVE RING ON TOP OF DRUM AND REPLACE STATOR ASSY. WITH (P/N# 215562)
RCA	PRO870	N/A	LINES IN RECORDING AND EVF - EVF MAY WHITE OUT - ZOOM EFFECTS SEVERITY OF PROBLEM	CHECK/RESOLDER CONNECTIONS ON IC1208
RCA	PRO883	N/A	DEW APPEARS IN THE VIEWFINDER - ALL TAPE FUNCTIONS INOPER.	HARD WIRE PLUG PG902
RCA	PRO884HB	N/A	RECHARGEABLE BATTERY CONTACTS BENT OR BROKEN	CHECK/REPLACE BATTERY CASE ASSY. (P/N# 230005)
RCA	PRO930	N/A	DEW APPEARS IN THE VIEWFINDER - ALL TAPE FUNCTIONS INOPER.	HARD WIRE PLUG PG902
RCA	PRO932	N/A	RECHARGEABLE BATTERY CONTACTS BENT OR BROKEN	CHECK/REPLACE BATTERY CASE ASSY. (P/N# 230005)
RCA	PRO942	N/A	RECHARGEABLE BATTERY CONTACTS BENT OR BROKEN	CHECK/REPLACE BATTERY CASE ASSY. (P/N# 230005)
RCA	PSC10	N/A	DEW APPEARS IN THE VIEWFINDER - ALL TAPE FUNCTIONS INOPER.	HARD WIRE PLUG PG902
RCA	PSC15C	N/A	STREAKY OR NO VIDEO	CHECK/REPLACE CCD SOCKET (P/N# 215818)
RCA	PSC20	N/A	DEW APPEARS IN THE VIEWFINDER - ALL TAPE FUNCTIONS INOPER.	HARD WIRE PLUG PG902
RCA	PSC24C	N/A	VIDEO DISPLAY IN EVF IS NOT STABLE	ADD 1uF @ 35v (P/N# 158951) FROM COLLECTOR OF Q902 TO GROUND
RCA	PSC24C	N/A	SLIGHT VIDEO JITTER OR INSTABILITY IN PICTURE	CHECK/REPLACE BOAT STOPPER WITH NEW TYPE (P/N# 226294)
SAMSUNG	SCF30	N/A	DEAD - NO POWER CHECK FOR LOW ON PINS #5 OR #8 OF IC603-IF LOW, REPL. PART	CHECK/REPLACE IC603 (P/N# AC14-12012F)
SAMSUNG	SCF32	N/A	DEAD - NO POWER CHECK FOR LOW ON PINS #5 OR #8 OF IC603-IF LOW, REPL. PART	CHECK/REPLACE IC603 (P/N# AC14-12012F)
SAMSUNG	SCF34	N/A	DEAD - NO POWER CHECK FOR LOW ON PINS #5 OR #8 OF IC603-IF LOW, REPL. PART	CHECK/REPLACE IC603 (P/N# AC14-12012F)
SAMSUNG	SCF35	N/A	DEAD - NO POWER CHECK FOR LOW ON PINS #5 OR #8 OF IC603-IF LOW, REPL. PART	CHECK/REPLACE IC603 (P/N# AC14-12012F)
SAMSUNG	SCF500	N/A	CAPSTAN SPEED SEARCHES OR HUNTS	CHECK/REPLACE CAPSTAN BELT FOR SLIPPAGE
SAMSUNG	SCF500	N/A	IN RECORD PAUSE, THE CAPSTAN ALWAYS RUNS	CHECK/REPLACE R235 AND R236 IN THE POWER SUPPLY
SAMSUNG	SCF500	N/A	CAPSTAN ALWAYS RUNS IN RECORD PAUSE	CHECK/REPLACE R235 AND R236
SAMSUNG	SCF501	N/A	OSD CHARACTERS ARE SMEARED	CHECK/REPLACE IC551
SAMSUNG	SCF501	N/A	OSD IS SMEARED	CHECK/REPLACE IC551
SAMSUNG	SCF501	N/A	NEGATIVE VIDEO FROM CAMERA SECTION	CHECK/REPLACE VR212 FOR OPEN
SAMSUNG	SCF700	N/A	RECORDS NEGATIVE IMAGE	CHECK/RESOLDER CONNECTIONS ON C219 AND FULL ERASE HEADS
SAMSUNG	SCX800	N/A	INTERMITTENT OSD ERROR - NO OSD - WRONG DISPLAY OR OUT OF SYNC DISPLAY	CHECK/REPLACE FUNCTION/DIGITAL/SWITCH CIRCUIT BOARD CALL 1-800-833-6616 TO RECEIVE BOARD
SEARS	93453720550	N/A	WON'T REWIND AND DIM LCD	CHECK/REPLACE C911
SEARS	93453730651	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
SEARS	93453741750	N/A	WILL NOT RECORD OR PLAYBACK AND DRUM MOTOR SPEED MAY ACCELERATE.	CHECK/CLEAN CONNECTIONS ON RIBBON CABLE (PG613)
SEARS	93453742850	N/A	SHUTS OFF IN RECORD AND PLAYBACK	CHECK/RESOLDER CONNECTIONS ON RIBBON CONNECTORS PG613 AND PG201
SEARS	93453746950	N/A	EXTERNAL LIGHT WON'T WORK ON AC BUT DOES WORK ON BATTERY	CHECK/REPLACE Q925,D908,R887,F902,F903
SHARP	VLC73UA	N/A	WILL NOT POWER UP (AC OR DC)-OR SHUTS DOWN WITHIN A FEW SECONDS.	CHECK C927 AND C936 FOR ELECTROLYTE LEAKING,Q914 AND F901--EXAMINE CIRCUIT FOIL NEAR LEAKAGE FOR OPENS.
SHARP	VLC73UA	N/A	BACK LIGHT COMPENSATION HAS NO EFFECT	IF R863 IS A 22k REPLACE IT WITH A 3.3k
SHARP	VLC77UA	N/A	BACK LIGHT COMPENSATION HAS NO EFFECT	IF R863 IS A 22k REPLACE IT WITH A 3.3k
SHARP	VLC77UA	N/A	WILL NOT POWER UP (AC OR DC)-OR SHUTS DOWN WITHIN A FEW SECONDS.	CHECK C927 AND C936 FOR ELECTROLYTE LEAKING,Q914 AND F901--EXAMINE CIRCUIT FOIL NEAR LEAKAGE FOR OPENS.
SHARP	VLE30E	N/A	EJECTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	TRY REMOVING LITHIUM BATTERY AND LET SIT FOR SEVERAL MINUTES, THEN RE-INSTALL AND SET CLOCK
SHARP	VLE34U	N/A	UNIT GOES INTO TAPE PROTECTION MODE - BATTERY AND DEW/CLOG LEDS FLASH SIMULTANEOUSLY	CHECK/RESOLDER CONNECTIONS ON P330 - ALSO CHECK THE TORQUE ON THE TAKE-UP SPOOL
SHARP	VLE39U	N/A	UNIT GOES INTO TAPE PROTECTION MODE - BATTERY AND DEW/CLOG LEDS FLASH SIMULTANEOUSLY	CHECK/RESOLDER CONNECTIONS ON P330 - ALSO CHECK THE TORQUE ON THE TAKE-UP SPOOL
SHARP	VLE46U	N/A	UNIT GOES INTO TAPE PROTECTION MODE - BATTERY AND DEW/CLOG LEDS FLASH SIMULTANEOUSLY	CHECK/RESOLDER CONNECTIONS ON P330 - ALSO CHECK THE TORQUE ON THE TAKE-UP SPOOL
SHARP	VLE49U	N/A	UNIT GOES INTO TAPE PROTECTION MODE - BATTERY AND DEW/CLOG LEDS FLASH SIMULTANEOUSLY	CHECK/RESOLDER CONNECTIONS ON P330 - ALSO CHECK THE TORQUE ON THE TAKE-UP SPOOL
SHARP	VLL150	N/A	DEAD - TRIES TO COME ON FOR 1 SECOND THEN SHUTS OFF - MISSING 5v AND 12v	CHECK/REPAIR OPEN TRACE (FEEDTHRU) BETWEEN IC901 PIN#10 AND R912
SHARP	VLL150U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL150U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL170U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL170U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL175	N/A	DEAD - TRIES TO COME ON FOR 1 SECOND THEN SHUTS OFF - MISSING 5v AND 12v	CHECK/REPAIR OPEN TRACE (FEEDTHRU) BETWEEN IC901 PIN#10 AND R912
SHARP	VLL175U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL175U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL210U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL210U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL250	N/A	DEAD - TRIES TO COME ON FOR 1 SECOND THEN SHUTS OFF - MISSING 5v AND 12v	CHECK/REPAIR OPEN TRACE (FEEDTHRU) BETWEEN IC901 PIN#10 AND R912
SHARP	VLL250U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL250U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL250U	N/A	MAKES SQUEALING NOISE IN PLAYBACK OR RECORD	CHECK/REPOSITION THE GROUNDING BRUSH ON THE BOTTOM OF THE DRUM MOTOR.
SHARP	VLL250U	N/A	WILL NOT POWER UP AND NO LOADING	CHECK/REPLACE IC701
SHARP	VLL270U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL270U	N/A	NO AUTO-FOCUS,ZOOM OR CAMERA VIDEO	CHECK/REPLACE SSG BOARD (DUNTK2138PM01)
SHARP	VLL270U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL280U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL280U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL285U	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL285U	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL30	N/A	FOCUS MOTOR WILL NOT RUN	CHECK FOR OPEN FEED-THRU LOCATED BETWEEN Q509 BASE AND Q510 PIN #4 COLLECTOR
SHARP	VLL310U	N/A	DEAD - NO ATTEMPT TO TURN ON	CHECK/REPLACE Q920 AND Q940 (P/N# VS2SA1213Y/-1)
SHARP	VLL310U	N/A	EXCESSIVE HORZ. DEFLECTION IN THE VIEWFINDER (OVERSCANNING)	CHANGE R718 TO 560 ohms AND R745 TO 2.2 ohms
SHARP	VLL315	N/A	DEAD - TRIES TO COME ON FOR 1 SECOND THEN SHUTS OFF - MISSING 5v AND 12v	CHECK/REPAIR OPEN TRACE (FEEDTHRU) BETWEEN IC901 PIN#10 AND R912
SHARP	VLL315U	N/A	DEAD - NO ATTEMPT TO TURN ON	CHECK/REPLACE Q920 AND Q940 (P/N# VS2SA1213Y/-1)
SHARP	VLL315U	N/A	EXCESSIVE HORZ. DEFLECTION IN THE VIEWFINDER (OVERSCANNING)	CHANGE R718 TO 560 ohms AND R745 TO 2.2 ohms
SHARP	VLL330U	N/A	LINES IN THE PICTURE ON CAMERA VIDEO ESPECIALLY WHEN USING AUTO-FOCUS OR ZOOM	CHECK/REPLACE C904 (47uF @ 6.3v)
SHARP	VLL50	N/A	FOCUS MOTOR WILL NOT RUN	CHECK FOR OPEN FEED-THRU LOCATED BETWEEN Q509 BASE AND Q510 PIN #4 COLLECTOR
SHARP	VLL50U	N/A	POOR VIDEO THROUGH THE CAMERA SECTION	CHECK/REPLACE FILTERS FB2 AND FB3 IN THE SSG CIRCUIT ON THE MAIN PWB. ORDER KIT # BQC-VLL50U/-1
SHARP	VLL510U	N/A	EXCESSIVE HORZ. DEFLECTION IN THE VIEWFINDER (OVERSCANNING)	CHANGE R718 TO 560 ohms AND R745 TO 2.2 ohms
SHARP	VLL80UA	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL80UA	N/A	MAKES SQUEALING NOISE IN PLAYBACK OR RECORD	CHECK/REPOSITION THE GROUNDING BRUSH ON THE BOTTOM OF THE DRUM MOTOR.
SHARP	VLL80UA	N/A	DEAD - TRIES TO COME ON FOR 1 SECOND THEN SHUTS OFF - MISSING 5v AND 12v	CHECK/REPAIR OPEN TRACE (FEEDTHRU) BETWEEN IC901 PIN#10 AND R912
SHARP	VLL80UA	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL80UB	N/A	NO POWER	CHECK/REPLACE POWER ON/OFF SWITCH,F901,Q902,T902,D919,Q904, C927,C936,IC901,Q915,C925,C941,C942 AND C946 IN SOME MODELS
SHARP	VLL80UB	N/A	INTERMITTENT LOSE OF HORZ. DEFLECTION IN VIEW FINDER	CHECK L702 FOR BROKEN WIRE OR CONNECTIONS
SHARP	VLL80UB	N/A	DEAD - TRIES TO COME ON FOR 1 SECOND THEN SHUTS OFF - MISSING 5v AND 12v	CHECK/REPAIR OPEN TRACE (FEEDTHRU) BETWEEN IC901 PIN#10 AND R912
SHARP	VLM6U	N/A	IRIS REPEATEDLY OPENS AND CLOSES PRODUCING A CHATTERING NOISE	CHECK/RESOLDER CONNECTIONS ON 26 PIN CONNECTOR 'P8'
SHARP	VLM7U	N/A	IRIS REPEATEDLY OPENS AND CLOSES PRODUCING A CHATTERING NOISE	CHECK/RESOLDER CONNECTIONS ON 26 PIN CONNECTOR 'P8'
SONY	CCD40	N/A	PICTURE JITTERS LIKE A LOAD POST IS OUT OF ADJUSTMENT	CHECK/REPLACE C486
SONY	CCDF201	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF30	N/A	PLAYBACK OR CAMERA E-E VIDEO IS DISTORTED AND NOISY - APPEARS THAT HEADS MAY BE DIRTY	CHECK/REPLACE CAPACITOR KIT (P/N# A-7190-069-A)
SONY	CCDF30	N/A	SUPER IMPOSED VIDEO IS DISTORTED	PERFORM PLL ADJUSTMENT ON SS-86 BOARD
SONY	CCDF301	N/A	CAMERA WILL NOT POWER UP	CHECK/REPLACE DT77H
SONY	CCDF301	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF301	N/A	NO OR ONE CHANNEL OF AUDIO	CHECK/REPLACE C401 ON SS-100 BOARD
SONY	CCDF301	N/A	PICTURE ROLLS IN VIEWFINDER WHEN LENS IS COVERED OR ON A DARK SCENE	CHECK/REPLACE C253
SONY	CCDF302	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF33	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF34	N/A	LOW VIDEO OUTPUT ON PLAYBACK OF PRE-RECORDED TAPES	ADD 1uF @ 50v FROM PIN 4 OF IC202 TO GROUND
SONY	CCDF35	N/A	NO VIDEO FROM CAMERA BLOCK	CHECK/REPLACE C704 FOR LEAKAGE
SONY	CCDF35	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF36	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF40	N/A	NO OR ONE CHANNEL OF AUDIO	CHECK/REPLACE C401 ON SS-100 BOARD
SONY	CCDF40	N/A	PLAYBACK OR CAMERA E-E VIDEO IS DISTORTED AND NOISY - APPEARS THAT HEADS MAY BE DIRTY	CHECK/REPLACE CAPACITOR KIT (P/N# A-7190-071-A)
SONY	CCDF401	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF402	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF45	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF46	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF501	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF501	N/A	DRUM SPINS SLOWLY AND MAKES ERRATIC NOISE	CHECK/REPLACE C911
SONY	CCDF501	N/A	NO MECHANICAL FUNCTIONS	CHECK/REPLACE PS501
SONY	CCDF501	N/A	VIEWFINDER ROLLS AFTER WARM-UP	CHECK/REPLACE 'CC-39' BOARD
SONY	CCDF55	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF55	N/A	NO PLAYBACK AUDIO	CHECK/REPLACE C401
SONY	CCDF55	N/A	NO VIDEO FROM CAMERA BLOCK	CHECK/RESOLDER CONNECTIONS ON PIN#4 OF W801 FLEX CONNECTOR
SONY	CCDF55	N/A	DRUM SPINS SLOWLY AND MAKES ERRATIC NOISE	CHECK/REPLACE C911
SONY	CCDF55	N/A	NO OR ONE CHANNEL OF AUDIO	CHECK/REPLACE C401 ON SS-100 BOARD
SONY	CCDF56	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF56	N/A	DISTORTED PLAYBACK VIDEO	CHECK/REPLACE C263
SONY	CCDF701	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF73	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF77	N/A	DRUM SPINS SLOWLY AND MAKES ERRATIC NOISE	CHECK/REPLACE C911
SONY	CCDF77	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDF77	N/A	NO OR ONE CHANNEL OF AUDIO	CHECK/REPLACE C401 ON SS-100 BOARD
SONY	CCDFX310	N/A	CAMERA SECTION WILL NOT TURN ON	CHECK/REPLACE Q903
SONY	CCDFX310	N/A	VENETIAN BLIND EFFECT IN THE VIDEO	CHECK/REPLACE IC801
SONY	CCDFX310	N/A	NO COLOR ON PLAYBACK	CHECK/REPLACE L305
SONY	CCDFX410	N/A	NO PLAYBACK VIDEO - CAMERA E-E MODE OK	CHECK/RESOLDER CONNECTIONS ON CN-002 ON 'CS-31' BOARD
SONY	CCDFX410	N/A	CAPSTAN RUNS BACKWARDS	CHECK/REPLACE CAPSTAN MOTOR
SONY	CCDFX410	N/A	CAPSTAN RUNS TOO FAST	CHECK/REPLACE CAPSTAN MOTOR
SONY	CCDFX410	N/A	NO CAMERA VIDEO	CHECK/REPLACE IC712
SONY	CCDFX411	N/A	NO FUNCTIONS WORK	CHECK/RESOLDER CONNECTIONS ON CONNECTOR CN-002 OR PLUG ITSELF NOT SEATED
SONY	CCDFX420	N/A	WILL NOT GO INTO CAMERA STAND-BY MODE - VTR WORKS OK	CHECK/REPLACE S581 STBY/LOCK SWITCH
SONY	CCDFX420	N/A	PLAYBACK PICTURE CUTS IN AND OUT	CHECK/REPLACE IC501
SONY	CCDFX430	N/A	NO POWER	CHECK/RESOLDER CONNECTIONS ON CN504
SONY	CCDFX510	N/A	NO E-E VIDEO AND HAS SOME NOISE IN VIEWFINDER	CHECK/REPLACE IC709
SONY	CCDFX510	N/A	NO COLOR IN RECORD OR PLAYBACK - INTERMITTENT	CHECK/RESOLDER CONNECTIONS ON C310 ON 'VA74' BOARD
SONY	CCDFX510	N/A	NO POWER	CHECK/REPLACE X503 MASTER CLOCK CRYSTAL
SONY	CCDFX510	N/A	LOSES MEMORY WHEN REMOVING MAIN BATTERY	CHECK/REPLACE C891
SONY	CCDFX510	N/A	TOTALLY INOPERABLE	CHECK/REPLACE IC506 (X503 WAS NOT OSCILLATING)
SONY	CCDFX630	N/A	WHEN TRYING TO EJECT, TAPE GUIDES WOULD COME BACK HALF WAY THEN LOAD AGAIN	CHECK/REPLACE PS500 ON VS1 BOARD FOR OPEN
SONY	CCDFX710	N/A	LCD INDICATOR OUT OR INTERMITTENT	CHECK/RESOLDER CONNECTIONS ON CN512 OR REPLACE CONNECTOR (P/N# 1-691-521-11)
SONY	CCDFX710	N/A	NO VIDEO IN CAMERA MODE - NONE IN VIEWFINDER OR VIDEO OUT.	CHECK/REPLACE IC707
SONY	CCDFX710	N/A	KEEPS BLOWING F950	TRY INSULATING EVF (7 WIRE) HARNESS
SONY	CCDFX730	N/A	BLUE LCD - MULTI COLORS ON LCD - NO VIDEO IN LCD MONITOR	CHECK/RESOLDER CONNECTIONS ON IC002
SONY	CCDSC5	N/A	NO LCD OPERATION - FLOURESCENT TUBE DOES LIGHT UP	CHECK/REPLACE L004 FOR OPEN ON PD42 BOARD
SONY	CCDSP7	N/A	PLAYBACK OR CAMERA E-E VIDEO IS DISTORTED AND NOISY - APPEARS THAT HEADS MAY BE DIRTY	CHECK/REPLACE CAPACITOR KIT (P/N# A-7190-071-A)
SONY	CCDSP7	N/A	DISTORTED SELF RECORDED PICTURE - PRE RECORDED TAPES ARE OK	CHECK/REPLACE C353
SONY	CCDSP9	N/A	PLAYBACK OR CAMERA E-E VIDEO IS DISTORTED AND NOISY - APPEARS THAT HEADS MAY BE DIRTY	CHECK/REPLACE CAPACITOR KIT (P/N# A-7190-071-A)
SONY	CCDTR101	N/A	VERTICAL FOLDOVER IN THE VIEWFINDER	CHECK/REPLACE C512
SONY	CCDTR101	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR101	N/A	CASSETTE COMPARTMENT EJECTS WITH OR WITHOUT A TAPE IN UNIT	CHECK/REPLACE FP-422 FLEX CABLE DUE TO A RIP OR TEAR
SONY	CCDTR101	N/A	STEADY SHOT WOULD JERK FROM SIDE TO SIDE	CHECK ADJUSTMENT OF ADDRESS #12 AND ADDRESS #13 - THESE ARE VERY CRITICAL - CHECK BEFORE CHANGING PARTS
SONY	CCDTR101	N/A	NO VIDEO IN THE VIEWFINDER AFTER WARM UP	CHECK/REPLACE Q304 (INTERMITTENT)
SONY	CCDTR200	N/A	BROKEN IMPEDANCE ROLLER	REPLACE WITH NEW PART (P/N# X-3941-930-2)
SONY	CCDTR200	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR21	N/A	NO E-E VIDEO IN VTR OR CAMERA	CHECK/REPLACE IC156
SONY	CCDTR21	N/A	LENS COVER INDICATOR SHOWS THAT LENS IS CLOSED EVEN THOUGH IT IS OPEN	CHECK/REPLACE S002
SONY	CCDTR21	N/A	INTERMITTENT 5 MINUTE WARNING/CHECK INDICATOR IN VIEW FINDER	CHECK/RESOLDER CONNECTIONS ON CN521 AND W522
SONY	CCDTR300	N/A	BROKEN IMPEDANCE ROLLER	REPLACE WITH NEW PART (P/N# X-3941-930-2)
SONY	CCDTR31	N/A	NO PLAYBACK VIDEO - RECORDS OK - PUT INTO PAUSE AND IT HAS DISTORTED VIDEO	CHECK/REPLACE Q024
SONY	CCDTR31	N/A	DISTORTED PICTURE ON PLAYBACK	CHECK/RESOLDER CONNECTIONS ON L160
SONY	CCDTR3300	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR3300	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR3300	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR3300	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR3300	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR3300	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR3300	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR3300	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR3300	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR4	N/A	VTR WORKS FINE BUT UNIT SHUTS DOWN WHEN CAMERA IS SELECTED	CHECK/REPLACE C133
SONY	CCDTR4	N/A	WILL NOT POWER UP AFTER TURNING OFF - WORKS NORMAL ON FIRST TURN ON - YOU MUST REMOVE BATTERY OR SOURCE TO TURN ON AGN.	CHECK/RESOLDER CONNECTIONS ON Q612
SONY	CCDTR4	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR40	N/A	UNIT PLAYS WITH NO TAPE INSIDE - ALSO DOES NOT SENSE REEL ROTATION	CHECK/REPLACE PS500 FOR OPEN
SONY	CCDTR400	N/A	UNIT PLAYS WITH NO TAPE INSIDE - ALSO DOES NOT SENSE REEL ROTATION	CHECK/REPLACE PS500 FOR OPEN
SONY	CCDTR400	N/A	NO LOADING AND TAPE JAMMED IN UNIT	CHECK/REPLACE LOADING GEAR (B)
SONY	CCDTR44	N/A	LINES IN CAMERA VIDEO	CHECK/RESOLDER CONNECTIONS ON IC201
SONY	CCDTR44	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR44	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR44	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR44	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR44	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR44	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR44	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR44	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR44	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR5	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR5	N/A	RECORDING APPEARS TO BE WORKING BUT DOESN'T - PRE-RECORDED TAPES PLAYBACK OK	CHECK FOR OPEN TRACE BETWEEN R334 AND R330 ON 'VS-22' BOARD
SONY	CCDTR500	N/A	NO COLOR IN E-E MODE	CHECK/REPLACE CT601
SONY	CCDTR500	N/A	BROKEN IMPEDANCE ROLLER	REPLACE WITH NEW PART (P/N# X-3941-930-2)
SONY	CCDTR500	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR51	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR514	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR514	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR514	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR514	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR514	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR514	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR514	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR514	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR514	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR54	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR54	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR54	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR54	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR54	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR54	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR54	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR54	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR54	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR6	N/A	HORZ. FOLD IN PLAYBACK - NO COLOR	CHECK/REPLACE IC203
SONY	CCDTR600	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTR600	N/A	NO FUNCTIONS AT ALL - DOES MAKE A BEEP WHEN CHANGING FROM CAMERA MODE TO VTR MODE	CHECK/RESOLDER CONNECTIONS ON CN504
SONY	CCDTR61	N/A	DRUM MOTOR NOISE MAY BE HEARD ON RECORDINGS	INSTALL CUSHION (P/N# 3-956-191-01)
SONY	CCDTR614	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR614	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR614	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR614	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR614	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR614	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR614	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR614	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR614	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR64	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR65	N/A	DRUM MOTOR NOISE MAY BE HEARD ON RECORDINGS	INSTALL CUSHION (P/N# 3-956-191-01)
SONY	CCDTR7	N/A	NO COLOR RECORDED FROM CAMERA	CHECK/RESOLDER CONNECTIONS ON CT-141 TRIMMER CAPACITOR
SONY	CCDTR7	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR70	N/A	UNIT PLAYS WITH NO TAPE INSIDE - ALSO DOES NOT SENSE REEL ROTATION	CHECK/REPLACE PS500 FOR OPEN
SONY	CCDTR700	N/A	DRUM MOTOR NOISE BEING RECORDED ON TAPE	ADD MICROPHONE RUBBER (P/N# 3-960-679-01) AND MICROPHONE WEIGHT (P/N# 3-960-627-01)
SONY	CCDTR700	N/A	SEVERE DROP OUTS IN VIDEO REMOVE R240 IF INSTALLED	CHANGE C239 TO A 1uF @ 16v (P/N# 1-135-091-00), INSTALL A 1000pF (P/N# 1-162-964-11) AT R157, CHANGE R161 TO A 100k
SONY	CCDTR71	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR71	N/A	DROPOUTS IN THE VTR PLAYBACK MODE	CHECK/REPLACE C289
SONY	CCDTR71	N/A	NO VIDEO ON E-E	CHECK/REPLACE IC802
SONY	CCDTR71	N/A	NO CAMERA FUNCTIONS WORK - HORZ LINES IN VIEWFINDER	CHECK/RESOLDER CONNECTIONS ON L852
SONY	CCDTR710	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR710	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR710	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR710	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR710	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR710	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR710	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR710	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR710	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR714	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR714	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR714	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR714	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR714	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR714	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR714	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR714	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR714	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR73	N/A	NO FUNCTIONS AT ALL - DOES MAKE A BEEP WHEN CHANGING FROM CAMERA MODE TO VTR MODE	CHECK/RESOLDER CONNECTIONS ON CN504
SONY	CCDTR73	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTR74	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR74	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR74	N/A	DEAD - NO POWER	CHECK/RESOLDER CONNECTIONS ON J001 (BATTERY CONTACT)
SONY	CCDTR74	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR74	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR74	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR74	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR74	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR74	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR74	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR77	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR77	N/A	DEAD - NO LCD	CHECK/REPLACE W501 FLEX CABLE
SONY	CCDTR78	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR78	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR78	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR78	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR78	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR78	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR78	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR78	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR78	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR80	N/A	UNIT PLAYS WITH NO TAPE INSIDE - ALSO DOES NOT SENSE REEL ROTATION	CHECK/REPLACE PS500 FOR OPEN
SONY	CCDTR81	N/A	NO E-E VIDEO AT TURN ON, THEN AFTER ON FOR AWHILE, VIDEO WOULD FLICKER	REMOVE FLUX FROM IMAGER BOARD
SONY	CCDTR81	N/A	COLORED SNOW WITH NO PICTURE - NOISE IN PICTURE - PICTURE WITH ARCING DOTS	CHECK/REPLACE IC101
SONY	CCDTR81	N/A	WHEN PLAYING A BACK A TAPE, THE VIDEO WOULD GO BLACK SCREEN	CHECK/REPLACE Q438 (INTERMITTENTLY OPENS)
SONY	CCDTR81	N/A	NO DRUM ROTATION	CHECK/REPLACE R629 AND R630
SONY	CCDTR81	N/A	DEAD - NO INITIALIZATION	CHECK/REPLACE X601
SONY	CCDTR81	N/A	NO PIX IN VIEWFINDER DURING RECORD - PLAYBACK VIDEO IS OK	CHECK/REPLACE IC301
SONY	CCDTR81	N/A	MECHANICAL NOISE HEARD IN REWIND OR PLAY/RECORD MODES	CHECK/REPLACE GEAR CONVERSION ASSY. (P/N# X-3727-930-3)
SONY	CCDTR814	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR814	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR814	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR814	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR814	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR814	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR814	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR814	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR814	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR83	N/A	NO FUNCTIONS AT ALL - DOES MAKE A BEEP WHEN CHANGING FROM CAMERA MODE TO VTR MODE	CHECK/RESOLDER CONNECTIONS ON CN504
SONY	CCDTR83	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTR84	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR84	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR84	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR84	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR84	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR84	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR84	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR84	N/A	DEAD	CHECK/RESOLDER CONNECTIONS ON CN003 ON THE DD-80 PCB
SONY	CCDTR84	N/A	DEAD	CHECK/RESOLDER CONNECTIONS ON IC400
SONY	CCDTR84	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR84	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR86	N/A	INTERMITTENT OR CONSTANT MIC/AUDIO DISTORTION	CHECK/REPLACE MIC JACK (P/N# 1-568-027-11)
SONY	CCDTR88	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR88	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR88	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR88	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR88	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR88	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR88	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR88	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR88	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR9	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR91	N/A	NO CAMERA VIDEO THROUGH VIEWFINDER OR VIDEO OUTPUT	CHECK/RESOLDER CONNECTIONS ON L651
SONY	CCDTR91	N/A	UNIT WILL NOT EJECT TAPE AND GOES INTO 'CAUTION' MODE	CHECK/REPLACE LOADING MOTOR AND PS501 (P/N# 1-576-123-21)
SONY	CCDTR91	N/A	NO CAMERA OPERATION - PICTURE IS WHITE SATURATED	CHECK/REPLACE IC604
SONY	CCDTR910	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR910	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR910	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR910	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR910	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR910	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR910	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR910	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR910	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR916	N/A	INTERMITTENT OR CONSTANT MIC/AUDIO DISTORTION	CHECK/REPLACE MIC JACK (P/N# 1-568-027-11)
SONY	CCDTR93	N/A	NO FUNCTIONS AT ALL - DOES MAKE A BEEP WHEN CHANGING FROM CAMERA MODE TO VTR MODE	CHECK/RESOLDER CONNECTIONS ON CN504
SONY	CCDTR93	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTR94	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR94	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR94	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR94	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR94	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR94	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR94	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR94	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR94	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR96	N/A	INTERMITTENT OR CONSTANT MIC/AUDIO DISTORTION	CHECK/REPLACE MIC JACK (P/N# 1-568-027-11)
SONY	CCDTR98	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR98	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR98	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR98	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR98	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR98	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR98	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTR98	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR98	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR99	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTR99	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTR99	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTR99	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTR99	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTR99	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTR99	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTR99	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTR99	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV11	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV11	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV11	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV11	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV11	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV11	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV11	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV11	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV11	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV11	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV11	N/A	DEAD BUT DRAWS 0.32 AMPS REGARDLESS OF MODE	RE-SEAT FP-220 REF# 817 BOARD
SONY	CCDTRV119	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV119	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV119	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV119	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV119	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV119	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV119	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV119	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV119	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV119	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV19	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV19	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV19	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV19	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV19	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV19	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV19	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV19	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV19	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV19	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV21	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV21	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV21	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV21	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV21	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV21	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV21	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV21	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV21	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV21	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV211	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV211	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV211	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV211	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV211	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV211	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV211	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV211	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV211	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV211	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV29	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV29	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV29	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV29	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV29	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV29	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV29	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV29	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV29	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV29	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV30	N/A	NO PICTURE IN THE LCD MONITOR	DO PROCEDURE 'TF110' FROM SERVICE MANUAL TO RESTORE DATA
SONY	CCDTRV40	N/A	NO PICTURE IN THE LCD MONITOR	DO PROCEDURE 'TF110' FROM SERVICE MANUAL TO RESTORE DATA
SONY	CCDTRV41	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDTRV41	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV41	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV41	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV41	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV41	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV41	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV41	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV41	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV41	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV54	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV70	N/A	NO PICTURE IN THE LCD MONITOR	DO PROCEDURE 'TF110' FROM SERVICE MANUAL TO RESTORE DATA
SONY	CCDTRV81	N/A	NOT EJECTING - DRUM SPINS FOR A SECOND THEN STOPS	CHECK/REPLACE X502 CRYSTAL ON THE VC125 BOARD
SONY	CCDTRV81	N/A	NO REWIND OR REVIEW - NOISE IN PLAY MODE	CHECK/REPLACE LOOSE MAGNET ON SUPPLY REEL
SONY	CCDTRV81	N/A	DOOR WON'T CLOSE ALL THE WAY	CHECK/REPLACE MODE SELECT SWITCH (IF CLEANING DOESN'T SOLVE, THEN REPLACE SWITCH )
SONY	CCDTRV81	N/A	EJECTS IMMEDIATELY AFTER LOADING	CHECK THE EXIT GUIDE REF# 752 TO MAKE SURE IT IS IN THE TRACK
SONY	CCDTRV81	N/A	DRUM MOTOR IS UNUSUALLY NOISY - SOUNDS LIKE SOMETHING IS RUBBING	REMOVE THE BOTTOM PLATE OF THE DRUM MOTOR ASSY. AND TIGHTEN (3) LOOSE SCREWS INSIDE
SONY	CCDTRV81	N/A	NOT EJECTING TAPES	CHECK TENSION REGULATOR REF# 833 FOR POSSIBLE JAMMING
SONY	CCDTRV81	N/A	PINCH ROLLER MAY JUMP UP OVER THE 'T' BASE BLOCK ASSY.	CHECK/REPLACE 'T' BASE BLOCK ASSY. (P/N# A-7040-418-B) WITH AN IMPROVED TYPE
SONY	CCDTRV81	N/A	EATS TAPES	CHECK REF# 765 FOR BEING BENT AND REF# 783 SPRING LOOSE
SONY	CCDTRV81	N/A	WON'T LOAD TAPE (DRUM NOT TURNING)	CHECK/REPLACE M901 DRUM MOTOR
SONY	CCDTRV81	N/A	WON'T THREAD TAPE DUE TO HIGH TAPE TENSION	CHECK TENSION SPRING REF# 769 TO SEE IF DISLODGED
SONY	CCDV101	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDV101	N/A	UNIT LOADS AND UNLOADS BUT REELS WILL NOT TURN	CHECK/REPLACE IC005
SONY	CCDV101	N/A	NOT RECORDING RF FOR HEAD #2	CHECK/REPLACE Q202
SONY	CCDV110	N/A	AGC OVERLOAD IN VIDEO FROM CAMERA OR LINE INPUTS	CHECK/REPLACE VD-5 BOARD
SONY	CCDV5000	N/A	UNIT SHUTS DOWN WHEN USING BATTERY	CHECK/REPLACE IC103
SONY	CCDV5000	N/A	NO PLAYBACK PICTURE - JUST A GARBLED DISPLAY	CHECK/REPLACE X703
SONY	CCDV5000	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDV701	N/A	NO VIDEO IN VTR MODE - AUDIO GOOD	CHECK/REPLACE L215 ON THE 'SS-134' BOARD
SONY	CCDV701	N/A	NO AUDIO IN VTR OR CAMERA MODE	CHECK/REPLACE C406 AND C407
SONY	CCDV801	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDV9	N/A	EXCESSIVE BRIGHTNESS AND NEGATIVE IMAGE IN VIEWFINDER AFTER REPLACING MCB BOARD	CHECK R908/R923 FOR REVERSED LOCATIONS
SONY	CCDV99	N/A	POOR PICTURE - TAPE PATH PROBLEMS - LOOSE LOAD POSTS	APPLY LOCTITE 221 (P/N# 7-432-090-41) TO THE THREADS OF THE LOADING POSTS
SONY	CCDVX3	N/A	NO VIDEO OUT - HORIZONTAL LINES IN VIEWFINDER	CHECK/REPLACE FP-531 AND FP-526 FLEX CONNECTORS - THESE MAY HAVE SPOTS WHERE THE INSULATION HAS WORN OFF
SONY	CCDVX3	N/A	DEW SENSOR ACTIVATES INTERMITTENTLY	CHECK/RESOLDER CONNECTIONS ON PINS 1-4 OF FP-523
SONY	CCDVX3	N/A	MECHANISM MAKES A SCRAPING SOUND OR DRUM MOTOR WON'T TURN	CHECK SCREW THAT HOLDS REF# 164 TO SEE IF IT HAS LOOSENED
SONY	CVD1000	N/A	DOUBLE IMAGE OR GHOSTING IN THE PICTURE WITH TAPE NOT IN THE UNIT AND POWER ON OR IF VIDEO IS INPUTTED THRU VIDEO 1	CHANGE R401 AND R402 TO 15k
SONY	CVD1000	N/A	DISTORTION ON E-E PICTURE AFTER ENDING SLOW MOTION PLAYBACK	ADD DIODE (P/N 8-719-911-19) ANODE TO PIN#4 AND CATHODE TO PIN#30 OF IC501
SONY	EVS3000	N/A	TAPE STOPS DURING PLAYBACK - AND ALL FUNCTIONS EXCEPT POWER AND EJECT ARE DISABLED.	CHECK EMERGENCY MODE DATA ON PAGE 0,ADDRESS 06 OR 07 - IF DATA IS 06 OR 08,DRUM PG IS OFF - REVERSE C448 POLARITY
SONY	EVS350	N/A	WILL NOT OPERATE IN THE TIMER ACTIVATED RECORD MODE	CHECK/REPLACE IC001 WITH NEW TYPE (P/N# 8-752-809-35)
SONY	EVS900	N/A	WILL NOT LOAD TDK TAPES	CHECK/REPLACE CASSETTE COMPARTMENT (P/N# A-7090-893-A)
SONY	GV200	N/A	HORZ TEARING IN THE PLAYBACK PICTURE	CHECK/REPLACE LOADING POST TO THE RIGHT OF THE DRUM MOTOR (P/N# X-3728-808-4)
SONY	GV300	N/A	HORZ TEARING IN THE PLAYBACK PICTURE	CHECK/REPLACE LOADING POST TO THE RIGHT OF THE DRUM MOTOR (P/N# X-3728-808-4)
SONY	GV8	N/A	HORZ TEARING IN THE PLAYBACK PICTURE	CHECK/REPLACE LOADING POST TO THE RIGHT OF THE DRUM MOTOR (P/N# X-3728-808-4)
SONY	GV9	N/A	HORZ TEARING IN THE PLAYBACK PICTURE	CHECK/REPLACE LOADING POST TO THE RIGHT OF THE DRUM MOTOR (P/N# X-3728-808-4)
SYLVANIA	VCC147	N/A	DARK PICTURE IN THE VIEW FINDER	CHECK/REPLACE V/F CRT OR CRT SOCKET CONNECTIONS
SYLVANIA	VCC147	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN VIEWFINDER	CLEAN VIEWFINDER CRT PINS WITH SOME FINE SANDPAPER
SYLVANIA	VCC147	N/A	VIEWFINDER INTERMITTENT OR FADES OUT	CHECK/RESOLDER CONNECTIONS ON IC901 AND CLEAN CRT PINS
SYLVANIA	VCC147	N/A	INTERMITTENT LOSS OF VIDEO OR PICTURE GOES DARK IN THE VIEWFINDER.	CHECK/CLEAN PINS ON EVF CRT - ESPECIALLY PINS 4 & 5
SYLVANIA	VCC147	N/A	DEAD SHORT WITH PC FOIL BURNED	PWR CONN. SHORTING TO FRAMEOF UNIT (DROPPED)
SYLVANIA	VCC147	N/A	PLAYS BACK A TAPE BUT NO PIX WHEN USING CAMERA	CHECK IRIS MOTOR AND IC102
WARDS	JSJ10655	N/A	BACK LIGHT COMPENSATION HAS NO EFFECT	IF R863 IS A 22k REPLACE IT WITH A 3.3k
WARDS	JSJ10655	N/A	WILL NOT POWER UP (AC OR DC)-OR SHUTS DOWN WITHIN A FEW SECONDS.	CHECK C927 AND C936 FOR ELECTROLYTE LEAKING,Q914 AND F901--EXAMINE CIRCUIT FOIL NEAR LEAKAGE FOR OPENS.

LAMSON Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675  TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:lamsonsm@gmail.com    YAHOO MESSENGER ID : myrna_q_ng or saishu_ng SKYPE ID: myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be using the old address and phone no. in the future. Please be noted when calling us, sending letters, parcels or buying our products> OLD Address: 681 Carmen Building, Ronquillo St. Quiapo, Manila, Philippines Phone:00632-7332936 7332940 Fax:00632-7332940 E-mail: